Chrysler Sebring 2004 Service Manual page 1168

JR
BUMPERS
SPECIFICATIONS - TORQUE
FRONT FASCIA
REMOVAL
REMOVAL - JR-41 . . . . . . . . . . . . . . . . . . . . . . 1
REMOVAL - JR-27 . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION
INSTALLATION - JR-41
INSTALLATION - JR-27
REAR BUMPER REINFORCEMENT
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 3
REAR FASCIA
REMOVAL
REMOVAL - JR-41 . . . . . . . . . . . . . . . . . . . . . . 3
REMOVAL - JR-27 . . . . . . . . . . . . . . . . . . . . . . 4
BUMPERS
SPECIFICATIONS - TORQUE
DESCRIPTION
Rear Bumper Reinforcement
Attaching Nut
Front Suspension Crossmember
Attaching Bolt Front
Attaching Bolt Rear
Radiator Support Crossmember
Attaching Bolts
FRONT FASCIA
REMOVAL
REMOVAL - JR-41
It is not necessary to remove the headlamp assem-
blies to remove the front bumper fascia.
(1) Release hood latch and open hood.
(2) Remove fasteners attaching fascia to front
splash shields (Fig. 1).
(3) Hoist and support vehicle on safety stands.
(Refer to LUBRICATION & MAINTENANCE/HOIST-
ING - STANDARD PROCEDURE), for proper hoist-
ing and jacking procedures.
(4) Remove inner wheelhouse front wheel house
splash shield as necessary to access nut attaching
fascia wings to fender.
FRAME & BUMPERS
TABLE OF CONTENTS
page
. . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . 3
TORQUE
28 N·m (21 ft. lbs.)
109 N·m (80 ft. lbs.)
102 N·m (75 ft. lbs.)
115 N·m (85 ft. lbs.)
FRAME & BUMPERS
INSTALLATION
INSTALLATION - JR-41
INSTALLATION - JR-27
FRAME
SPECIFICATIONS - FRAME DIMENSIONS
FRONT SUSPENSION CROSSMEMBER
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 9
REAR SUSPENSION CROSSMEMBER
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 10
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 12
FRONT TOW HOOK
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 13
(5) Remove fasteners attaching top of fascia to
upper crosmember.
(6) Remove fasteners attaching bottom of fascia to
radiator closure panel and to brake ducts.
(7) Remove screws attaching fascia to front fenders.
(8) Slide fascia forward to disengage hooks attach-
ing fascia to bottom of fender.
(9) Remove fascia from vehicle.
(10) Disengage fog lamp wire connector from body
harness, if equipped.
REMOVAL - JR-27
It is not necessary to remove the headlamp assem-
blies to remove the front bumper fascia.
(1) Release hood latch and open hood.
(2) Remove fasteners attaching top of grille to
headlamp adapter assembly (Fig. 2).
(3) Hoist and support vehicle on safety stands.
(Refer to LUBRICATION & MAINTENANCE/HOIST-
ING - STANDARD PROCEDURE), for proper hoist-
ing and jacking procedures.
(4) Remove inner wheelhouse front wheel house
splash shield as necessary to access nut attaching
fascia wings to fender.
(5) Remove fasteners attaching bottom of fascia to
radiator closure panel and to brake ducts.
(6) Remove screws attaching fascia to front fenders.
(7) Slide fascia forward and separate fascia from
vehicle.
(8) Disengage fog lamp wire connectors from back
of fog lamps, if so equipped.
13 - 1
page
. . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . 4
. . . . . 5