1. Manuals
  2. Brands
  3. Chrysler Manuals
  4. Automobile
  5. Sebring Coupe
  6. Owner's manual

Chrysler Sebring Coupe Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SECTION
1
2
3
SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS
4
5
6
7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
VEHICLE CARE
8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
EMERGENCIES
9
MAINTENANCE
10
11
12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387

TABLE OF CONTENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
. . . . . . . . . . . . . . . . . . . . . . . . . . 55
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
PAGE
1
2
3
4
5
6
7
8
9
10
11
12

Advertisement

Table of Contents
loading

Related Manuals for Chrysler Sebring Coupe

Summary of Contents for Chrysler Sebring Coupe

  • Page 1: Table Of Contents

    TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
  • Page 3 INTRODUCTION CONTENTS Introduction ......4 Warnings, Cautions And Notes ... . . 5 How To Use This Manual .

  • Page 4: Introduction

    4 INTRODUCTION This manual includes instructions for standard and op- INTRODUCTION This manual has been prepared with the assistance of tional equipment available at the time this manual was service and engineering specialists to acquaint you with printed. The manufacturer reserves the right to make the operation and maintenance of your new vehicle.

  • Page 5: Introduction 5

    INTRODUCTION 5 WARNINGS, CAUTIONS AND NOTES VEHICLE IDENTIFICATION NUMBER This manual contains WARNINGS against operating Vehicle Identification Number (VIN) is found on a procedures which could result in an accident or bodily stamped plate located on the driver’s front corner of the injury.
  • Page 6 6 INTRODUCTION 3. Supplemental restraint system-air bag Overview - Instruments and controls (For driver’s seat) → p. 89 Horn switch → p. 132 4. Hazard warning flasher switch → p. 124 5. Windshield wiper and washer switch → p. 126 6.
  • Page 7 INTRODUCTION 7 2. Remote trunk lid release → p. 36 Interior 3. Power window switch → p. 43 4. Window lock switch → p. 45 5. Electric remote-controlled outside mirror switch → p. 188 6. Power door lock switch → p. 34 7.
  • Page 8 8 INTRODUCTION 2. Windshield wiper and washer → p. 126 Outside 3. Sunroof (if so equipped) → p. 46 4. Outside rear-view mirrors → p. 188 5. Whip antenna → p. 219 6. Headlights → p. 120, 292, 293 7. Front turn signal lights and parking lights →...
  • Page 9 INTRODUCTION 9 1. Inside emergency trunk release handle → p. 37 Trunk Area 2. Trunk light → p. 301 3. Jack → p. 265 4. Spare tire → p. 265 5. Tools → p. 264 E19A0720...
  • Page 10 10 INTRODUCTION QUICK INDEX If this warning light comes on… NOTE: These warning lights will illuminate for a few seconds for a bulb check when the ignition key is first turned on. Warning light Do this Ref. page ·Park the vehicle in a safe place and turn off the engine. Test the system as described on page 113.
  • Page 11 INTRODUCTION 11 If this warning light comes on… Warning light Do this Ref. page ·Park the vehicle in a safe place and turn off the engine. Check the alternator belt. If the belt is loose, broken, missing, or if the light remains P.
  • Page 12 12 INTRODUCTION If this warning light comes on… Warning light Do this Ref. page ·Have the vehicle inspected at an authorized dealer as P. 161 soon as possible. “N” indicator light in the instruemnt cluster flashes slowly (once per second) ·Your vehicle will usually be drivable and not need towing, have the engine system checked at an authorized dealer as soon as possible.
  • Page 13 INTRODUCTION 13 If you hear the sound… N50B001D Sound Do this Ref. page “Key reminder chime” P. 27, 150 A chime will sound if the driver’s door is opened while the ignition key is in the “LOCK” or “ACC” position. Remove the key to stop the chime.
  • Page 14 14 INTRODUCTION If you hear the sound… Sound Do this Ref. page If you hear a metallic sound (squeal) “Brake pad wear alarm” P. 172 when you depress the brake pedal The brake pads have worn down near the serviceable while driving.
  • Page 15 INTRODUCTION 15 If you hear the sound… Sound Warning light Do this Ref. page If you hear a “Seat belt reminder/warning chime” P. 118 chime while the If the driver’s seat belt remains unfastened 1 minute later, the engine is on, see chime will sound intermittently (12 times) when the vehicle is the warning driven.
  • Page 16 16 INTRODUCTION If this problem occurs… Problem Do this Ref. Page Cannot turn the key (1)“LOCK” to “ACC” P. 149 Turn the key while slightly turning the steering wheel right and left. (2)”ACC” to “LOCK” Vehicle with automatic transaxle Check the position of gear selector lever. The key cannot be removed unless the gear selector lever is set to the “P”...
  • Page 17 INTRODUCTION 17 If this problem occurs… Problem Do this Ref. page The engine does not start. The battery may have a weak charge. P. 278 The lights do not come on or dim. The horn does not honk or weak sound. The engine coolant temperature gauge The engine is overheated.
  • Page 18 18 INTRODUCTION If this problem occurs… Problem Do this Ref. page The vehicle is stuck in sand, mud, or 1. Carefully rock the vehicle by shifting the transmission P. 261 snow. from low to reverse. WARNING 1.When attempting to rock your vehicle out of a stuck position, be sure that no one is near the vehicle.
  • Page 19 INTRODUCTION 19 If this problem occurs… Problem Do this Ref. page The automatic transaxle does not shift There may be a problem in the automatic transaxle. P. 158, 166 when accelerating and/or the vehicle Have the vehicle inspected by an authorized dealer. does not easily begin to move.
  • Page 21 LOCKING AND UNLOCKING CONTENTS Keys ....... . .23 Power door locks......34 Sentry Key .
  • Page 22 22 LOCKING AND UNLOCKING Passenger switch ..... . .45 Sunshade ......47 Sunroof (if so equipped) .

  • Page 23: Locking And Unlocking 23

    LOCKING AND UNLOCKING 23 KEYS NOTE: The key number (A) is stamped on the plate as shown in the illustration. Make a record of the key number and store the key and key number plate in a separate place so that you can order a key from your authorized dealer if the original keys are lost.
  • Page 24 24 LOCKING AND UNLOCKING In case like these, the theft-alarm indicator (located in the instrument cluster) will blink after 10 seconds. The theft-alarm indicator will flash for approximately 30 seconds and then go off. Remove the above object from the key and turn the key back to the ACC or LOCK position.
  • Page 25 LOCKING AND UNLOCKING 25 Customer Key Programming CAUTION! You can program new keys to the system if you have two valid keys by doing the following: Do not make any alterations or additions to the sentry key system. Any alterations or additions NOTE: could cause failure of the sentry key.

  • Page 26: Door Locks (Manual)

    26 LOCKING AND UNLOCKING If an error occurs, the indicator will flash 3 times. DOOR LOCKS (MANUAL) 5. Repeat step 4 if you want to register additional keys. To lock the door without using the key Be sure to complete the entire registration process within 30 seconds after the theft-alarm indicator flashes in step General Information Your sentry key operates on a radio frequency subject to...

  • Page 27: To Lock The Door With The Key (Driver's Side Only)

    LOCKING AND UNLOCKING 27 Key reminder chime To lock the door with the key (Driver’s side only) After the ignition switch is off, if the driver’s door is opened while the ignition key is in the ignition, a chime will sound to remind you to remove the key. Forgotten-key prevention mechanism If the inside lock knobs on the doors are set to the locked position and the driver’s door or passenger’s door is...

  • Page 28: To Lock The Door From The Inside

    28 LOCKING AND UNLOCKING To lock the door from the inside CAUTION! • Make sure the doors are closed; driving with doors not completely closed is very dangerous. • Never leave a child in the vehicle unattended. F12A1720 Move the inside lock knob to the locked position (so that the red mark cannot be seen) to lock the door.

  • Page 29: Keyless Entry System

    LOCKING AND UNLOCKING 29 KEYLESS ENTRY SYSTEM To unlock the doors Pressing the UNLOCK button once will unlock the driver’s door only. Press the UNLOCK button one more LOCK time, and all doors will be unlocked. button When the driver’s door only, or all doors are unlocked UNLOCK with the reading light in the “OFF”...
  • Page 30 30 LOCKING AND UNLOCKING 2. Release the LOCK and UNLOCK buttons at the same Horn deactivation/reactivation The confirmation function can be set in the following time. three ways. Turn signal light feature–ON/OFF Each time the confirmation function is set, a buzzer will The confirmation function provided by the turn signal sound to tell you the condition of the confirmation lights when the doors are locked and the confirmation...

  • Page 31: Using The Panic Alarm

    LOCKING AND UNLOCKING 31 NOTE 1. The keyless entry system will not operate if the key is in the ignition switch. 2. The keyless transmitter will operate within about 12 m (39 ft) from the vehicle. However, the operating range PANIC may change if the vehicle is located near a TV transmit- button...

  • Page 32: Procedure For Replacing Keyless Transmitter Battery

    32 LOCKING AND UNLOCKING 7. If you wish to add another transmitter, contact an CAUTION! authorized dealer. A maximum of 4 keyless transmitters may be programmed for your vehicle. Changes or modifications not expressly approved by the manufacturer for compliance could void the user’s authority to operate the equipment.
  • Page 33 LOCKING AND UNLOCKING 33 NOTE 1. You may purchase a battery at any local store that sells +side batteries. 2. Your authorized dealer can replace the battery for you if necessary. CAUTION! -side When the transmitter is opened, be careful to keep water, dust, etc.

  • Page 34: Power Door Locks

    34 LOCKING AND UNLOCKING POWER DOOR LOCKS Rolling lock feature If the vehicle’s speed goes over 15 mph (25 km/h), all the Locking and unlocking with the door lock switch doors will lock automatically. Driver side switch Passenger side switch NOTE: The Rolling lock function can be turned ON or OFF by the following procedures: Lock...

  • Page 35: Locking And Unlocking With Key Or Inside Lock Knob

    LOCKING AND UNLOCKING 35 Locking and unlocking with key or inside lock Locking by means of the inside lock knob knob Place the inside lock knob of the driver’s door in the locked position, and both doors will be locked. TRUNK LID Lock Unlock...

  • Page 36: Remote Trunk Lid Release

    36 LOCKING AND UNLOCKING CAUTION! Do not stand behind the exhaust pipe when loading and unloading luggage. Heat from the exhaust could lead to burns. To open the trunk lid Press the TRUNK button twice within five seconds. (Refer to ‘‘Keyless entry system’’ on page 29.) The trunk lid will unlock and rise slightly.

  • Page 37: Inside Emergency Trunk Release

    LOCKING AND UNLOCKING 37 Inside emergency trunk release The handle glows in the dark after exposure to sunlight. You and your family should familiarize yourselves with the location and operation of the emergency trunk release handle. Children should be taught not to play in or around vehicles.
  • Page 38 38 LOCKING AND UNLOCKING CAUTION! • When loading objects in the trunk, position them Handle so that they will not contact the emergency trunk release handle when closing the trunk. This will 1. Tear off prevent damage to the handle that could render it inoperable.

  • Page 39: Fuel Filler

    LOCKING AND UNLOCKING 39 FUEL FILLER WARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a build up of pressure in the fuel tank that may increase while you drive.
  • Page 40 40 LOCKING AND UNLOCKING The fuel filler is located on the right rear of the body. Low fuel warning chime Hook a finger behind the fuel filler door, and pull the If a chime sounds when the low fuel warning light is on, door toward you.

  • Page 41: Engine Hood Release

    LOCKING AND UNLOCKING 41 NOTE: If the fuel tank filler tube cap is not tight while ENGINE HOOD RELEASE driving, the “Malfunction indicator light (SERVICE EN- GINE SOON)” may illuminate when the onboard diag- nostic (OBD) system performs its self check. Always tighten the fuel tank filler tube cap until you hear clicking sounds.
  • Page 42 42 LOCKING AND UNLOCKING NOTE: Only open the engine hood when the wipers are WARNING! at their parked position to prevent damage to the engine • Never release the engine hood using the release hood and wipers. lever while the vehicle is in motion. •...

  • Page 43: Power Windows

    LOCKING AND UNLOCKING 43 CAUTION! Be careful that hands or fingers are not trapped when closing the engine hood. POWER WINDOWS Open Close F13A1720 To close, unlatch the hood prop from the engine hood and place the hood prop in its retainer. Slowly lower the engine hood to about 12 inches (30 cm) from the closed position, then release it.

  • Page 44: Driver Switch

    44 LOCKING AND UNLOCKING or closed for a 30-second period even after the ignition Driver switch switch is turned off. However, once the driver’s door or the front passenger’s door is opened, the windows can- not be operated until the ignition switch is turned on again.

  • Page 45: Passenger Switch

    LOCKING AND UNLOCKING 45 2. Passenger’s door window switch Passenger switch 3. Window lock switch (When this switch is pressed into lock mode, the passen- ger switch cannot be used to open or close the door window, and the driver switch can open or close either window.

  • Page 46: Sunroof (If So Equipped)

    46 LOCKING AND UNLOCKING SUNROOF (IF SO EQUIPPED) To tilt down Press the sunroof switch (2). To stop the sunroof partway, release the sunroof switch. To open When the sunroof switch (1) is pressed, the back of the sunroof automatically goes up. When the sunroof switch (1) is pressed a second time, the sunroof automatically opens completely.

  • Page 47: Sunshade

    LOCKING AND UNLOCKING 47 2. If the battery cable is disconnected or the fuse is Sunshade replaced while the sunroof is open, the sunroof will not close normally even after reconnecting the battery cable. In this case, use the following steps. Press the switch (2) repeatedly to close the sunroof completely.

  • Page 48: Theft-Alarm System

    48 LOCKING AND UNLOCKING 3. Do not try to operate the sunroof if it is frozen closed CAUTION! (after snowfall or during extreme cold). Do not attempt to close the sunshade when the 4. Do not sit on or place heavy luggage on the sunroof or sunroof is opened.

  • Page 49: Armed Stage

    LOCKING AND UNLOCKING 49 Armed stage 3. Lock the driver’s and the passenger’s door by using Park the vehicle and stop the engine. Arm the system as the key, power door lock switch, or the remote keyless described below. transmitter. Arm the system and leave.

