Sewing Data Entry Sheet - JUKI MEB-3810N Series Instruction Manual

16. SEWING DATA ENTRY SHEET

No. Setting item
1 Knife No.
2 Cut length
3 Cut-before/cut-after knife
4 Number of stitches of parallel
5 Number of stitches of eyelet
6 Cut space
7 Eyelet space
8 Compensation of knife position
Compensation of number of stitches
9
at sewing end
10 Compensation of turning
Compensation of turning at parallel
11
section
12 Lengthwise compensation of eyelet
13 Crosswise compensation of eyelet
14 Crosswise compensation of left eyelet
15 Crosswise compensation of left parallel
16 Left cut-space compensation
Setting of stitch bite width of right
17
bottom of eyelet
Setting of stitch bite width of left bottom
18
of eyelet
19 Setting of stitch bite width
20 Type of bartack
21 Length of taper bar
22 Number of stitches of taper bar
23 Taper bar offset
24 Number of stitches of slant taper bar
Compensation of number of stitches of
25
right taper bar
26 Straight bar length
27 Number of stitches of straight bar
28 Overlapping amount of straight bar
29 Needle throwing width of straight bar
30 Number of stitches of round bar
Number of overlapping stitches of
31
round bar 2
Needle throwing width for round
32
bartack
Needle throwing width at the top of
33
eyelet
Speed reduction of straight bar/round
34
bar
35 Sewing speed
36 Reduced speed of eyelet
37 Soft-start
Number of stitches of the sewing start
38
of thread tension
Number of stitches of the sewing end
39
of thread tension
40 Needle thread tension
Description
Shape of knife *1
Length of cloth cutting knife
Operation of cloth cutting knife
0 : Without knife 1 : Cut-before knife 2 : Cut-after knife
Number of stitches from parallel section to bottom of eyelet
Number of stitches of top of eyelet
Clearance of knife groove of parallel section
Clearance of knife groove of eyelet
Longitudinal compensation of whole needle entry
Number of stitches to increase length at sewing end
Compensation of turning at parallel section and eyelet section
Compensation of turning of parallel section and bottom of eyelet
Crosswise compensation of eyelet
Lengthwise compensation of top of eyelet
Lengthwise compensation of left side of top of eyelet
Compensation of length from left side of bottom of eyelet to left
side of parallel section
Compensation of the clearance in the left side knife slit at the
parallel section
Setting of stitch bite width of right side of bottom of eyelet
Setting of stitch bite width of left side of bottom of eyelet
Setting of stitch bite width of parallel section and taper bar
Type of bartack
0 : Without bartack 1 : Taper bar 2 : Straight bar
3 : Round bar 4 : Round bar 2
Length of taper bar
Number of stitches of taper bar *3
Overlapping amount of left/right taper bars
Number of stitches of slant section from taper bar to parallel
section
Number of stitches of compensation of right side of taper bar
Length of the straight bar
Number of stitches of the straight bar *3
Amount of overlap between the straight bar and the parallel
section
Needle throwing width of the straight bar
Number of stitches of round bar
Number of stitches that overlap at the beginning and end of
the round bar 2
Setting the needle throwing width at the right side of the round
bar is set
Setting the needle throwing width at the upper section of
eyelet is set
Reduced speed for the sewing speed of the straight bar and
round bar
Sewing speed
Reduced speed in terms of sewing speed of eyelet
Number of times of needle entries of soft-start at sewing start
Number of stitches of thread tension compensation at sewing
start
Number of stitches of thread tension compensation at sewing
end
Needle thread tension value
– 108 –
Setting range Unit
0 to 6 -
*2 1mm
0 to 2 -
3 to 100 stitch 1 stitch
4 to 20 stitch 1 stitch
−1.2 to 1.2mm 0.1mm
−1.2 to 1.2mm 0.1mm
−0.7 to 0.7mm 0.1mm
−1 to 6 stitch 1 stitch
−14 to 14 1
−14 to 14 1
−0.6 to 0.6mm 0.1mm
−0.2 to 0.6mm 0.1mm
−0.2 to 0.6mm 0.1mm
−0.6 to 0.6mm 0.1mm
−2.4 to 2.4mm 0.1mm
2.5±1.0mm 0.1mm
2.5±1.0mm 0.1mm
2.5±1.0mm 0.1mm
0 to 4 -
0.3 to 15mm 1mm
2 to 30 stitch 1 stitch
0.5 to 2.0mm 0.1mm
2 to 30 stitch 1 stitch
−30 to 0 stitch 1 stitch
2.0 to 10.0mm 0.1mm
2 to 10 stitch 1 stitch
0.0 to 2.0mm 0.1mm
1.5 to 3.5mm 0.1mm
4 to 20 stitch 1 stitch
0 to 4 stitch 1 stitch
2.5±1.0mm 0.1mm
2.5±1.0mm 0.1mm
−600 to 0 sti/min 100 sti/min
400 to 2500 sti/min 100 sti/min
−600 to 0 sti/min 100 sti/min
0 to 6 rotations 1 rotation
0 to 3 stitch 1 stitch
0 to 3 stitch 1 stitch
0 to 200 1