Genie GS-3384 Service Manual page 185

September 2005
REV A
Code Problem
161
System Voltage Low
162
System Voltage High
211
IAT High Voltage
212
IAT Low Voltage
IAT Higher Than
213
Expected (1)
IAT Higher Than
214
Expected (2)
215
Oil Pressure Low
221
CHT/ECT High Voltage
222
CHT/ECT Low Voltage
CHT Higher Than
223
Expected (1)
CHT Higher Than
224
Expected (2)
231
MAP High Pressure
232
MAP Low Voltage
234
BP High Pressure
235
BP Low Pressure
242
Crank Sync Noise
Never Crank Synced At
243
Start
244
Camshaft Sensor Loss
Part No. 82259
Cause
Battery is faulty OR alternator is not charging
OR battery supply wiring to ECM is open or
shorted.
Alternator is overcharging the battery when
engine RPM is greater than 1500 rpm.
IAT sensor wiring and/or connections are
open or shorted OR sensor is faulty OR
engine intake air temperature is too cold.
IAT sensor wiring and/or connections are
open or shorted OR sensor is faulty OR
engine intake air temperature is too hot.
Air intake temperature is greater than 200° F
with the engine greater than 1000 rpm OR air
intake system has leaks OR IAT sensor is
faulty.
Air intake temperature is greater than 210° F
with the engine greater than 1000 rpm OR air
intake system has leaks OR IAT sensor is
faulty.
Faulty oil pressure sensor OR sensor wiring
and/or connections open or shorted OR
engine oil level too low.
Engine cooling system is malfunctioning OR
sensor wires and/or connections open or
shorted OR sensor is faulty.
Engine cooling system is malfunctioning and
overheating the engine OR sensor wires
and/or connections open or shorted OR
sensor is faulty OR coolant level is low.
Coolant temperature at the cylinder head is
240° F. Engine cooling system is
malfunctioning and overheating the engine
OR sensor wires and/or connections open or
shorted OR sensor is faulty OR coolant level
is low.
Coolant temperature at the cylinder head is
250° F. Engine cooling system is
malfunctioning and overheating the engine
OR sensor wires and/or connections open or
shorted OR sensor is faulty OR coolant level
is low.
Open or shorted wiring and/or connections to
MAP sensor OR sensor is faulty.
Open or shorted wiring and/or connections to
MAP sensor OR sensor is faulty.
MAP sensor is faulty OR ECM is faulty.
MAP sensor is faulty OR ECM is faulty.
Crankshaft position sensor wiring and/or
connections open or shorted OR there is a
poor system ground connection OR sensor is
faulty.
Crankshaft position sensor wiring and/or
connections open or shorted OR there is a
poor system ground connection OR sensor is
faulty.
Camshaft position sensor wiring and/or
connections open or shorted OR there is a
poor system ground connection OR sensor is
faulty.
GS-3384
Section 5 • Fault Codes
FORD ENGINE ECM FAULT CODE CHART
(AFTER SERIAL NUMBER GS8404-40301)
Replace battery OR repair alternator OR
repair battery supply wiring to ECM.
Repair or replace the alternator.
Repair wiring and/or connections OR
replace sensor OR direct warmer air into
air intake.
Repair wiring and/or connections OR
replace sensor OR direct cooler air into
air intake.
Check air intake system for damage and
proper routing of air intake components
OR replace the IAT sensor.
Check air intake system for damage and
proper routing of air intake components
OR replace the IAT sensor.
Replace oil pressure sensor OR repair
sensor wiring and/or connections OR fill
engine oil level to specification.
Repair engine cooling system problems
OR repair open or shorted wiring to
sensor OR replace sensor.
Repair engine cooling system problems
OR repair open or shorted wiring to
sensor OR replace sensor OR fill engine
coolant level to specification.
Repair engine cooling system problems
OR repair open or shorted wiring to
sensor OR replace sensor OR fill engine
coolant level to specification.
Repair engine cooling system problems
OR repair open or shorted wiring to
sensor OR replace sensor OR fill engine
coolant level to specification.
Repair wiring and/or connections to
sensor OR replace MAP sensor.
Repair wiring and/or connections to
sensor OR replace MAP sensor.
Replace MAP sensor OR replace the
ECM.
Replace MAP sensor OR replace the
ECM.
Be sure system ground connections are
in place and secure OR repair wiring
and/or connections to sensor OR replace
sensor.
Be sure system ground connections are
in place and secure OR repair wiring
and/or connections to sensor OR replace
sensor.
Be sure system ground connections are
in place and secure OR repair wiring
and/or connections to sensor OR replace
sensor.
Continued on next page
Solution
5 - 11