  • Page 50: Alarm Stage

    50 LOCKING AND UNLOCKING 7. The driver should not arm the system until first NOTE 1. The system will be armed even if the trunk lid is confirming that all passengers have left the vehicle. If the opened, but when the system is set, be sure that the trunk driver arms the system while a passenger(s) in the lid is latched.
  • Page 51 LOCKING AND UNLOCKING 51 Alarm deactivation Horn sounds! The alarm can be deactivated in the following ways. Headlights blink on and off! 1. By turning the key (in the driver’s or passenger’s door) in either direction (toward lock or unlock). 2.

  • Page 52: Disarmed Stage

    52 LOCKING AND UNLOCKING 3. If the UNLOCK button is pressed when all doors are Disarmed stage closed and no door is opened within approximately 30 Disarm..by key (or by keyless transmitter) seconds, re-arming will automatically occur. NOTE: Once the system has been disarmed, it cannot be rearmed except by repeating the arming procedure.
  • Page 53 LOCKING AND UNLOCKING 53 6. Disarm the system by unlocking the front driver’s door, passenger’s door or the trunk lid by using the key or the remote keyless transmitter. NOTE: To make sure the alarm sounds when the trunk lid is opened, open the trunk lid by using the trunk lid release lever.
  • Page 55 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS CONTENTS Front seats......57 Adjustment of the head restraints ...67 To adjust seat forward or backward .
  • Page 56 56 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS Tether anchors for the child restraint system ..85 Supplemental Restraint System (SRS) - air bag . .89 Tether strap anchor installation ... . .86 Event Data Recording.

  • Page 57: Front Seats

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 57 Your vehicle has seat belts and other features that help No safety equipment can prevent all injuries or deaths protect you and your passengers in an accident. that can occur in severe collisions, but by making sure all Seat belts are the most important safety device.
  • Page 58 58 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS WARNING! WARNING! • Do not attempt to adjust the seat while driving. • In order to reduce risk of serious or fatal injury in This can be dangerous. a collision, including from a deploying front pas- senger air bag, all front seat passengers should •...

  • Page 59: To Adjust Seat Forward Or Backward

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 59 To adjust seat forward or backward WARNING! Type 1 (Manual) To ensure the seat is locked securely, attempt to move the seat forward or backward without using the adjusting lever. Type 2 (Power, driver’s side only–if so equipped) G21B0620 Pull the seat adjusting lever and slide the seat forward or backward to the desired position.

  • Page 60: To Recline The Seatback

    60 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS Push the switch to adjust the seat forward or backward to To recline the seatback the desired position. Release the switch, and the seat will lock at that position. CAUTION! Operate the power seat with care not to have the hand or foot caught by the seat.
  • Page 61 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 61 Memory reclining knob When you fold down the seatback by using the memory reclining knob, the angle of the seatback will be memo- rized. Memory reclining knob G21C0880 Just by pushing the seatback up into position will lock it in the memorized position.
  • Page 62 62 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS WARNING! CAUTION! To minimize risk of severe or fatal personal injury in Pull the seatback lock lever, and the seatback will the event of a collision or sudden stop, both the return to its original position.

  • Page 63: To Adjust Seat Height (Driver's Side Only)

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 63 To adjust seat height (Driver’s side only) Type 2 (Power, driver’s side only-if so equipped) Front and/or rear parts of the seat cushion height can be Type 1 (Manual) adjusted. Front part of the seat cushion G21D0830 Turn the knob to raise or lower the whole seat cushion.
  • Page 64 64 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS Rear part of the seat cushion Whole seat cushion G22D0310 G22D0320 Push the switch to raise or lower the rear part of the seat Push the center of the switch to raise or lower the whole cushion.

  • Page 65: To Adjust Lumbar Support (Driver's Side Only, If So Equipped)

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 65 To adjust lumbar support (Driver’s side only, if so For access to the rear seat (passenger side entry) equipped) Weak Strong G01J0310 G21E0230 To permit rear seat entry or exit, the front seatback will A lumbar support is included in the seatback of the fold down and the seat will move forward when the driver’s seat.

  • Page 66: Rear Seats

    66 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS The rear seatbacks can be folded forward to provide REAR SEATS Rear seat capacity additional cargo area. Pull the left and/or right release knobs, and fold the rear WARNING! seatbacks forward. •...

  • Page 67: Adjustment Of The Head Restraints

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 67 Adjustment of the head restraints Adjust the head restraint height so that the center of the restraint is as close as possible to your seated eye level. Any person too tall for the restraint to reach their seated eye level, should adjust the restraint as high as possible.

  • Page 68: Seat Belts

    68 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS SEAT BELTS WARNING! Seat belts are installed in your vehicle for the protection • Lock all doors before driving to reduce the risk of of the driver and passengers. injury or ejection in a collision. Always use the seat belts.

  • Page 69: Unibelt Restraint System

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 69 WARNING! WARNING! • To reduce the risk of severe or fatal injury from a • Any child who is too small to properly wear a seat deploying passenger air bag, make sure the pas- belt must be properly restrained in an appropriate senger is also properly wearing their seat belt, child restraint system.

  • Page 70: Unibelt Instructions

    70 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS All vehicle occupant’s should sit and remain seated all UNIBELT instructions the way back in their seat with their back resting straight against the upright seat back. WARNING! To minimize the risk of personal injury in the event of a collision or sudden stop, both the driver and passenger seatbacks should always be in a nearly upright position while the vehicle is in motion.
  • Page 71 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 71 G28A0220 G28A0230 2. Grasp the metal tongue and slide it up the webbing so 3. Pull the seat belt out slowly while holding the metal that it becomes easy to pull across your body. tongue.
  • Page 72 72 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS NOTE: If a person wearing the seat belt moves their upper body or the belt completely unwinds, the retractor may switch to its Automatic Locking Retractor (ALR) child restraint installation mode and lock (see page 82), thus preventing further movement.

  • Page 73: Adjustable Seat Belt Shoulder Anchor (Front Seats)

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 73 Adjustable seat belt shoulder anchor (front seats) G28A0260 G08C0070 5. The shoulder belt portion will allow regular move- ment under normal conditions. The belt will lock in the The seat belt shoulder anchor height can be adjusted for event of an abrupt change in vehicle motion.

  • Page 74: Enhanced Driver Seat Belt Use Reminder System (Beltalert™)

    74 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS The Enhanced Warning System (BeltAlert™) will be WARNING! reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 To reduce risk of serious injury in a collision, adjust mph (8 km/h).

  • Page 75: Seat Belt Extender

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 75 Turn the ignition key to the OFF position. A single Seat belt extender chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert™) can be reac- tivated by repeating this procedure.

  • Page 76: Child Restraints

    76 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS The child restraint system should be appropriate for your WARNING! child’s weight and height and properly fit the vehicle’s • The extender should only be used if the existing seat. belt is not long enough. All children should be restrained in a restraint device that Persons who can use the standard seat belt should offers the maximum protection for their size and age.
  • Page 77 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 77 WARNING! • All children 12 years old and under should be seated in the rear seat, and properly restrained. Accident statistics indicate that children of all sizes and ages are safer when properly restrained in the rear seat rather than in the front seat.
  • Page 78 78 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS Air bag cover WARNING! WARNING! Your vehicle is also equipped with a front passenger air FRONT-FACING CHILD RESTRAINTS should al- bag. REAR-FACING CHILD RESTRAINTS or INFANT ways be used in the rear seat whenever possible; if RESTRAINTS must NOT be used in the front passenger one must be used in the front passenger seat, adjust seat as it places an infant too close to the passenger air...
  • Page 79 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 79 NOTE: Before purchasing a child restraint system, try WARNING! installing it in the rear seat to ensure a good fit. Due to the • It is important to use an approved rear facing location of the seat belt buckles and the shape of the seat infant restraint until the infant is one year old to cushion it may be difficult to securely install some child...
  • Page 80 80 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS Installing child restraint system to the lower Child restraint system that is compatible with the anchorage (LATCH System) LATCH (Lower Anchors and Tethers for Children) System Your vehicle’s rear seat is equipped with lower anchor- ages for attaching a child restraint system that is compat- A: Rear-facing child restraint ible with the LATCH System.
  • Page 81 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 81 Installation 3. If your child restraint system requires the use of a top tether strap, refer to ‘‘Tether anchors for child restraint systems’’ on page 85. 4. Push and pull the child restraint system in all direc- tions to be sure it is firmly secured.

  • Page 82: Installing A Child Restraint System To A Unibelt At The Rear Seat Positions Or The Front Passenger Seat (With Emergency/Automatic Locking Mechanism)

    82 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS Installing a child restraint system to a UNIBELT WARNING! at the rear seat positions or the front passenger • If there is any foreign material in or around the seat (With emergency/automatic locking mechanism) lower anchorage connectors, remove it before in- stalling the child restraint system.
  • Page 83 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 83 Children 12 years old and under should be restrained in Installation: the rear seat only, whenever possible, although the front 1. Place the child restraint system in the rear seating passenger seat belt can also be the converted to ALR position as shown in the illustration.
  • Page 84 84 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS G18C0550 G18C0560 3. To activate the ALR mode, slowly pull the shoulder 5. After confirming that the belt is locked, grab the part of the belt all the way out until it stops, then let the shoulder part of the belt near the buckle and pull up to belt feed back into the retractor.

  • Page 85: Tether Anchors For The Child Restraint System

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 85 6. If your child restraint system requires the use of a top Tether anchors for the child restraint system tether strap, refer to “Anchors for the child restraint system” on page 85. 7.

  • Page 86: Tether Strap Anchor Installation

    86 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS Tether strap anchor installation WARNING! Child restraint tether anchorages are designed to withstand only those loads imposed by a correctly fitted child restraint system. Under no circumstances are they to be used for adult seats, or harnesses, or for attaching other items or equipment to the vehicle.

  • Page 87: Seat Belts And Pregnant Women

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 87 Seat Belts And Pregnant Women WARNING! We recommend that pregnant women use the seat belts • Children who are not buckled up, with all the throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe.

  • Page 88: Maintenance And Inspection Of Seat Belts

    88 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS MAINTENANCE AND INSPECTION OF SEAT BELTS Sleeve Good The seat belt webbing may be cleaned with mild soap or detergent solution. Allow the belts to dry in the shade. Do not allow them to retract until completely dry. Do not attempt to bleach or re-dye belts.

  • Page 89: Supplemental Restraint System (Srs) - Air Bag

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 89 Supplemental Restraint System (SRS) - air bag WARNING! This vehicle is equipped with a Supplemental Restraint System (SRS), which includes air bags for the driver and All seat belt assemblies, including retractors and front passenger.
  • Page 90 90 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS WARNING! WARNING! • IT IS VERY IMPORTANT TO ALWAYS WEAR • IT IS VERY IMPORTANT TO BE PROPERLY YOUR SEAT BELT PROPERLY EVEN WITH SEATED. AN AIR BAG. A driver or front passenger sitting too close to the •...
  • Page 91 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 91 G28G1570 G28G1760 WARNING! WARNING! • • Do not sit on the edge of the seat or lean your head Infants and small children should never ride or chest close to the steering wheel or instrument unrestrained, or lean against the instrument panel.
  • Page 92 92 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS Air bag cover WARNING! • REAR- FACING CHILD RESTRAINTS or INFANT RESTRAINTS must NOT be used in the front pas- senger seat as it places an infant too close to the passenger air bag.
  • Page 93 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 93 WARNING! • FRONT- FACING CHILD RESTRAINTS should be used in the rear seat whenever possible. If they must be used in the front passenger seat, move the seat to the full rear position. Failure to do so could kill or cause serious injuries to the child.
  • Page 94 94 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS The air bags will operate only when the ignition switch is in the ‘‘ON’’ or ‘‘START’’ position. When an impact sensor detects a front or side impact of sufficient force, it automatically ignities materials in the module inflator which generate gas and inflates the appropriate air bags.

  • Page 95: Event Data Recording

    SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 95 Driver’s and passenger’s front air bag system WARNING! • Air bags inflate very quickly and with great force. In certain situations, contact with an inflating air bag may cause small cuts, abrasions, and bruises. Event Data Recording Your vehicle is equipped with an ‘‘EDR’’...
  • Page 96 96 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS WARNING! • Do not set anything on, or attach anything to, the instrument panel above the glove compartment. Such items could strike and injure an occupant if the air bag inflates. •...
  • Page 97 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 97 Side air bag system (if so equipped) G28L0160 A label is attached to the seatbacks in vehicles with side air bags. The side air bags (A) are contained in the driver and front passenger seatbacks.
  • Page 98 98 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS WARNING! • The side air bags are designed to supplement the driver and front passenger seat belts in certain side impacts. Seat belts should always be worn properly, and the driver and front passenger should sit well back and upright in their seats without leaning against the window or door.
  • Page 99 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 99 WARNING! WARNING! • In order to reduce risk of injury from a deploying • Never install a rear-facing child restraint in the front passenger seat. Rear-facing child restraints MUST side air bag, do not allow any rear seat passengers ONLY be used in the rear seat.

  • Page 100: Srs Servicing

    100 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS working properly. The SRS warning light is shared by the SRS warning light driver’s air bag, the front passenger’s air bag, and the optional side air bags. The air bags will operate only when the ignition switch is in the ‘‘ON’’...
  • Page 101 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS 101 WARNING! WARNING! • Any maintenance performed on or near the com- • On vehicles with side air bags, do not modify ponents of the SRS should be performed only by your front seats, center pillar or center console. an authorized dealer.

  • Page 102: Transporting Pets

    102 SEATS, SEAT BELTS, CHILD RESTRAINTS AND AIR BAGS • If you decide to junk or scrap your vehicle, we urge Transporting Pets you to first take it to an authorized dealer so that the Airbags deploying in the front seat could harm your pet. SRS can be made safe for disposal.
  • Page 103 INSTRUMENTS AND CONTROLS CONTENTS Instrument cluster ..... . 106 Anti-lock braking system warning light (if so equipped) ..... . . 113 Meter cluster .
  • Page 104 104 INSTRUMENTS AND CONTROLS Changing the setting for warning operation . . . 118 Hazard warning flasher switch ... . 124 Instrument panel light dimmer control ..125 Automatic transaxle indicator (if so equipped) .

  • Page 105: Instruments And Controls 105

    INSTRUMENTS AND CONTROLS 105 Canadian Programming/Gate Programming. . . 135 Reprogramming a Signal Button ... 136 Operation ......136...

