JUKI MEB-3810N Series Instruction Manual page 112

No. Setting item
Compensation of needle thread ten-
41
sion at right parallel section
Compensation of needle thread ten-
42
sion at left parallel section
Compensation of needle thread ten-
43
sion at top of eyelet
Compensation of needle thread ten-
44
sion at right bottom of eyelet
Compensation of needle thread ten-
45
sion at left bottom of eyelet
Compensation of needle thread ten-
46
sion bartack, right
Compensation of needle thread ten-
47
sion bartack, left
Compensation of needle thread ten-
48
sion bartack, right 2
Compensation of needle thread ten-
49
sion bartack, left 2
Compensation of needle thread ten-
50
sion at sewing start
Compensation of needle thread ten-
51
sion at sewing end
Compensation of needle thread ten-
52
sion at the time of thread trimming
Compensation of needle thread ten-
53
sion at the time of stop
(When the needle thread clamp unit is
selected as an option)
54 Compensation of needle thread tension
for drawing needle thread clamped by
the needle thread clamp unit
*1 : Knife No.
a
0 ... Decorative
buttonhole
*2 : Setting range of cut length
Specifications
Thread trimming type
Needle thread trimmer type
J type
Overall thread trimmer type
Needle thread trimmer type
C type
Overall thread trimmer type
*3 : Setting range of the number of stitches of parallel section, of taper bar and of straight bar
The number of stitches using the stitch length in the range from 0.5 to 4.0 mm
*4 : Needle thread tension compensation value setting range
0 ≦ (Data No. 40 Needle thread tension) + (Data Nos. 41 to 51 Respective compensation values of needle thread) ≦ 200
0 ≦ (Memory switch No. 08 Needle thread tension when the sewing machine's needle thread trimmer trims the needle thread) +
(Data No. 52 Compensation value of needle thread tension at the time of thread trimming) ≦ 200
0 ≦ (Memory switch No. 10 Needle thread tension when the sewing machine stops) + (Data No. 53 Compensation value of needle
thread tension when the sewing machine stops) ≦ 200
(When the needle thread clamp unit is selected as an option)
0 ≦ (Memory switch No. 33 Needle thread tension when needle thread clamp unit trims the thread) + (Data No. 52 Compensation
value of needle thread tension at the time of thread trimming) ≦ 200
0 ≦ (Memory switch No. 34 Needle thread tension when the needle thread clamp unit draws the needle thread) + (Data No. 54
Compensation value of needle thread tension when the needle thread clamp unit draws the needle thread) ≦ 200
Compensation value of needle thread tension at right side of
parallel section
Compensation value of needle thread tension at left side of
parallel section
Compensation value of thread tension at top of eyelet
Compensation value of needle thread tension at right side of
bottom of eyelet
Compensation value of needle thread tension at left side of
bottom of eyelet
Needle thread tension compensation value of the right side
of bartack
Needle thread tension compensation value of the left side of
bartack
Needle thread tension compensation value of the right side
2 of bartack
Needle thread tension compensation value of the left side 2
of bartack
Compensation value of needle thread tension at sewing start
Compensation value of needle thread tension at sewing end
Compensation value of needle thread tension at the time of
thread trimming of the sewing machine
Compensation value of needle thread tension at the time of
stop of the sewing machine
Compensation value of the needle thread tension for drawing
the needle thread after the needle thread clamp unit has
clamped the needle thread
No.
1
b
2
3
4
1 to 6 ... Eyelet
5
buttonhole
6
Eyelet buttonhole setting range
Description
a×b
2.1×3.2
2.5×3.8
2.9×4.4
3.0×4.6
3.2×5.4
2.7×5.1
Lockstitch buttonhole setting range
10 to 38mm
10 to 34mm
10 to 38mm
10 to 34mm
– 109 –
Setting range Unit
*4 1
*4 1
*4 1
*4 1
*4 1
*4 1
*4 1
*4 1
*4 1
*4 1
*4 1
*4 1
*4 1
*4 1
5 to 38mm
5 to 34mm
5 to 38mm
5 to 34mm