Check Procedure; Setting Method - Epson WorkForce 600 Service Manual

EPSON WorkForce 600/EPSON Stylus OFFICE TX600FW/BX600FW/EPSON Stylus SX600FW/ME OFFICE 700FW
5. Enter fax mode by pushing fax button.
6. Input fax number of PC on "R" unit. (Regarding FAX number, refer to the
telephone line simulator's manual.)
7. Push "Start" button in "B&W" mode.
8. Push "Back" button after being displayed as "Send another page?" on LCD
panel to send fax data from "R" unit to PC.
CHECK POINT OF "R" UNIT
Checked
Check Timing
Function
After sending of fax data
Fax Function
After receiving of fax data
During calling of fax
(Step 9)
External
Connection (EXT
port) Function
During receiving fax data
(Step 10)
3.6.2.2 Fax Function Check by [Method B] and External
Connection Function Check

SETTING METHOD

Guaranteed
Unit
Telephone line
Fax cable
simulator
*Guaranteed unit means
*Regarding FAX number,
FAX function and EXT
refer to the telephone line
port perform correctly.
simulator's manual.
Guaranteed EPSON
WorkForce 600/EPSON
Stylus OFFICE
TX600FW/BX600FW/
EPSON Stylus SX600FW/
ME OFFICE 700FW is
represented by "G" unit
from this.
TROUBLESHOOTING
Check Point
Make sure that "R" unit sends fax data
correctly.
Make sure that "R" unit receives fax data
correctly.
Check if you can hear ringing tone from
telephone before receiving fax. In this case,
the telephone sounds ringing.
Check if you can't hear dial tone from the
telephone during receiving fax data. In this
case, the telephone doesn't sound dial tone.
Telephone
Fax cable
Repaired/refurbished
EXT port
EPSON WorkForce 600/
EPSON Stylus OFFICE
TX600FW/BX600FW/
Fax cable
Line port
EPSON Stylus
SX600FW/ME OFFICE
700FW
*Repaired/refurbished EPSON
WorkForce 600/EPSON Stylus
OFFICE TX600FW/BX600FW/
EPSON Stylus SX600FW/ME
OFFICE 700FW is represented by
"R" unit from this.
*Refer to Table 3-35 on page 83
default setting.
Fax Function/External Connection (EXT port) Function Check

CHECK PROCEDURE

[Sender: "R" unit => Receiver: "G" unit]
1. Set test chart on the document glass of "R" unit.
2. Enter fax mode by pushing fax button.
3. Input fax number of "G" unit on "R" unit. (Regarding FAX number, refer to
the telephone line simulator's manual.)
4. Push "Start" button in "B&W" mode.
5. Push "Back" button after being displayed as "Send another page?" on LCD
panel to send fax data from "R" unit to "G" unit.
[Sender: "G" unit => Receiver: "R" unit]
1. Set test chart on the document glass of "G" unit.
2. Enter fax mode by pushing fax button.
3. Input fax number of "R" unit on "G" unit. (Regarding FAX number, refer to
the telephone line simulator's manual.)
4. Push "Start" button in "B&W" mode.
5. Push "Back" button after being displayed as "Send another page?" on LCD
panel to send fax data from "G" unit to "R" unit.
6. Confirm if telephone rings correctly during calling tone of "R" unit rings.
7. Confirm if dial tone of telephone is lost during "R" unit receives fax data
without calling tone.
CHECK POINT OF "R" UNIT
Checked
Function
After sending of fax data
Fax Function
After receiving of fax data
During calling of fax
(Step 6)
External
Connection (EXT
port) Function
During receiving fax data
(Step 7)
for
Check Timing Check Point
Make sure that "R" unit sends fax data
correctly.
Make sure that "R" unit receives fax data
correctly.
Check if you can hear ringing tone from
telephone before receiving fax. In this case,
the telephone sounds ringing.
Check if you can't hear dial tone from the
telephone during receiving fax data. In this
case, the telephone doesn't sound dial tone.
Revision A
87
Confidential