  • Page 106: Instrument Cluster

    106 INSTRUMENTS AND CONTROLS 6. Trip odometer INSTRUMENT CLUSTER 7. Trip odometer reset button D01A1960 Meter cluster 1. Fuel gauge 2. Tachometer 3. Speedometer 4. Engine coolant temperature gauge 5. Odometer...

  • Page 107: Indicator And Warning Light Package

    INSTRUMENTS AND CONTROLS 107 D50A439D Indicator and warning light package 5. Supplemental Restraint System (SRS) - air bag warning light →P. 116 1. Washer fluid level indicator →P. 119 6. Seat belt reminder/warning light →P. 118 2. Anti-lock braking system warning light (if so equipped) →P.

  • Page 108: Speedometer

    108 INSTRUMENTS AND CONTROLS 11. High beam indicator →P. 112 Tachometer 12. Cruise control indicator →P. 113 2.4 liter 3.0 liter engine engine 13. Theft-alarm indicator →P. 112 14. Malfunction indicator light (SERVICE ENGINE SOON) →P. 115 15. Oil pressure warning light →P. 114 16.

  • Page 109: Fuel Gauge

    INSTRUMENTS AND CONTROLS 109 Fuel gauge CAUTION! The red zone indicates an engine speed in excess of safe operation. Select the correct gear to control engine speed so the tachometer indicator does not enter the red zone. D05A0430 The gauge shows the amount of fuel in the fuel tank when the ignition key is turned to the ‘‘on’’...

  • Page 110: Odometer/Trip Odometer

    110 INSTRUMENTS AND CONTROLS 3. Reset button Odometer/Trip odometer D03F0320 D03F0120 When the ignition switch is turned to the “ON” position, ODO --- Odometer an “ODO” or “TRIP” indication is given. The odometer indicates the total distance the vehicle has Every time the reset button (3) is pressed lightly (less travelled.

  • Page 111: Engine Coolant Temperature Gauge

    INSTRUMENTS AND CONTROLS 111 Trip can be used to measure the distance traveled since the current trip began and Trip can be used to measure the distance from an intermediate location. To return either Trip or Trip display to zero, press the reset button (3) for more than one second.

  • Page 112: Turn Signal Indicators/Hazard Warning Lights

    112 INSTRUMENTS AND CONTROLS Theft-alarm indicator CAUTION! When the theft-alarm system has been armed, the indicator located in the instru- While driving, care should always be taken to main- ment cluster will illuminate and go off in 20 tain normal engine operating temperature. If the seconds, indicating the system is armed.

  • Page 113: Anti-Lock Braking System Warning Light (If So Equipped)

    INSTRUMENTS AND CONTROLS 113 Trunk-ajar warning light and chime 2. If the light does not go out or if it illuminates again, the anti-lock braking system is not functioning, and only This light illuminates when the trunk lid is the standard braking system is functioning. open or not completely closed.

  • Page 114: Front Fog Light Indicator

    114 INSTRUMENTS AND CONTROLS CAUTION! CAUTION! Do not drive with an extremely low fuel level; If the charging light remains on after the engine has running out of fuel could cause damage to the started, the battery charging system may be malfunc- catalytic converter.

  • Page 115: Malfunction Indicator Light (Service Engine Soon)

    INSTRUMENTS AND CONTROLS 115 Malfunction indicator light CAUTION! (SERVICE ENGINE SOON) • If this light illuminates and the engine oil level is This light is part of an onboard diagnostic (OBD) system which monitors the emis- not low, have your vehicle checked at an autho- rized dealer.

  • Page 116: Supplemental Restraint System (Srs)-Air Bag Warning Light

    116 INSTRUMENTS AND CONTROLS Overheating warning light CAUTION! If the warning light illuminates while the • Prolonged driving with the malfunction indicator engine is running, it is possible that the light on may result in further damage to the engine is overheated. emission control system.

  • Page 117: Brake Warning Light

    INSTRUMENTS AND CONTROLS 117 driving, take your vehicle to your authorized dealer and If the brake warning light illuminates while driving, it have the system checked. could mean braking performance deterioration. Park [See “Supplemental Restraint System (SRS)” on page your vehicle in a safe place using the following proce- 116.] dures: Brake warning light...

  • Page 118: Seat Belt Reminder/Warning Light

    118 INSTRUMENTS AND CONTROLS 3. With the seat belt still fastened, confirm that the Seat belt reminder/warning light A chime and warning light are used to warning light goes off. remind the driver to fasten the seat belt. 4. Within 1 minute of seeing the warning light go off, When the ignition key is turned to the remove the plate from the buckle and re-insert it 3 times.

  • Page 119: Automatic Transaxle Indicator (If So Equipped)

    INSTRUMENTS AND CONTROLS 119 Washer fluid level indicator WARNING! This light will illuminate and the chime will sound when the windshield washer level is In order to reduce risk of serious or fatal injury in an low. (approximately 0.1 gal/0.4 L) When accident, always wear your own seat belt, and do not the light comes on, add fluid.

  • Page 120: Combination Headlights, Dimmer And Turn Signal Lever

    120 INSTRUMENTS AND CONTROLS NOTE: Do not leave the headlights and other lamps on COMBINATION HEADLIGHTS, DIMMER AND TURN SIGNAL LEVER for a long time while the engine is not running. A discharged battery could result. Headlights Light auto-cutout feature (headlights, fog lights, etc.) 1.

  • Page 121: Headlight Reminder Chime

    INSTRUMENTS AND CONTROLS 121 1. Rotate the ignition key to “LOCK” or “ACC” position Headlight flasher (high/low beam) with the light switch in the ON “ ” position. 2. Turn light switch to “OFF” position within about 45 seconds of ignition key removal. 3.

  • Page 122: Dimmer (High/Low Beam Change)

    122 INSTRUMENTS AND CONTROLS NOTE: The headlights can also flash when the light Turn signals switch is OFF. If you turn the lights off with the headlights set to high-beam illumination, the headlights are automati- cally returned to their low-beam setting when the light switch is next turned to the ON “...

  • Page 123: (Headlights, Fog Lights, Etc.)

    INSTRUMENTS AND CONTROLS 123 There may be occasions when the lever does not return FOG LIGHT SWITCH after cornering. This typically occurs when the steering wheel is turned only slightly. In this case, return the lever by hand. The instrument cluster indicator will flash to indicate proper operation of the front and rear turn signal lights.

  • Page 124: Hazard Warning Flasher Switch

    124 INSTRUMENTS AND CONTROLS Press the flasher switch and the front and rear turn NOTE 1. If the headlights are switched to high beam, the fog signals will flash intermittently, as the hazard warning lights will go out; they will illuminate again when the lights.

  • Page 125: Instrument Panel Light Dimmer Control

    INSTRUMENTS AND CONTROLS 125 INSTRUMENT PANEL LIGHT DIMMER CONTROL ELECTRIC REAR WINDOW DEFROSTER Bright Indicator E15A0380 E17A0450 The brightness of the instrument panel lights can be The electric rear window defogger can be operated when adjusted by turning this knob while the light switch is in the ignition key is in the “ON”...

  • Page 126: Windshield Wipers

    126 INSTRUMENTS AND CONTROLS It will turn off automatically in about 17 minutes. WINDSHIELD WIPERS To turn off the defogger before 17 minutes has lapsed, push the switch again. CAUTION! • The rear window defroster is not designed to melt snow.

  • Page 127: Intermittent Wipers

    INSTRUMENTS AND CONTROLS 127 The intermittent intervals are adjustable from approxi- For maximum delay between wipes, rotate the knob mately 3 to 18 seconds by rotating the adjusting knob at toward you. To shorten the delay, rotate the knob away the end of the stalk.

  • Page 128: Windshield Washer

    128 INSTRUMENTS AND CONTROLS WINDSHIELD WASHER PRECAUTIONS TO OBSERVE WHEN USING WIPERS AND WASHERS CAUTION! If the washer is used in cold weather, the washer fluid sprayed onto the glass might freeze, resulting in poor visibility. Heat the glass with the defroster before using the washer.

  • Page 129: Dome Light

    INSTRUMENTS AND CONTROLS 129 vehicle in a safe place, turn off the ignition, and clean the DOME LIGHT deposits from the glass so that the wipers operate Type 1 smoothly. 4. Avoid using the washer for more than 20 seconds at a time.

  • Page 130: Lights (Dome Lights, Etc.) Auto-Cutout Function

    130 INSTRUMENTS AND CONTROLS LIGHTS (DOME LIGHTS, ETC.) AUTO-CUTOUT FUNCTION If any of the interior lights is left on with the ignition key in the ‘‘LOCK’’ position, the light goes off automatically after approximately 30 minutes to prevent the battery from running down.

  • Page 131: Reading Lights

    INSTRUMENTS AND CONTROLS 131 READING LIGHTS E19A1280 G08C0070 NOTE: • If the reading lights are left on for prolonged periods of 1. Driver’s side time with the engine turned off, the battery will be 2. Passenger’s side discharged (run down). Push the right or left reading light switch (lens) to turn on the light.

  • Page 132: Rear Personal Lights

    132 INSTRUMENTS AND CONTROLS REAR PERSONAL LIGHTS HORN SWITCH E19A1270 E23A0020T ON - The light illuminates Pressing on or around the mark on the steering wheel, OFF - The light illuminates when a door is opened and causes the horn to honk. goes out when it is closed.

  • Page 133: Training The Universal Transceiver

    INSTRUMENTS AND CONTROLS 133 equipped). The transmitter operates off your vehicle’s Training The Universal Transceiver battery and charging system; no batteries are needed. For best results, install a new battery in the hand held transmitter before programming. If your garage door For additional information on HomeLink , call toll-free opener (located in the garage) is equipped with an for customer assistance at 1–800–355–3515, or on the...
  • Page 134 134 INSTRUMENTS AND CONTROLS Release the buttons when the light in the indicator (D) 3. Choose one of the three buttons to train. Place the begins to flash after 20 seconds. hand held transmitter 1 to 3 inches from the universal transceiver while keeping its indicator light in view.
  • Page 135 INSTRUMENTS AND CONTROLS 135 NOTE: Canadian Programming/Gate Programming • Some entry gates and garage door openers may re- Canadian frequency laws, and the technology of some quire you to replace step 4 with the procedures listed entry gates, require you to press and release the hand under Canadian Programming.
  • Page 136 136 INSTRUMENTS AND CONTROLS To check if your device is protected by a “Rolling Code” Operation Press and hold the desired button (A, B or C) on the system: universal transceiver until the garage door or other • Check the owner’s manual for the device for mention device begins to operate.
  • Page 137 INSTRUMENTS AND CONTROLS 137 3. Return to the universal transceiver in the vehicle and firmly press and release the universal transceiver button (A, B or C). Press and release the button a second time to complete the training process. Some garage door openers may require you to do this procedure a third time to complete the training.
  • Page 138 138 INSTRUMENTS AND CONTROLS 2. When the indicator light (D) begins to flash slowly (after 20 seconds) position the hand held transmitter (E) 1 to 3 inches away from the universal transceiver button to be trained. 3. Press and hold the hand held transmitter button. 4.
  • Page 139 INSTRUMENTS AND CONTROLS 139 This device complies with FCC rules part 15. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interference that may cause undes- ired operation.
  • Page 141 STARTING AND DRIVING CONTENTS Break-in recommendations....144 Ignition switch ......149 Fuel selection .
  • Page 142 142 STARTING AND DRIVING Gear positions ......156 Recommended downshifting speed ..169 Driving speed Driving precautions .
  • Page 143 STARTING AND DRIVING 143 Cruise/speed control ....189 Lights ......200 To activate.

  • Page 144: 144 Starting And Driving

    144 STARTING AND DRIVING BREAK-IN RECOMMENDATIONS FUEL SELECTION Advanced automobile manufacturing techniques permit Your vehicle is designed to use unleaded gasoline only. It you to operate your new vehicle without experiencing a is equipped with a fuel filler tube especially designed to long break-in period of low-speed driving.

  • Page 145: Gasoline Additives

    STARTING AND DRIVING 145 3.0 liter engine model CAUTION! Your vehicle is designed to operate on regular grade unleaded gasoline having a minimum octane rating of 87 Using leaded gasoline in your vehicle will damage [(MON+RON)/2], or 91 RON. If optimum performance the engine, catalytic converter, and the oxygen sen- is wanted, it is recommended to use premium grade sors.

  • Page 146: Gasoline/Oxygenate Blends

    146 STARTING AND DRIVING Gasoline/Oxygenate Blends MMT in Gasoline Some fuel suppliers blend unleaded gasoline with mate- MMT is a manganese containing metallic additive that is rials called oxygenates such as 10% ethanol, MTBE and blended into some gasoline to increase the octane num- ETBE.

  • Page 147: Materials Added To Fuel

    STARTING AND DRIVING 147 states adopting California emission standards, your ve- Materials Added to Fuel hicle will operate satisfactorily on fuels meeting Federal All gasoline sold in the United States is required to specifications, but emission control system performance contain effective detergent additives. Use of additional may be adversely affected.
  • Page 148 148 STARTING AND DRIVING NOTE: Tighten the gas cap until you hear a “clicking” CAUTION! sound. This is an indication that the gas cap is properly tightened. Damage to the fuel system or emission control system could result from using an improper fuel The Malfunction Indicator Light (“SERVICE ENGINE tank filler tube cap (gas cap).

  • Page 149: Fuel Economy

    STARTING AND DRIVING 149 FUEL ECONOMY IGNITION SWITCH Fuel economy is dependent on many factors. Your per- sonal driving habits can have a significant effect on your fuel economy. Several recommendations for achieving maximum fuel economy are listed below. 1. When pulling away from traffic lights or stop signs, accelerate slowly and smoothly.

  • Page 150: Key Reminder Chime

    150 STARTING AND DRIVING NOTE: For vehicles with an automatic transaxle, the key CAUTION! cannot be removed unless the selector lever is set to the • Do not remove the ignition key from the ignition “P” (PARK) position. switch while driving. The steering wheel will lock, causing loss of control.

  • Page 151: Theft Protection

    STARTING AND DRIVING 151 THEFT PROTECTION CAUTION! If your vehicle needs to be towed, turn the key to the CAUTION! ACC position to unlock the steering wheel. Always remove the key from the ignition switch and lock all doors when leaving the vehicle unattended. STARTING Always try to park your vehicle in a well lighted Tips for starting...

  • Page 152: Normal Conditions

    152 STARTING AND DRIVING Normal conditions WARNING! The starting procedure is as follows: Never run the engine in a closed or poorly ventilated 1. Insert the ignition key and make sure all occupants are area any longer than is needed to move your vehicle properly seated with seat belts fastened.

