Genie GS-3384 Service Manual page 187

September 2005
REV A
Code Problem
Megajector internal
363
actuator fault detection
Megajector internal
364
circuitry fault detection
MegaJector internal
365
communication fault
detection
411
Coil Driver #1 Open
412
Coil Driver #1 Shorted
413
Coil Driver #2 Open
414
Coil Driver #2 Shorted
511
FPP1 High Voltage
512
FPP1 Low Voltage
FPP1 Higher than IVS
513
Limit
FPP1 Lower than IVS
514
Limit
521
FPP2 High Voltage
522
FPP2 Low Voltage
TPS1 (Signal Voltage)
531
High
TPS1 (Signal Voltage)
532
Low
TPS2 (Signal Voltage)
533
High
TPS2 (Signal Voltage)
534
Low
Part No. 82259
Cause
The MegaJector detects an internal fault.
Open or short in power, ground or CAN
circuits.s
The MegaJector detects an internal circuitry
failure. Open or short in power, ground or
CAN circuits.
The MegaJector detects an internal
communications failure. Open or short in
power, ground or CAN circuits.
Open wiring and/or connections to ignition
coil #1 OR ignition coil #1 is faulty.
Wiring and/or connections to ignition coil #1
shorted OR ignition coil #1 is faulty.
Open wiring and/or connections to ignition
coil #2 OR ignition coil #2 is faulty.
Wiring and/or connections to ignition coil #2
shorted OR ignition coil #2 is faulty.
Not used.
Not used.
Not used.
Not used.
Not used.
Not used.
The #1 throttle position sensor wiring and/or
connections open or shorted OR there is a
poor system ground connection OR throttle
position sensor #1 is faulty.
The #1 throttle position sensor wiring and/or
connections open or shorted OR there is a
poor system ground connection OR throttle
position sensor #1 is faulty.
The #2 throttle position sensor wiring and/or
connections open or shorted OR there is a
poor system ground connection OR throttle
position sensor #2 is faulty.
The #2 throttle position sensor wiring and/or
connections open or shorted OR there is a
poor system ground connection OR throttle
position sensor #2 is faulty.
GS-3384
Section 5 • Fault Codes
FORD ENGINE ECM FAULT CODE CHART
(AFTER SERIAL NUMBER GS8404-40301)
Check Power, Ground and CAN circuits
at MegaJector and all connections and
repair as necessary OR MegaJector has
an internal fault. Contact Ford Power
Products for assistance.
Check Power, Ground and CAN circuits
at MegaJector and all connections and
repair as necessary OR MegaJector has
an internal fault. Contact Ford Power
Products for assistance.
Check Power, Ground and CAN circuits
at MegaJector and all connections and
repair as necessary OR MegaJector has
an internal fault. Contact Ford Power
Products for assistance.
Repair wiring and/or connections to
ignition coil #1 OR replace ignition coil
#1.
Repair wiring and/or connections to
ignition coil #1 OR replace ignition coil
#1.
Repair wiring and/or connections to
ignition coil #1 OR replace ignition coil
#1.
Repair wiring and/or connections to
ignition coil #2 OR replace ignition coil
#2.
If this fault appears on your machine,
contact Genie Industries Service
Department.
If this fault appears on your machine,
contact Genie Industries Service
Department.
If this fault appears on your machine,
contact Genie Industries Service
Department.
If this fault appears on your machine,
contact Genie Industries Service
Department.
If this fault appears on your machine,
contact Genie Industries Service
Department.
If this fault appears on your machine,
contact Genie Industries Service
Department.
Be sure system ground connections are
in place and secure OR repair wiring
and/or connections to sensor OR replace
throttle position sensor #1.
Be sure system ground connections are
in place and secure OR repair wiring
and/or connections to sensor OR replace
throttle position sensor #1.
Be sure system ground connections are
in place and secure OR repair wiring
and/or connections to sensor OR replace
throttle position sensor #2.
Be sure system ground connections are
in place and secure OR repair wiring
and/or connections to sensor OR replace
throttle position sensor #2.
Continued on next page
Solution
5 - 13