  • Page 153: Flooded Engine

    STARTING AND DRIVING 153 NOTE: Slight noises may be heard on engine start-up. AUTOMATIC TRANSAXLE (IF SO EQUIPPED) These noises will disappear as you continue warming up The automatic transaxle is designed for optimum control the engine. and equipped with adaptive control capabilities. The electronically controlled transaxle optimally matches Flooded engine gear shifts to almost all driving and road conditions.

  • Page 154: Selector Lever Operation

    154 STARTING AND DRIVING Selector lever operation CAUTION! As an additional safety precaution, models equipped with an automatic transaxle have a shift-lock device that The electronically controlled transaxle system is holds the selector lever in the “P” (PARK) position. To strictly intended to provide supplementary func- move the selector lever from the “P”...
  • Page 155 STARTING AND DRIVING 155 WARNING! Always depress the brake pedal when shifting the selector lever into a gear from the “N” (NEUTRAL) position. When beginning to drive, do not shift the selector lever from the “N” (NEUTRAL) position while depressing the accelerator pedal; doing so may cause the vehicle to “jump”...

  • Page 156: Gear Positions

    156 STARTING AND DRIVING Gear positions WARNING! “P” PARK • Never move the lever to the “N” position while The “P” (PARK) position supplements the parking brake driving since you could accidentally move the by locking the transaxle while the vehicle is parked. lever into the P or R position, damaging the The engine can be started in this position.

  • Page 157: Driving Speed

    STARTING AND DRIVING 157 “3” THIRD / “2” SECOND Driving speed (Vehicles with automatic transaxle) For driving slowly in heavy city traffic or on mountain In order to avoid damage to the engine from excessively roads where more precise speed control is desired. high rpm, do not exceed the listed driving speed when Also use it when climbing long grades, and for engine the selector lever is set to the “3”...

  • Page 158: Transaxle Reset Mode

    158 STARTING AND DRIVING Transaxle Reset Mode AUTOMATIC TRANSAXLE AUTOSTICK The transaxle is monitored for abnormal conditions. If a (IF SO EQUIPPED) condition is detected that could cause damage, the trans- Designed for optimum control and equipped with adap- axle automatically shifts into second gear. The transaxle tive control capabilities, the electronically controlled remains in second gear despite the forward gear selected.

  • Page 159: Selector Lever Operation

    STARTING AND DRIVING 159 Selector lever operation CAUTION! The electronically controlled transaxle system is strictly intended to provide supplementary func- tions. When driving downhill under certain condi- Main gate tions, or immediately after starting when the auto- matic transaxle is cold, no automatic shift-down may be made.
  • Page 160 160 STARTING AND DRIVING I04S1580 I04A1430 In the main gate, the selector lever has 4 positions and Button (A) must be pushed while the brake pedal is is equipped with a lock button (A) to prevent inad- depressed to move the selector lever. vertent selection of the wrong gear.

  • Page 161: Indicator Lights

    STARTING AND DRIVING 161 Indicator lights WARNING! Always depress the brake pedal when shifting the selector lever into a gear from the “N” (NEUTRAL) position. When beginning to drive, do not shift the selector lever from the “N” (NEUTRAL) position while depressing the accelerator pedal;...

  • Page 162: Selector Positions (Main Gate)

    162 STARTING AND DRIVING If the “N” indicator light in the instrument panel flashes, 2. The “N” indicator light flashes slowly (once per there could be a malfunction with the automatic transaxle second) in the “D” or “Autostick” range. system. Identify and take action in accordance with the The automatic transaxle safety device may be operating following procedures: due to a malfunction.

  • Page 163: Selector Positions Manual Gate Autostick

    STARTING AND DRIVING 163 “N” NEUTRAL Selector positions Manual gate Autostick The engine may be started in this position. Autostick is a driver-interactive transaxle that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine brak- WARNING! ing, eliminate undesirable upshifts and downshifts, and •...
  • Page 164 164 STARTING AND DRIVING CAUTION! • Upward shifts do not take place automatically in Autostick. The driver must execute upward shifts in accordance with road conditions, make sure the engine rpm remains below the red zone on the tachometer. • By rapidly moving the selector lever backwards (DOWN) twice, it is possible to skip one gear, (i.e.

  • Page 165: Holding On An Upgrade

    STARTING AND DRIVING 165 3. In Autostick, downward shifts are made automatically Indication lights when the vehicle slows down. When the vehicle stops, 1st gear is automatically selected. 4. When starting out on slippery roads, push the selector lever forward into the + (UP) position. This puts the transmission into 2nd gear and is better for starting out on slippery roads.

  • Page 166: Transaxle Reset Mode

    166 STARTING AND DRIVING Transaxle Reset Mode MANUAL TRANSAXLE (IF SO EQUIPPED) The transaxle is monitored for abnormal conditions. If a condition is detected that could cause damage, the trans- axle automatically shifts into second gear. The transaxle remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate.

  • Page 167: To Start

    STARTING AND DRIVING 167 To start 2. To shift into reverse from 5th gear, move the gearshift Depress the clutch pedal fully and shift into 1st. Then lever to the “N” (NEUTRAL) position, and then shift into gradually release the clutch pedal while depressing the reverse.
  • Page 168 168 STARTING AND DRIVING At low altitude locations, shift at the vehicle speeds listed In high altitude locations, it should be upshifted as listed for acceleration. Earlier upshifts during cruise conditions below. (relatively steady speeds) will result in increased fuel Condition Upshift speeds mph (km/h) economy.

  • Page 169: Recommended Downshifting Speed

    STARTING AND DRIVING 169 Recommended downshifting speed Possible driving speed Condition 2.4 liter engine 3.0 liter engine Downshifting speed Vehicles with Vehicles with Condition mph (km/h) 205/60R16 215/50R17 3rd to 2nd tire tire Under 20 (30) 4th to 2nd 31 mph 34 mph (55 km/h) 5th to 2nd (50 km/h)
  • Page 170 170 STARTING AND DRIVING up on the parking brake lever. Push the release button and lower the lever fully. I07A0020 Before leaving the vehicle, make sure that the parking I07A0030 brake is set. To set the parking brake, pull up firmly on the lever.

  • Page 171: Brake Pedal

    STARTING AND DRIVING 171 You should always apply the parking brake before leav- BRAKE PEDAL ing the vehicle. Excessive use of the brake can cause fading, resulting in poor brake response and premature wear of brake lin- ings. WARNING! When driving down a long or steep grade, use engine •...

  • Page 172: Power Brakes

    172 STARTING AND DRIVING by increased pedal travel during application, greater WARNING! pedal force required to slow or stop, and activation of the Brake Warning Lamp during brake use. Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally WARNING! high brake temperatures, excessive lining wear, and...

  • Page 173: Anti-Lock Braking (Abs) System (If So

    STARTING AND DRIVING 173 accident. Pumping makes the stopping distance longer. WARNING! Just press firmly on your brake pedal when you need to slow down or stop. Driving on worn brake pads can reduce your ability to stop, and can result in an accident. General driving hints (standard/anti-lock brakes) 1.
  • Page 174 174 STARTING AND DRIVING CAUTION! • Anti-lock braking system can not prevent acci- dents. It remains the driver’s task to exercise safety precautions and to drive prudently. • To prevent failure of the anti-lock braking system, be sure all 4-wheels and tires are the same size and type (space saver spare excluded).

  • Page 175: Steering Wheel Tilt Lock Lever

    STARTING AND DRIVING 175 6 mph (10 km/h). It stops operating when the vehicle STEERING WHEEL TILT LOCK LEVER decelerates to a speed below approximately 3 mph (5 km/h). Unlock Lock Wheel speed G09A0270 sensor To adjust the steering wheel height, release the tilt lock lever while raising or lowering the steering wheel to the I24A0060 desired height.

  • Page 176: Power Steering

    176 STARTING AND DRIVING WARNING! WARNING! • After adjustment, to the desired height, check to Never turn off the engine while the vehicle is be sure that the lever is locked. moving. Your ability to control the vehicle may be seriously reduced.

  • Page 177: Inside Day/Night Rearview Mirrors

    STARTING AND DRIVING 177 INSIDE DAY/NIGHT REARVIEW MIRRORS WARNING! • Do not attempt to adjust the rearview mirrors while driving. This can be dangerous. • Your passenger’s side mirror is convex. The ob- jects you see in the mirror will look smaller and farther away than they actually are.

  • Page 178: Electrochromic Inside Rearview Mirror (If So Equipped)

    178 STARTING AND DRIVING I08A0630 I08A0640 Electrochromic inside rearview mirror (if so equipped) When the ignition key is in the “ACC” or “ON” position, the green indicator (A) should be illuminated. If not, press the display switch (C) for more than 6 seconds, less than 9 seconds, until the indicator illuminates.

  • Page 179: Electrochromic Mirror Operation (If So Equipped)

    STARTING AND DRIVING 179 To turn off the function, press the display switch (C) more than 6 seconds, less than 9 seconds. When the green indicator (A) goes off, the automatic anti-glare will not function. To turn the function back on, press the display switch (C) more than 6 seconds, less than 9 seconds.
  • Page 180 180 STARTING AND DRIVING 1. When the ignition key is “ACC” or “ON” position, How to change the display mode automatic anti-glare operate and current outside tem- The mode will change in order by pressing the display perature and compass are displayed. switch for the following seconds.
  • Page 181 STARTING AND DRIVING 181 2. If you press the display switch less than 3 seconds, you 3. If you press the display switch more than 3 seconds, can turn on/off the display. less than 6 seconds, you can alternate the temperature reading between Fahrenheit and Celsius.
  • Page 182 182 STARTING AND DRIVING 4. If you press the display switch more than 6 seconds, 5. If you press the display switch more than 9 seconds, less than 9 seconds, you can turn on/off the automatic less than 12 seconds, you can adjust for compass vari- anti-glare.
  • Page 183 STARTING AND DRIVING 183 6. If you press the display switch more than 12 seconds, Outside temperature (if so equipped) you can recalibrate compass variance. →188 I08A0600 I08A0590 When the ignition key is in the “ACC” or “ON” position, the current outside temperature is displayed.
  • Page 184 184 STARTING AND DRIVING To alternate the temperature reading between NOTE Fahrenheit and Celsius • The outside temperature can be displayed from -40°F (-40°C) • If the outside temperature is below -40°F (-40°C) or over 140°F (60° C) an error message “SC” or “OC” will be shown in the display.
  • Page 185 STARTING AND DRIVING 185 Compass operation and true geographic north. If not adjusted to account for magnetic variation of compass, your compass could give false readings. To adjust for magnetic variation of compass 1. Press the display switch more than 9 seconds, less than 12 seconds.
  • Page 186 186 STARTING AND DRIVING 2. Find your current location and variance zone number NOTE on the zone map. • Do not attach ski racks, antennas, or any other object to the vehicle by means of a magnet. Such magnets will affect the operation of the compass. •...
  • Page 187 STARTING AND DRIVING 187 To calibrate the compass If the display reads “CAL” (A), there may be a strong magnetic field interfering with the compass. In this case, the compass may need calibration. I08A0650 D11C0110 If the “CAL” is displayed, drive the vehicle in a circle at about 5 mph (8km/h) or less until the “CAL”...
  • Page 188 188 STARTING AND DRIVING If the “CAL” is not displayed, but compass calibration is Electric remote-controlled outside mirrors required, press and hold the display switch for 12 sec- onds, or until “CAL” is displayed. With “CAL” dis- played, drive the vehicle in a circle at less than 5mph (8km/h) or less until the “CAL”...

  • Page 189: Cruise/Speed Control

    STARTING AND DRIVING 189 NOTE CRUISE/SPEED CONTROL • After adjustment, return the lever to the centered position. Press the left, right, up or down switches (B) to adjust the mirrors as desired. 1. Up 2. Down 3. Right 4. Left I10A1190 Cruise/speed control is an automatic speed control sys- tem.

  • Page 190: To Activate

    190 STARTING AND DRIVING • Your speed may increase to more than the set speed CAUTION! on a steep downhill. You must use the brake to control your speed. If your speed increases too • For safety reasons, the main switch (A) should be much, turn off the cruise/speed control.
  • Page 191 STARTING AND DRIVING 191 2. When the main switch (A) is ON, the “CRUISE” 3. Pull the lever (B) down while driving at the desired control light on the instrument cluster will illuminate. speed. I10A1670 I10A1500 To increase the set speed There are 2 ways to increase the set speed.
  • Page 192 192 STARTING AND DRIVING Cruise/speed control lever Accelerator I10A1530 I10A1550 Pull the cruise/speed control lever up and hold it. Your Press the accelerator pedal to reach your desired speed. speed will then gradually increase. When you reach your Pull the cruise/speed control lever down for a moment, desired speed, release the switch.
  • Page 193 STARTING AND DRIVING 193 Cruise/speed control lever Brake pedal I10A1540 I10A1110 Pull the cruise/speed control lever down and hold it Press the brake pedal (which disengages the cruise/ while driving at the set speed, and you will slow down speed control), then pull the cruise/speed control lever (coast) gradually.

  • Page 194: To Deactivate

    194 STARTING AND DRIVING To accelerate for passing To deactivate I10A1520 I10A1510 Press the accelerator pedal as you would normally. When The cruise/speed control can be turned off as follows: you release the pedal, the cruise/speed control will 1. Push the main switch (A) at the end of the lever (Main return to your set speed.

  • Page 195: To Resume The Set Speed

    STARTING AND DRIVING 195 3. By slightly tapping the brake pedal or pressing down To resume the set speed on it to slow your speed. 4. By pressing the clutch pedal down (for vehicles with manual transaxle). 5. By moving the selector lever to “N” (for vehicles with automatic transaxle).

  • Page 196: Traction Control (If So Equipped)

    196 STARTING AND DRIVING procedure: Driving hints (1) The ignition key is turned OFF. 1. Traction control system does not actively apply brakes. (2) The main switch is turned OFF. Always decelerate the vehicle sufficiently before entering corners or bends. TRACTION CONTROL (IF SO EQUIPPED) On slippery surfaces, traction control system prevents the 2.

  • Page 197: Catalytic Converter

    STARTING AND DRIVING 197 Warning light CAUTION • If the warning light illuminates, a malfunction may have occurred in the system. When this happens, have your vehicle checked at an authorized dealer. CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only.
  • Page 198 198 STARTING AND DRIVING To minimize the possibility of catalytic converter dam- CAUTION! age: Damage to the catalytic converter can result if your 1. Use UNLEADED GASOLINE ONLY of the type rec- vehicle is not kept in proper operating condition. In ommended in “Fuel selection”.

  • Page 199: Vehicle Preparation Before Driving

    STARTING AND DRIVING 199 8. Stop driving the vehicle if you think the performance Seat belts and seats is noticeably less, or that there is unnecessary engine 1. Before starting the vehicle, make certain that you and miss, or any other engine trouble, such as with the all your passengers are seated and properly wearing the ignition, etc.

  • Page 200: Lights

    200 STARTING AND DRIVING Check wheel nuts for tightness and tires (including spare SAFE DRIVING TECHNIQUES tire) for proper pressure. Maintain specified tire inflation Even this vehicle’s safety equipment, and your safest pressures. Replace tires before they are excessively worn. driving, cannot guarantee that you can avoid accident or injury.

  • Page 201: Driving, Alcohol And Drugs

    STARTING AND DRIVING 201 6. Always obey applicable laws and regulations. Be a Similarly, prescription and nonprescription drugs affect courteous and alert driver. your alertness, perception and reaction time. Consult Always leave room for unexpected events, such as sud- with your doctor or pharmacist. den braking.

  • Page 202: Operation During Cold Weather

    202 STARTING AND DRIVING over curbs or parking stop blocks. Always use caution WARNING! when traveling up or down sharp inclines as your bumper may contact the road surface. The battery gives off explosive hydrogen gas. Any spark or flame can cause the battery to explode, 2.

  • Page 203: Trailer Towing

    STARTING AND DRIVING 203 The trailer tongue load must be considered as part of the WARNING! tow vehicle load capacity when loading the vehicle. Never open the radiator cap when the radiator is hot. NOTE: Check the automatic transmission fluid level You could be seriously burned.
  • Page 204 204 STARTING AND DRIVING Weight limits I26A1290 Never exceed the maximum trailer weight (A), maximum tongue weight (B), Gross Vehicle Weight Rating (GVWR) and Gross Axle Weight Rating (GAWR).
  • Page 205 FOR PLEASANT DRIVING CONTENTS Sun visors ......209 Weak reception (fading) ....217 To adjust the sun visor position .
  • Page 206 206 FOR PLEASANT DRIVING Fade ......220 Noise Reduction ..... . 223 Graphic Equalizer .
  • Page 207 FOR PLEASANT DRIVING 207 Tuning ......226 Time Button ......228 Balance .
  • Page 208 208 FOR PLEASANT DRIVING Vents....... . 235 How to use the controls ....244 Air flow rate and direction adjustments .

  • Page 209: For Pleasant Driving 209

    FOR PLEASANT DRIVING 209 SUN VISORS To adjust the sun visor position 1. Remove the holder (A) from the hook (B), then move the sunvisor to the window. 2. Slide the sun visor and adjust the position. G10A0260 1. To reduce front glare. 2.

  • Page 210: Vanity Mirror

    210 FOR PLEASANT DRIVING Vanity mirror A vanity mirror is on the back of the sun visor. G10A0580 WARNING! G13A0850 • Do not attempt to adjust the sun visor while driving. This can be dangerous.

  • Page 211: Accessory Socket

    FOR PLEASANT DRIVING 211 ACCESSORY SOCKET G13A0840 G38A0710 Opening the the lid of the vanity mirror will automati- cally turn on the mirror lights (C). Two accessory sockets are provided in the center console. To use a “plug-in” type accessory, insert it in the socket. CAUTION! The accessory socket (A) can be operated when the ignition key is in the “ON”...

  • Page 212: Cup Holder

    212 FOR PLEASANT DRIVING CUP HOLDER CAUTION! • Be sure to use a “plug-in” type accessory operat- ing on 12V and at 120W or less. Extended use of electronic equipment with the engine off may run down the battery. • When the accessory socket is not in use, be sure to close the socket cap.

  • Page 213: Accessory Boxes

    FOR PLEASANT DRIVING 213 ACCESSORY BOXES CAUTION! Do not drink beverages while driving the vehicle; doing so could distract you and result in an accident. G14A0840 Convenient storage space is located throughout the ve- hicle. 1. Door pockets G34H0870 2. Center console REAR SEAT Cup holders are provided at each side for the rear 3.

  • Page 214: Glove Compartment

    214 FOR PLEASANT DRIVING Glove compartment WARNING! An open glove compartment door can result in serious injury to the front passenger in an accident, even if the passenger is wearing the seat belt. Al- ways keep the glove compartment door closed when driving.

  • Page 215: Center Console With Lid

    FOR PLEASANT DRIVING 215 Center console with lid Trunk net (if so equipped) G14C0430 G17E0270 Small articles can be stored in center console. Attach the net to hooks according to the illustration. Keep To open the center console, pull up on the front of the lid. the net stored in the trunk so it can be used at any time.

  • Page 216: Electronic Digital Clock

    216 FOR PLEASANT DRIVING ELECTRONIC DIGITAL CLOCK GENERAL INFORMATION ABOUT YOUR RADIO The clock and radio each use the display panel built into the radio. A digital readout indicates the time in hours and minutes whenever the ignition switch is in the ON or ACC position.

  • Page 217: Signal Transmission

    FOR PLEASANT DRIVING 217 Signal transmission Reflections FM signals do not follow the earth’s surface nor are they reflected by the upper atmosphere. For this reason, FM broadcasts cannot be received over long distances. AM signals follow the earth’s surface and are reflected by the upper atmosphere.

  • Page 218: Cross Modulation

    218 FOR PLEASANT DRIVING The direct signal from the broadcast station reaches the FM stereo reception antenna slightly before the reflected signal. This time Stereo reception requires a very high broadcast signal quality. This means that disturbances mentioned previ- difference may cause some reception disturbance or ously become more marked and the reception range is flutter.

  • Page 219: Whip Antenna

    FOR PLEASANT DRIVING 219 FM reception is not as sensitive to electrical disturbances CAUTION! as AM. AM reception is sensitive to electrical distur- bances such as power lines, lightning and other types of It is recommended to remove the whip antenna similar electrical phenomena.

  • Page 220: Power Switch, Volume Control

    220 FOR PLEASANT DRIVING Power Switch, Volume Control Fade Press the ON/VOL control to turn the radio on. Turn the The Fade control provides for balance between the front volume control clockwise to increase the volume. and rear speakers. Push in the button and it will pop out. Adjust the balance and push the button back in.

  • Page 221: To Set The Radio Pushbutton Memory

    FOR PLEASANT DRIVING 221 To stop the search, press SCAN a second time. 1. This device may not cause harmful interference, To Set The Radio Pushbutton Memory 2. This device must accept any interference received, When you are receiving a station that you wish to including interference that may cause undesired opera- commit to push-button memory, press the SET button.

  • Page 222: Seek Button

    222 FOR PLEASANT DRIVING Seek Button Tape Eject Press the SEEK button up for the next selection on the Press the EJT Tape button and the cassette will disengage tape and down to return to the beginning of the current and eject from the radio.

  • Page 223: Noise Reduction

    FOR PLEASANT DRIVING 223 Noise Reduction If the volume control is ON, the unit will switch from The Dolby noise reduction system* is on whenever the radio to CD mode and begin to play when you insert the tape player is on, but may be switched off. disc.

  • Page 224: Program Button 4 (Random Play)

    224 FOR PLEASANT DRIVING released. Press the RW (Rewind) button and the CD CASSETTE TAPE AND PLAYER MAINTENANCE player will reverse through the tracks until the button is To keep the cassette tapes and player in good condition, released. take the following precautions: 1.

  • Page 225: Am/Fm Stereo Radio With 4 Disc Cd Changer (If So Equipped)

    FOR PLEASANT DRIVING 225 Maintain your cassette tape player. The head and capstan AM/FM STEREO RADIO WITH 4 DISC CD shaft in the cassette player can pick up dirt or tape CHANGER (IF SO EQUIPPED) deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport.

  • Page 226: Seek Button (Radio Mode)

    226 FOR PLEASANT DRIVING Seek Button (Radio Mode) Tone Control Press and release the Seek button to search for the next The unit has 2 separate controls for bass and treble. Each station in either the AM or FM mode. Press the top of the is controlled by a slider control with a detent at the mid button to seek up and the bottom to seek down.

  • Page 227: To Set The Pushbutton Memory

    FOR PLEASANT DRIVING 227 To Set The Pushbutton Memory General Information When you are receiving a station that you wish to commit This radio complies with Part 15 of FCC rules and with to push-button memory, press the SET button. SET 1 will RS-210 of Industry Canada.

  • Page 228: Seek Button

    228 FOR PLEASANT DRIVING will show the track number and index time in minutes button to go back to the beginning of the track. Press and seconds. Play will begin at the start of track 1. button for a second time to stop Random Play. Seek Button Radio/CD Button Press the top of the SEEK button for the next selection on...

  • Page 229: Playing Discs

    FOR PLEASANT DRIVING 229 Playing Discs STEERING WHEEL REMOTE CONTROL The radio display indicates the CD number (the slot SWITCHES (IF SO EQUIPPED) where the CD is loaded), and the current track being played at the time. If more than one CD is loaded in the CD changer, it automatically plays the next CD after playing the last track of the current CD.

  • Page 230: How To Adjust The Volume

    230 FOR PLEASANT DRIVING 5. Seek down / Rewind APS button / Track down button To listen to the radio 6. Volume down button To select AM/FM mode Mode change button - 4 NOTE: • Do not push two or more of the steering wheel Select the desired band (AM or FM) by pressing this remote control switches at the same time.

  • Page 231: To Listen To A Tape

    FOR PLEASANT DRIVING 231 To listen to a tape To listen to a CD To operate the APS (Automatic Program Sensor) To select CD mode system Mode change button - 4 The start of each song on a prerecorded music tape can be Select the desired mode (CD player mode or CD au- found by using the Fast forward APS button (1) or tochanger mode) by pressing this button.

  • Page 232: Handling Of Compact Discs

    232 FOR PLEASANT DRIVING Handling of Compact Discs H12F0180 (1) Use only the type of compact discs that have the mark shown in the illustration above. (Playback of CD-R discs may cause problems. CD-RW discs cannot be played). (2) The use of special shaped, damaged compact discs (like cracked discs) or low-quality compact discs (like warped discs or burrs on the discs) such as those H12F0172...
  • Page 233 FOR PLEASANT DRIVING 233 (3) In the following circumstances, moisture can form on compact discs and inside the audio system, prevent- ing normal operation. • When there is high humidity (for example, when it is raining). • When the temperature suddenly rises, such as right after the heater is turned on in cold weather.

  • Page 234: Radio Operation And Cellular Phones

    234 FOR PLEASANT DRIVING Do not wipe in a circle. Never use any chemicals such compact disc that has stickiness or other contamina- as benzine, paint thinner, a disc spray cleaner, or an tion left by a peeled-off label, or sticker. If you use anti-static agent on the disc.

  • Page 235: Vents

    FOR PLEASANT DRIVING 235 This condition is not harmful to the radio. If your radio Air flow rate and direction adjustments performance does not satisfactorily “clear” by the repo- Center and side vents sitioning of the antenna, it is recommended that the radio volume be turned down or off during cellular phone operation.

  • Page 236: Air Conditioning

    236 FOR PLEASANT DRIVING Change the direction of the airflow from side to side by AIR CONDITIONING moving the knob (A). Change the vertical direction of the Control panel air flow up and down by pushing the top button edge of the vents.

  • Page 237: Changing The Blower Speed

    FOR PLEASANT DRIVING 237 Changing the blower speed Changing the temperature H23A2860 H23A2870 The blower may be operated (when the ignition key is in Select the desired temperature level by turning the tem- the ON position) at 4 different speeds. Select the best perature control dial either clockwise or counterclock- speed to fit your needs.

  • Page 238: Changing Mode Selection

    238 FOR PLEASANT DRIVING Changing mode selection Face position H03I0670 To change air flow to the different outlets, turn the mode selection dial to the desired position. H13D0543 Air flows exclusively to the upper part of the passenger compartment.
  • Page 239 FOR PLEASANT DRIVING 239 Foot/face position NOTE: Air flows mostly to the upper part of the pas- senger compartment with the dial within position (1), and flows mostly to the leg area with the dial within position (2). H13D0553 Air flows to the upper part of the passenger compart- ment and flows to the leg area.
  • Page 240 240 FOR PLEASANT DRIVING Foot position Foot/defroster position H13D0563 H13D0573 Air flows mainly to the leg area. Air flows to the leg area, windshield, and door windows.
  • Page 241 FOR PLEASANT DRIVING 241 NOTE: Air flows mostly to the leg area with the dial Defroster position within position (1), and flows mostly to the windshield with the dial within position (2). H13D0583 Air flows exclusively to the windshield and door win- dows.

  • Page 242: Changing Air Selection

    242 FOR PLEASANT DRIVING NOTE: When the mode selection dial is set to the “ ” remove fog or frost from the windshield. or “ ” position, the air conditioning compressor will When air conditioning is selected, the air selection will be operate automatically.

  • Page 243: Air Conditioning Switch

    FOR PLEASANT DRIVING 243 Air conditioning switch CAUTION! When using the air conditioning, the idle speed is slightly increased. Therefore, make sure your foot is firmly on the brake pedal when shifting the trans- mission to drive. For the 3.0 liter engine model, if the air conditioning indicator (A) blinks, it is suspected that something is wrong with the air conditioning.

  • Page 244: How To Use The Controls

    244 FOR PLEASANT DRIVING How to use the controls Defrosting or defogging of the windshield and door windows Heating CAUTION! For safety, make sure you have a clear view through all windows before driving. To remove frost or fog from the windshield and door windows, use the mode selection dial (“...
  • Page 245 FOR PLEASANT DRIVING 245 To keep the windshield and door windows defogged, For quick defrosting and to keep leg area heated (when driving in rain or 1. Set the mode selection dial to the position. snow). 1. Set the mode selection dial to the position.
  • Page 246 246 FOR PLEASANT DRIVING Combination of unheated air and heated air Cooling H03C0680 H04F0970 Set the mode selection dial to the position shown in the Set the mode selection dial to the “ ” position shown in illustration and set the air selection switch (A) to the the illustration.

  • Page 247: Important Operation Tips For Air Conditioning

    FOR PLEASANT DRIVING 247 Adjust the temperature by turning the temperature con- Important operation tips for air conditioning trol dial clockwise or counterclockwise. 1. Park the vehicle in the shade whenever possible. Select the desired blower speed. Parking under the hot sun makes the vehicle interior extremely hot, which requires more time to cool the interior.

  • Page 248: During A Long Period Of Disuse

    248 FOR PLEASANT DRIVING INSTALLATION OF ACCESSORIES CAUTION! CAUTION! The air conditioning system in your vehicle must be charged with the refrigerant HFC-134a and the lubri- Before any electrical or electronic accessories are cant SUN-PAG 56. installed, consult an authorized dealer. Use of any other refrigerant or lubricant will cause 1.
  • Page 249 VEHICLE CARE CONTENTS Cleaning the inside of your vehicle ..251 Polishing your vehicle ....256 Plastic, vinyl leather, fabric, and flocked parts.
  • Page 250 250 VEHICLE CARE In order to maintain the value and good looks of your CAUTION! vehicle, perform regular maintenance using proper ma- terials and procedures. Cleaning products can be dangerous. Some are poi- Be sure to use only those materials and procedures that sonous.

  • Page 251: Cleaning The Inside Of Your Vehicle

    VEHICLE CARE 251 CLEANING THE INSIDE OF YOUR VEHICLE 2. After using detergent, dip the cloth in fresh water and After cleaning the inside of your vehicle with cleaner, wring out well. Using this cloth, wipe off the detergent wipe it dry in a shady, well ventilated area. thoroughly.

  • Page 252: Genuine Leather (If So Equipped)

    252 VEHICLE CARE 6. The genuine leather surface may harden and shrink if Genuine leather (if so equipped) 1. Lightly wipe with a soft cloth soaked in a 5% solution it is exposed to the direct rays of the sun for long hours. of neutral detergent and water.

  • Page 253: Washing

    VEHICLE CARE 253 Washing CAUTION! Chemicals contained in the dirt and dust picked up from • When washing the under side of your vehicle, air, rain, snow, or road surface can damage the paint coat and body of your vehicle if left in prolonged contact. wear a pair of rubber gloves in order to protect Frequent washing and waxing is the best way to protect your hands.

  • Page 254: During Cold Weather

    254 VEHICLE CARE During cold weather CAUTION! Salt and other chemicals that are spread on winter roads • Some types of washers (including coin-operated in some geographical areas can have a detrimental effect on the vehicle underbody. You should flush the under- washers) apply high temperature and high pres- body with a high pressure hose every time you wash the sure to the vehicle, which may cause heat distor-...

  • Page 255: Waxing Your Vehicle

    VEHICLE CARE 255 Waxing your vehicle CAUTION! Wax your vehicle once or twice a year, or when painted • Waxes containing high abrasive compounds surfaces do not shed water well. Apply a small amount of wax to painted surfaces with a should not be used.

  • Page 256: Polishing Your Vehicle

    256 VEHICLE CARE Polishing your vehicle Cleaning plastic parts If painted surfaces have been severely damaged and lost Use a sponge or chamois. their original luster and color tone, polish the surface If vehicle wax adheres on the plastic bumper or mold- lightly with a fine polishing compound.

  • Page 257: Chrome Parts

    VEHICLE CARE 257 Chrome parts Window glass To prevent spots and corrosion of chrome parts, wash The window glass can be cleaned using only a sponge with water, dry thoroughly, and apply a nonabrasive and water. Glass cleaner can be used to remove wax, oil, automotive wax.
  • Page 259 EMERGENCIES CONTENTS If the vehicle breaks down ....261 Jacking and tire changing ....268 If the engine quits .
  • Page 260 260 EMERGENCIES Headlights (Type 1) ....292 Front fog light ......296 Headlights (Type 2) .

  • Page 261: If The Vehicle Breaks Down

    EMERGENCIES 261 IF THE VEHICLE BREAKS DOWN OPERATION UNDER ADVERSE DRIVING If the vehicle breaks down on the road, move to the CONDITIONS shoulder and activate the hazard warning flashers. If If your vehicle becomes stuck in sand, mud or there is no shoulder, or the shoulder is not safe, drive in snow the right lane, slowly, with the hazard flashers activated,...

  • Page 262: On A Wet Road

    262 EMERGENCIES On a wet road WARNING! When attempting to rock your vehicle out of a stuck CAUTION! position, be sure that the area around the vehicle is clear of people. The rocking motion may cause the • Avoid flooded roads. Water depth can be decep- vehicle to suddenly lurch forward or backward, tive, and you could be seriously hurt by driving causing injury to by-standers.

  • Page 263: On Snowy Or Icy Roads

    EMERGENCIES 263 CAUTION! CAUTION! • When driving in rain, a layer of water may form Tire chains are not recommended for your vehicle. between the tires and the road surface (hydroplan- The clearance between the chains and the body is ing).

  • Page 264: Spare Tire, Jack And Tool Set Storage

    264 EMERGENCIES SPARE TIRE, JACK AND TOOL SET STORAGE Handling spare tire Loosen Jack Clamp Tool set N01A1180 N03A1870 The spare tire, jack and tool set are stowed in the trunk. Remove the installation clamp to remove the spare tire. To install the spare tire, tighten the clamp firmly with your fingers until the spare tire has no more play.

  • Page 265: Jack

    EMERGENCIES 265 Jack COMPACT SPARE TIRE The compact spare tire is designed to save space in the trunk and its lighter weight makes it easier to use if a flat tire occurs. Storage bracket CAUTION! • The tire pressure should be periodically checked and maintained at the specified pressure while the tire is stowed.

  • Page 266: Wheel Covers (If So Equipped)

    266 EMERGENCIES WHEEL COVERS (IF SO EQUIPPED) CAUTION! To remove • Avoid rapid starting and braking with a compact spare tire. • Avoid driving through automatic vehicle washes and over obstacles that could possibly damage the vehicle’s under-carriage. Because the tire is smaller than the original tire, vehicle ground clearance is slightly reduced.
  • Page 267 EMERGENCIES 267 NOTE: The wheel cover is made of plastic; use caution To install when prying it off. NOTE: Some styles of wheels will have bolt-on type wheel covers. To remove this style, remove the bolts that hold the cover to the wheel. CAUTION! Trying to simply remove the wheel cover with your bare hands may severely injure your fingers.

  • Page 268: Jacking And Tire Changing

    268 EMERGENCIES Before installing the wheel cover to the wheel, make sure that the opening with the symbol mark is correctly aligned with the air valve. JACKING AND TIRE CHANGING If a tire must be changed, do so only after making sure the vehicle is stopped in a safe, flat location.
  • Page 269 EMERGENCIES 269 WARNING! • Do not set the jack at any other position on the vehicle than those specified. If the jack is set at a wrong position, the body of the vehicle could be dented or the jack might fall over and cause personal injury.
  • Page 270 270 EMERGENCIES N22A1450 N21C0280 6. Rotate the jack by hand until the flange portion (D) fits NOTE: Before use, turn the top of jack and set it as in the groove at the top of the jack. shown in the illustration.
  • Page 271 EMERGENCIES 271 N22A1830 N22A0010 7. Remove the wheel nut wrench and bar from the tool 8. Insert the bar (E) into the wheel nut wrench (F). Then bag (located inside the trunk). attach the end of the bar to the jack end, as shown in the illustration.
  • Page 272 272 EMERGENCIES WARNING! • Before using the jack, chock or block the wheel that is tire diagonally opposite the jacking point. • Stop jacking up the vehicle when the tire is raised off the ground. It is dangerous to raise the vehicle any higher.
  • Page 273 EMERGENCIES 273 or in the installation holes in the wheel, and then mount the spare tire. N24A0210 9. Remove the wheel nuts with the wheel nut wrench, then take the wheel off. WARNING! CAUTION! Mount the spare wheel with the valve stem (G) on Handle the wheel cover carefully when replacing the the side facing outward, not on the side facing the flat tire, to avoid the wheel surface becoming...
  • Page 274 274 EMERGENCIES CAUTION! Never apply oil to either wheel bolts or nuts as it can Tapered nut cause them to overtighten. NOTE: Flange nuts can be temporarily used on the steel wheel, but return to the original wheel and tire as soon as possible.
  • Page 275 EMERGENCIES 275 CAUTION! Never use extra force with your foot on the wheel nut wrench or a pipe extension as you can over- tighten the nut. 13. Lower and remove the jack, and store the jack, flat tire and chock. Have the damaged tire repaired as soon as possible.
  • Page 276 276 EMERGENCIES CAUTION! • The emergency tire is to be used only temporarily when the standard tire is damaged. Repair the damaged tire as soon as possible. Replace the emergency tire with the standard tire. • After changing the tire and driving the vehicle approximately 621 miles (1000 km), retighten the wheel nuts to make sure that they are not loose.

  • Page 277: Engine Overheating

    EMERGENCIES 277 ENGINE OVERHEATING CAUTION! If the engine coolant temperature gauge indicator enters the “H” (hot) position, the engine may be overheated. Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull In any of the following situations, you can reduce the over and stop the vehicle.

  • Page 278: Jump-Starting The Engine

    278 EMERGENCIES WARNING! WARNING! • When working near the radiator cooling fan, dis- When using jumper cables to start a vehicle, follow connect the fan motor lead or turn the ignition key procedures exactly and exercise extreme caution. to the OFF position. The fan is temperature con- trolled and can start at any time the ignition key is in the ON position.
  • Page 279 EMERGENCIES 279 connection. You wouldn’t be able to start your vehicle, NOTE: Turn off all lights, heater and other electrical and the bad ground could damage the electrical systems. loads. This will avoid sparks and help save both batter- ies. 4.
  • Page 280 280 EMERGENCIES N29A0790 N29A1070 5. Connect one end of one booster cable to the positive (+) terminal of the discharged battery (A), and the other end to the positive (+) terminal of the booster battery (B). NOTE: Remove the terminal cover before connecting the booster cable to the positive terminal of the battery.
  • Page 281 EMERGENCIES 281 6. Connect one end of the other jumper cable to the WARNING! negative (-) terminal of the booster battery (B), and the • Be sure to observe the connecting sequence of other end to the engine block of the vehicle with the →...

  • Page 282: If Your Vehicle Has Anti-Lock Brakes

    282 EMERGENCIES WARNING! WARNING! • Charging the battery installed in the vehicle • Always wear protective clothing and goggles might cause the battery to catch fire and explode. when working near the battery. Or, damage to the vehicle could result. If it has to •...
  • Page 283 EMERGENCIES 283 CAUTION! Sling lift type • Tie-down hooks should never be used for towing purposes. • This vehicle can NOT be towed by a tow truck using sling lift type equipment. This is to prevent the bumper from deformation. If this vehicle is Flat bed type towed, use wheel lift, dolly type or flat bed equipment.

  • Page 284: Fuses

    284 EMERGENCIES CAUTION! CAUTION! • Towing should only be done by a professional Never tow an automatic transaxle model with the tow service particularly if it will involve towing rear wheels raised (with the front wheels on the on winding roads, hills or heavy traffic. If you ground) when the automatic transaxle fluid level is have any doubts, use a professional tow service.

  • Page 285: Fuse Block

    EMERGENCIES 285 Fuse block FUSIBLE LINKS To prevent damage to the electrical system due to short- Fusible links will melt to prevent a fire in the event that circuiting or overloading, each individual circuit is pro- a large current flows through a system protected by a fusible link.

  • Page 286: Fuse Load Capacities

    286 EMERGENCIES cover of the instrument panel (driver’s side). Always use Fuse load capacities a fuse of the same capacity for replacement. Passenger compartment fuse location Fuse location table No. Symbol Electrical system Capacity Audio — — — Sunroof Accessory socket SOCKET Rear window defogger Heater...
  • Page 287 EMERGENCIES 287 Spare fuse location No. Symbol Electrical system Capacity Spare fuses are contained in the cover of the instru- Engine Control 7.5A ment panel (driver’s side). Always use a fuse of the Windshield wiper same capacity for replacement. Door mirror heater 7.5A Relay 7.5A...
  • Page 288 288 EMERGENCIES Engine compartment Fuse location table Symbol Electrical system Capacity Fuse (+B) Engine compartment fuse location Radiator fan motor Anti-lock braking system Ignition switch Electric window controls Fog lights — — — Horn Engine control Air conditioning Stop lights —...
  • Page 289 EMERGENCIES 289 Fuse replacement Symbol Electrical system Capacity Dome lights Audio Fuel pump Defroster • Some fuses may not be installed on your vehicle. Fuse application depends on the vehicle model, specifica- tions, or options. 7.5A BROWN Blown fuse LIGHT BLUE YELLOW N29C0020 GREEN...
  • Page 290 290 EMERGENCIES N29C0200 N29C0010 4. There is a fuse puller in the cover of the instrument 5. Insert a new fuse of the same capacity securely into the panel (driver’s side). Remove the fuse puller, clamp it on fuse block location. the fuse you wish to remove, and pull the fuse straight out from the fuse block.

  • Page 291: Replacement Of Light Bulbs

    EMERGENCIES 291 CAUTION! • Never use a fuse with a capacity larger than that specified or any substitute, such as wire, foil, etc. Doing so will cause the circuit wiring to heat up and could cause a fire. • If the newly inserted fuse blows again after a short time, have the electrical system checked by an authorized dealer to find and correct the cause.

  • Page 292: Headlights (Type 1)

    292 EMERGENCIES Inside Wattage or Description Candela Power Dome Light Rear personal light Trunk light Reading light Headlights (Type 1) 1. Turn the light socket counterclockwise and pull it out and remove the light bulb. N10B2810 Wattage or ANSI Trade No. Description Candela Power or Bulb type...

  • Page 293: Headlights (Type 2)

    EMERGENCIES 293 2. Pull the clip (A) and remove the light bulb from the Headlights (Type 2) socket. 1. Loosen the bolt (A), move the horn (B) (left side only). N10C1920 N10C1760...
  • Page 294 294 EMERGENCIES 2. Turn the light socket counterclockwise and pull it out 3. Pull the clip (A) and remove the light bulb from the and remove the light bulb. socket. N10C1930 N10C1940...

  • Page 295: Adjustment Of Headlight Aim

    EMERGENCIES 295 Adjustment of headlight aim CAUTION! The alignment of the headlights should be checked by an • Never hold the halogen light bulb with a bare authorized dealer. hand, dirty glove, etc. The oil from your hand Front turn signal and parking lights could cause the bulb to break the next time the headlights are operated.

  • Page 296: Front Side Marker Lights

    296 EMERGENCIES Front side marker lights Front fog lights 1. Turn the front turn signal light socket counterclock- wise. N10D0170 Turn the light socket counterclockwise and pull it out and N10F0760 remove the light bulb.
  • Page 297 EMERGENCIES 297 2. Turn the light socket counterclockwise and pull it out. 3. Pull both clips away from the center as shown and remove the bulb from the socket by pulling out. N10X1650 N10C1700...

  • Page 298: Rear Combination Lights

    298 EMERGENCIES Rear combination lights CAUTION! 1. Turn the trim cover clip (A) counterclockwise and • Never hold the halogen light bulb with a bare remove the trim cover clip. Partially remove the trim cover in the trunk. hand, dirty glove, etc. The oil from your hand could cause the bulb to break the next time the fog lights are operated.
  • Page 299 EMERGENCIES 299 2. Remove the light case mounting nuts. Disconnect the Remove the bulb from the socket by turning it counter- connector. clockwise while pressing it inward. A - Stop and tail light B - Rear turn signal light C - Back up light D - Rear side marker light N20I0100 N20I0160...

  • Page 300: High-Mounted Stop Light

    300 EMERGENCIES High-mounted stop light License plate light N10J0310 N10V0700 Remove the lens mounting screws, remove the socket Remove the socket assembly and bulb together by turn- assembly and the bulb together by turning it counter- ing it counterclockwise. clockwise. And remove the bulb by pulling out. Remove the bulb from the socket by pulling out.

  • Page 301: Dome Light

    EMERGENCIES 301 Trunk light Dome light 1. Insert a flat blade screwdriver into the notch of the light assembly and pry gently downward to remove it. Clips N10O0230 Pull both clips away from the center as shown and N10M0380 remove the light unit. Then remove the bulb by pulling out.
  • Page 302 302 EMERGENCIES 2. Remove the light bulb from the light holder. Reading lights N10M0410 N11I0040 Insert a straight blade screwdriver into the notch of the light assembly and pry gently to remove the lens. Remove the light bulb from the light holder. NOTE: Wrap a cloth around the tip of the straight blade screwdriver in order to avoid scratching the lens.
  • Page 303 EMERGENCIES 303 Rear personal light N10Q0090 Insert the tip of a flat blade screwdriver at the edge of the lens, pry gently to remove the lens, and then remove the bulb from the light holder. NOTE: Wrap a cloth around the tip of the screwdriver in order to avoid scratching the lens.
  • Page 305 MAINTENANCE CONTENTS View of engine compartment ....307 Distributor cap and rotor ....313 Service precautions .
  • Page 306 306 MAINTENANCE Disconnection and connection ... . . 323 Drive belt (for generator, water pump, power steering pump) ......331 Automatic transaxle.

  • Page 307: View Of Engine Compartment

    MAINTENANCE 307 VIEW OF ENGINE COMPARTMENT 7. Brake fluid reservoir 2.4 liter engine 8. Windshield washer reservoir 9. Drive belt 10. Radiator cap 11. Automatic transaxle fluid level dipstick 12. Air cleaner filter 3.0 liter engine Q02A2510 1. Power steering fluid reservoir 2.

  • Page 308: Service Precautions

    308 MAINTENANCE NOTE: The Scheduled Maintenance Charts are located WARNING! in the rear of this maintenance section. Always refer to • When checking or servicing the inside of the the schedules for proper service intervals. engine compartment, be sure the engine is SERVICE PRECAUTIONS stopped and has had a chance to cool down.

  • Page 309: Emission-Control System Maintenance

    MAINTENANCE 309 EMISSION-CONTROL SYSTEM MAINTENANCE WARNING! Your vehicle is equipped with an emission-control sys- • The fan may turn on automatically even if the tem which satisfies all requirements of the U.S. Environ- mental Protection Agency. The emission-control system engine is not running; turn the ignition key to the consists of: “LOCK”...

  • Page 310: Emissions Testing

    310 MAINTENANCE monitors the performance of the emissions, engine, and EMISSIONS TESTING In some localities, it may be or will become a legal automatic transaxle control systems. When these systems requirement to ensure that all emissions components and are operating properly, your vehicle will provide excel- systems are functioning properly as a part of the test lent performance and fuel economy, as well as engine procedure.

  • Page 311: Replacement Parts

    MAINTENANCE 311 If the light is flashing, severe catalytic converter damage WARNING! and power loss will soon occur. Immediate service is required. If you see a fuel leak or if you smell fuel, do not operate the vehicle. Any spark (including from the If the gas cap is not tightened properly, the light may ignition ), flame or smoking material could cause an come on.

  • Page 312: Air Cleaner Filter

    312 MAINTENANCE After replacing the air cleaner filter, reinstall the cover in Air cleaner filter its original position. CAUTION! Take care not to damage the engine air flow sensor when removing the air cleaner cover. Evaporative emission control system (except evaporative emission canister) If the fuel-vapor vent line is clogged or damaged, the fuel-vapor mixture will escape, polluting the atmosphere.

  • Page 313: Spark Plugs

    MAINTENANCE 313 Spark plugs require replacement as frequently as the conventional type spark plug and are designed to last much longer. Iridium tipped NOTE: Use the recommended or equivalent spark plugs type listed under “Engine specifications” on page 375. Use of non-recommended plugs will cause engine dam- age, loss of performance or radio noise.

  • Page 314: General Maintenance

    314 MAINTENANCE GENERAL MAINTENANCE Engine oil and oil filter The following pages contain the maintenance service 2.4 liter engine recommended by DaimlerChrysler. In addition to the general maintenance items for which fixed maintenance Good intervals have been specified, there are other items which are expected to operate satisfactorily without periodic maintenance.
  • Page 315 MAINTENANCE 315 NOTE: The engine must be “OFF” when performing oil 3.0 liter engine level checks. Good If the level does not reach the range of “Good”, which indicates minimum necessary quantity of oil, remove the oil filler cap on the engine valve cover, and refill to within the “Good”...
  • Page 316 316 MAINTENANCE To replace the oil filter Engine oil identification mark The oil filter should be replaced at the time or mileage ILSAC certification mark specified on the scheduled maintenance chart. (“Starburst” symbol) You should be sure that any replacement filter used on this vehicle is a high quality filter.
  • Page 317 MAINTENANCE 317 Recommended engine oil viscosity API service symbol Use engine oil with the proper thickness for the outdoor temperatures where you will be driving. M03A1320 If you are unable to find oils with the ILSAC certification mark (“Starburst” symbol), an API classification SL, SL/CF oil with above label may be used.

  • Page 318: Engine Coolant

    318 MAINTENANCE ENGINE COOLANT CAUTION! To check the coolant level • Do not use alcohol or methanol anti-freeze or any The coolant reserve system provides a quick visual engine coolants mixed with alcohol or methanol method for determining the coolant level. When the anti-freeze.

  • Page 319: Brake Fluid

    MAINTENANCE 319 Radiator cap 5. If the temperature of the engine coolant does not rise The radiator cap must be fully tightened to prevent loss normally after engine warm-up, take the vehicle to an of coolant and engine damage. authorized dealer to have the thermostat checked, and replaced if necessary.

  • Page 320: Clutch Fluid (Manual Transaxle)

    320 MAINTENANCE CLUTCH FLUID (MANUAL TRANSAXLE) To replace the fluid Recommended brake fluid conforming to DOT 3 or DOT 4 should be used. The reservoir cap must be fully tightened to avoid contami- nation from foreign matter or moisture. CAUTION! Good •...

  • Page 321: Battery

    MAINTENANCE 321 BATTERY The condition of the battery is very important for quick starting and to keep the vehicle’s electrical system work- ing properly. Check the battery regularly. If battery performance is suspect, have the battery and charging system tested by an authorized Mitsubishi dealer.
  • Page 322 322 MAINTENANCE Cell B = .31 in (8 mm) M07B0110 Insert the tip of the screwdriver at the edge of the cap, The inside of the battery is divided into several pry gently to remove the cap. compartments. Check the electrolyte level (A) in each cell. The electrolyte level must be within the range (B) shown in the illustration.

  • Page 323: During Cold Weather

    MAINTENANCE 323 Disconnection and connection WARNING! To disconnect the battery cable, stop the engine, discon- • If the battery goes flat, be sure to check the battery nect the negative terminal first, then the positive termi- nal. To reconnect the battery, first connect the positive electrolyte level before connecting booster cables.
  • Page 324 324 MAINTENANCE WARNING! WARNING! • Never disconnect the battery while the engine is • Ventilate the area when charging or using the running; doing so could damage the vehicle’s battery in an enclosed space. electrical components. • Always wear protective clothing and goggles •...

  • Page 325: Automatic Transaxle

    MAINTENANCE 325 NOTE AUTOMATIC TRANSAXLE 1. Check each battery terminal for corrosion. If necessary, neutralize corrosion by washing with a solution of bak- Good ing soda and water. Apply grease to posts and clamps after cleaning or tightening. 2. Before cleaning the battery, tighten all filler port caps to prevent foreign matter from entering the battery.

  • Page 326: To Check The Fluid Level

    326 MAINTENANCE To check the fluid level WARNING! The fluid level should be checked when the engine temperature gauge indicates a normal warmed up con- Transaxle fluid is extremely flammable and poison- dition and the fluid in the transaxle is heated to its ous.

  • Page 327: Manual Transaxle

    MAINTENANCE 327 Special additives rubber hose cover, the hose should be replaced. Deterio- DaimlerChrysler does not recommend the addition of ration of the hose could cause brake failure. any fluid additives to the transaxle. 2. Faulty installation may cause twisting, or wheel, tire or chassis interference.

  • Page 328: Hood Lock Release Mechanism And Safety

    328 MAINTENANCE Whenever a change is noticed in the sound of the exhaust HOOD LOCK RELEASE MECHANISM AND SAFETY CATCH system; when exhaust fumes can be detected inside the The hood lock release mechanism and hood safety catch vehicle; or when the underside or rear of the vehicle is should be inspected, cleaned, and lubricated as required damaged, have a competent technician inspect the com- to maintain ease of operation and to provide protection...

  • Page 329: Windshield Wiper Blades

    MAINTENANCE 329 WINDSHIELD WIPER BLADES Windshield washers Check the wiper blades occasionally. Periodic cleaning of the wiper blades is suggested to remove the accumula- tion of salt and road film. The wiper blade arms and glass areas should be cleaned with a sponge or cloth and a mild detergent or non-abrasive cleaner.

  • Page 330: Parking Brake

    330 MAINTENANCE For vehicles with rear disc brakes: PARKING BRAKE You should feel the parking brake take hold between 3 to 5 clicks. Also check to see if the lever is properly engaged with the ratchet, when pulled. I27A0100 Check the parking brake lever travel occasionally. To check, pull the lever slowly and count the number of clicks of the ratchet.

  • Page 331: Drive Belt (For Generator, Water Pump, Power Steering Pump)

    MAINTENANCE 331 DRIVE BELT (FOR GENERATOR, WATER PUMP, Inspect the drive belt for evidence of cuts and cracks, and POWER STEERING PUMP) replace it if damaged. When replacing the belt with a new belt, make sure that there is no interference between the 2.4 liter engine Power steering belt and other engine components.

  • Page 332: Timing Belt

    332 MAINTENANCE Amount of belt deflection TIRES in (mm) WARNING! Standard value Used belt New belt .27 to .33 .29 to .33 .17 to .21 Driving with tires that are worn or improperly inflated (6.9 to 8.5) (7.4 to 8.5) (4.4 to 5.4) can result in a collision, and serious or fatal injury.
  • Page 333 MAINTENANCE 333 (1) The sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) The outward facing sidewall of an asymmetri- cal tire that has a particular side that must always face outward when mounted on a ve- hicle.
  • Page 334 334 MAINTENANCE letters ‘‘LT’’ that are molded into the sidewall preced- Size Designation EXAMPLE : P215/65R15 ing the size designation. Example LT235/85R16. Passenger car tire size based on U.S.A. de- • Temporary spare tires are high pressure compact sign standards spares designed for temporary emergency use only.
  • Page 335 MAINTENANCE 335 Maximum Load Code representing the tire size. (2 digits) Maximum load indicates the maximum load this tire is ABCD Code used by tire manufacturer. (1 to 4 designed to carry. digits) Number representing the week in which Maximum pressure the tire was manufactured.

  • Page 336: Tire Inflation Pressures

    336 MAINTENANCE wet pavement as measured under controlled conditions 1. Safety on specified government tests surfaces of asphalt and Under-inflation increases tire flexing and can result in tire concrete. A tire marked C may have poor traction perfor- failure. Over-inflation results in a tire losing its ability to mance.

  • Page 337: Radial Ply Tires

    MAINTENANCE 337 door. air out of the tires to match the specified cold pressure, or The recommended inflation pressures should be followed your tires will be underinflated. when the specified tires are installed. Check your tires each time you refuel. If one tire looks lower than the others, check the tire inflation pressure for Item Tire size...

  • Page 338: Tire Pressure For Sustained High-Speed Driving

    338 MAINTENANCE factory-installed tires on this vehicle are of belted con- Tire pressure for sustained high-speed driving struction and are selected to complement the ride and For sustained high-speed driving, increase inflation pres- handling characteristics of your vehicle. sure 4 psi (28 kPa) above the recommended pressure but Radial ply tires have the same load carrying capacity as do not exceed the maximum cold inflation pressure bias or bias-belted tires of the same letter size, and use the...
  • Page 339 MAINTENANCE 339 • Vehicle normal load on the tire : load on an indi- 2. Maintain wheel balance and front suspension align- ment. vidual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, 3.
  • Page 340 340 MAINTENANCE • Vehicle capacity weight : the rated cargo and lug- 2. Determine the combined weight of the driver and gage load plus 150 lbs (68 kg) times the vehicle’s passengers that will be riding in your vehicle. designated seating capacity. 3.
  • Page 341 MAINTENANCE 341 NOTE 1. The following table shows examples on how to calcu- late total cargo/load capacity of your vehicle with a varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load capacity of your vehicle.
  • Page 342 342 MAINTENANCE...

  • Page 343: Cargo Loads

    MAINTENANCE 343 Cargo loads Tread wear indicators The load-carrying capacity of your vehicle is shown on Location of tread wear indicator the tire and loading information placard. DO NOT USE the weight rating data provided on the safety certification label for determining vehicle passen- ger and/or cargo load capacity.

  • Page 344: Tire Rotation

    344 MAINTENANCE When the indicators appear in two or more adjacent Type 2 grooves, tire replacement is recommended. NOTE: The mark and the location of the tire wear indicator are different depending on tire manufacturers. Tire rotation Type 1 M40A0490 However, the timing for tire rotation may vary according to your vehicle condition, road surface conditions and each individual driver’s driving habits.

  • Page 345: Tire Chains

    MAINTENANCE 345 The first rotation is the most important to achieve more Snow tires should be inflated 4 psi (28 kPa) higher than uniform wear for all tires on the vehicle. the inflation pressure shown on the vehicle’s tire placard. Never inflate over the maximum pressure shown on the CAUTION! tire sidewall.

  • Page 346: Regular Maintenance Schedule

    346 MAINTENANCE REGULAR MAINTENANCE SCHEDULE 12,000 Miles (19 000 km) or at 12 months The content and mileage interval can vary depending on Check automatic transaxle fluid level. model. Inspect disc brake pads, rotors and calipers for wear and leaks. 6,000 Miles (10 000 km) or at 6 months Check brake hoses for deterioration or leaks.
  • Page 347 MAINTENANCE 347 24,000 Miles (38 000 km) or at 24 months 30,000 Miles (48 000 km) or at 30 months Check automatic transaxle fluid level. Replace air cleaner filter. Inspect disc brake pads, rotors and calipers for Replace spark plugs, standard type. wear and leaks.
  • Page 348 348 MAINTENANCE 30,000 Miles (48 000 km) or at 30 months 42,000 Miles (67 000 km) or at 42 months Change engine oil and engine oil filter. Change engine oil and engine oil filter. Rotate tires. Rotate tires. MILEAGE/ DEALERSHIP REPAIR MILEAGE/ DEALERSHIP...
  • Page 349 MAINTENANCE 349 54,000 Miles (86 000 km) or at 54 months 60,000 Miles (96 000 km) or at 60 months Change engine oil and engine oil filter. Replace air cleaner filter. Rotate tires. Replace spark plugs, standard type. Replace timing belt.* MILEAGE/ DEALERSHIP REPAIR...
  • Page 350 350 MAINTENANCE 60,000 Miles (96 000 km) or at 60 months 66,000 Miles (106 000 km) or at 66 months Inspect suspension system for looseness and dam- Change engine oil and engine oil filter. age. Rotate tires. Inspect ball joint and steering linkage seals for MILEAGE/ DEALERSHIP REPAIR...
  • Page 351 MAINTENANCE 351 78,000 Miles (125 000 km) or at 78 months 90,000 Miles (144 000 km) or at 90 months Change engine oil and engine oil filter. Replace air cleaner filter. Rotate tires. Replace spark plugs, standard type. Check drive belts condition (for the generator, MILEAGE/ DEALERSHIP REPAIR...
  • Page 352 352 MAINTENANCE 90,000 Miles (144 000 km) or at 90 months 102,000 Miles (163 000 km) or at 102 months Change engine oil and engine oil filter. Replace spark plugs, platinum-tipped type. Rotate tires. Replace timing belt.* : Not required if belt was previously changed. MILEAGE/ DEALERSHIP REPAIR...
  • Page 353 MAINTENANCE 353 114,000 Miles (183 000 km) or at 114 months 120,000 Miles (192 000 km) or at 120 months Change engine oil and engine oil filter. Flush and replace engine coolant. Rotate tires. Inspect rear drum brake linings and rear wheel cylinders (except vehicles with disc brakes) for MILEAGE/ DEALERSHIP...

  • Page 354: Severe Maintenance Schedule

    354 MAINTENANCE SEVERE MAINTENANCE SCHEDULE 120,000 Miles (192 000 km) or at 120 months The content and mileage interval can vary depending on Check fuel system for leak model. (tank, pipe line and connection, and fuel tank filler tube cap). 3,000 Miles (5 000 km) or at 3 months Check evaporative emission control system for leaks and clogging (except evaporative emission...
  • Page 355 MAINTENANCE 355 9,000 Miles (14 000 km) or at 9 months 15,000 Miles (24 000 km) or at 15 months Change engine oil and engine oil filter. Replace air cleaner filter. Rotate tires. Replace spark plugs, standard type. Inspect rear drum brake linings and rear wheel MILEAGE/ DEALERSHIP REPAIR...
  • Page 356 356 MAINTENANCE 18,000 Miles (29 000 km) or at 18 months 24,000 Miles (38 000 km) or at 24 months Change engine oil and engine oil filter. Change engine oil and engine oil filter. Inspect disc brake pads, rotors and calipers for Check automatic transaxle fluid level.
  • Page 357 MAINTENANCE 357 30,000 Miles (48 000 km) or at 30 months 30,000 Miles (48 000 km) or at 30 months Replace air cleaner filter. Change engine oil and engine oil filter. Replace spark plugs, standard type. Inspect disc brake pads, rotors and calipers for Check drive belts condition (for the generator, wear and leaks.
  • Page 358 358 MAINTENANCE 36,000 Miles (58 000 km) or at 36 months 42,000 Miles (67 000 km) or at 42 months Check automatic transaxle fluid level. Change engine oil and engine oil filter. Check brake hoses for deterioration or leaks. Inspect disc brake pads, rotors and calipers for Inspect drive shaft boots for grease leaks and wear and leaks.
  • Page 359 MAINTENANCE 359 48,000 Miles (77 000 km) or at 48 months 54,000 Miles (86 000 km) or at 54 months Change engine oil and engine oil filter. Change engine oil and engine oil filter. Inspect disc brake pads, rotors and calipers for Inspect disc brake pads, rotors and calipers for wear and leaks.
  • Page 360 360 MAINTENANCE 60,000 Miles (96 000 km) 60,000 Miles (96 000 km) or at 48 months Replace air cleaner filter. Inspect ball joint and steering linkage seals for Replace spark plugs, standard type. grease leaks and damage. Check drive belts condition (for the generator, Inspect drive shaft boots for grease leaks and damage.
  • Page 361 MAINTENANCE 361 63,000 Miles (100 000 km) or at 63 months 69,000 Miles (110 000 km) or at 69 months Change engine oil and engine oil filter. Change engine oil and engine oil filter. Rotate tires. Rotate tires. MILEAGE/ DEALERSHIP REPAIR MILEAGE/ DEALERSHIP...
  • Page 362 362 MAINTENANCE 75,000 Miles (120 000 km) or at 75 months 78,000 Miles (125 000 km) or at 78 months Replace air cleaner filter. Change engine oil and engine oil filter. Replace spark plugs, standard type. Inspect disc brake pads, rotors and calipers for Inspect rear drum brake linings and rear wheel wear and leaks.
  • Page 363 MAINTENANCE 363 84,000 Miles (134 000 km) or at 84 months 90,000 Miles (144 000 km) or at 90 months Change engine oil and engine oil filter. Replace air cleaner filter. Inspect disc brake pads, rotors and calipers for Replace spark plugs, standard type. wear and leaks.
  • Page 364 364 MAINTENANCE 90,000 Miles (144 000 km) or at 90 months 96,000 Miles (154 000 km) or at 96 months Inspect suspension system for looseness and dam- Change engine oil and engine oil filter. age. Inspect disc brake pads, rotors and calipers for Change engine oil and engine oil filter.
  • Page 365 MAINTENANCE 365 102,000 Miles (163 000 km) or at 102 months 105,000 Miles (168 000 km) or at 105 months Replace spark plugs, platinum-tipped type. Change engine oil and engine oil filter. Change engine oil and engine oil filter. Rotate tires. Inspect disc brake pads, rotors and calipers for MILEAGE/ DEALERSHIP...
  • Page 366 366 MAINTENANCE 111,000 Miles (178 000 km) or at 111 months 117,000 Miles (187 000 km) or at 117 months Change engine oil and engine oil filter. Change engine oil and engine oil filter. Rotate tires. Rotate tires. MILEAGE/ DEALERSHIP REPAIR MILEAGE/ DEALERSHIP...
  • Page 367 MAINTENANCE 367 120,000 Miles (192 000 km) or at 120 months 120,000 Miles (192 000 km) or at 120 months Change manual transaxle fluid. Check evaporative emission control system (ex- Change automatic transaxle fluid. cept evaporative emission canister). Check fuel hoses condition. Check distributor cap and rotor.
  • Page 368 368 MAINTENANCE...
  • Page 369 SPECIFICATIONS CONTENTS Vehicle labeling ......370 7 - Certification label ....372 1 - Vehicle emission control information label .

  • Page 370: 370 Specifications

    370 SPECIFICATIONS VEHICLE LABELING 2 -Vehicle identification number plate This is stamped on the number plate riveted to the left front corner of the instrument panel pad. It is visible from outside of the vehicle through the windshield. 3 - Vehicle information code plate The vehicle information code plate is located on the bulkhead inside the engine compartment.

  • Page 371: Engine Serial Number

    SPECIFICATIONS 371 5 - Engine serial number 4 Cylinder 6 Cylinder B02B0540 B02B0550 The engine serial number is stamped on the cylinder block as shown in the illustrations.

  • Page 372: Tire And Loading Information Placard

    372 SPECIFICATIONS 6 - Tire and loading information placard The tire inflation pressure label is located on the inside sill of the driver’s door. B02F0060 BATTERY B02E0180 BCI Group NO.86 7 - Certification label Battery is 12 volts. The certification label is located on the inside sill of the NOTE: There are various size of the batteries in the BCI driver’s door.

  • Page 373: General Vehicle Data

    SPECIFICATIONS 373 GENERAL VEHICLE DATA NOTE: These tires satisfy vehicle loading conditions described in the owner’s manual. Overall length 191.9in (4,875mm) VEHICLE WEIGHTS Overall width 69.9in (1,775mm) Item 2.4 liter 3.0 liter Overall height 53.9in (1,370mm) Gross vehicle Wheel base 103.7in (2,635mm) 4,061lb (1,842 kg) 4,227lb (1,917 kg) weight rating...
  • Page 374 374 SPECIFICATIONS CAUTION! Do not use the gross vehicle weight rating data provided in the chart or on the safety certification label for determining vehicle passenger and/or cargo load capacity. Use the values provided on the tire and loading information placard (Refer to the section “Vehicle labeling”).

  • Page 375: Engine Specifications

    SPECIFICATIONS 375 ENGINE SPECIFICATIONS Item Specifications Engine model 4 Cylinder 6 Cylinder Engine displacement 2,351dm (143.4 CID) 2,972dm (181.3 CID) No. of cylinders and cylinder arrangement 4 in-line 6 - V60 ° Bore 86.5 mm (3.41 in) 91.1 mm (3.58 in) Stroke 100 mm (3.94 in) 76.0 mm (2.99 in)

  • Page 376: Capacities

    376 SPECIFICATIONS CAPACITIES Item Capacity Recommended Lubricants Fuel (approximate) 62dm (16.3 gal) — Engine oil Oil pan (4.2 qt) Engine oils displaying ILSAC certification symbol or conforming to the API Oil filter 0.3dm (0.32 qt) classification SL, SL/CF Power steering 1.2dm (1.3 qt) Diamond ATF...

  • Page 377: If You Need Consumer Assistance

    IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service Reporting Safety Defects ....381 For Your Vehicle ..... . . 378 In Canada .

  • Page 378: Suggestions For Obtaining Service For Your Vehicle

    378 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE..YOUR VEHICLE DaimlerChrysler Motors Corporation and its dealers are vitally interested in your satisfaction. We want you to be Prepare For The Appointment happy with our products and services. If you’re having warranty work done, be sure to have the right papers with you.
  • Page 379 • If for some reason you are still not satisfied, talk to the DaimlerChrysler Canada Inc. Customer Service general manager or owner of the dealership. They Chrysler Center want to know if you need assistance. P.O. Box 1621 Windsor, Ontario N9A 4H6 •...

  • Page 380: Warranty Information

    380 IF YOU NEED CONSUMER ASSISTANCE DaimlerChrysler Motors Corporation will not stand be- Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) hind any service contract that is not a Genuine To assist customers who have hearing difficulties, DaimlerChrysler Motors Corporation Service Contract. It DaimlerChrysler Motors Corporation has installed spe- is not responsible for any service contract other than a cial TDD (Telecommunication Devices for the Deaf)

  • Page 381: Mopar Parts

    IF YOU NEED CONSUMER ASSISTANCE 381 MOPAR PARTS If NHTSA receives similar complaints, it may open an Mopar fluids, lubricants, parts, and accessories are avail- investigation, and if it finds that a safety defect exists in able from your DaimlerChrysler Motors Corporation a group of vehicles, it may order a recall and remedy dealer.

  • Page 383: Publication Order Forms

    PUBLICATION ORDER FORMS...

  • Page 385: Department Of Transportation Uniform Tire Quality Grades

    IF YOU NEED CONSUMER ASSISTANCE 385 DEPARTMENT OF TRANSPORTATION UNIFORM Traction AA, A, B, C TIRE QUALITY GRADES The traction grades, from highest to lowest, are AA, A, B The following describes the tire grading categories estab- and C. Those grades represent the tire’s ability to stop on lished by the National highway Traffic Safety Adminis- wet pavement as measured under controlled conditions tration.

  • Page 386: Temperature A, B, C

    386 IF YOU NEED CONSUMER ASSISTANCE Temperature A, B, C WARNING! The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat when tested under a tire that is properly inflated and not overloaded.

  • Page 387: Index

    INDEX...
  • Page 388 388 INDEX Accessory boxes ......213 Ball joint, steering linkage seal and drive Accessory (installation) ....248 shaft boots .
  • Page 389 INDEX 389 Cassette Tape and Player Maintenance ..224 Dealer Service ......378 Cassette Tape Player .
  • Page 390 390 INDEX Engine coolant ......318 Fuel selection ......144 Engine coolant level warning light .
  • Page 391 INDEX 391 Dimmer ......122 Keyless entry system ..... 29 Headlight flasher (high/low beam) .
  • Page 392 392 INDEX Odometer ......106,110 Radial ply tires ......337 Oil pressure gauge .
  • Page 393 INDEX 393 Seats Warning light ..... 107,116 Front seats ......57 Supplemental Restraint System (SRS) - Air bag .
  • Page 394 394 INDEX Tire chains ......345 Vanity mirror ......209 Tread wear indicators .

Table of Contents