Stationary Window - 2-Door Cherokee; Stationery Window 4-Door Cherokee - Wagoneer - Jeep 1979 CJ-5 Technical & Service Manual

3K-2
REAR QUARTER
font Window Glass
Removal
(1) Remove handle-to-frame attaching screws
(fig.3K-l).
(2) Remove glass hinge screws and washers.
(3) Remove glass.
NOTE: If glass sticks to hinges, remove glass by care-
fully pushing out hinge screw inserts.
(4) To remove handle assembly from glass, care-
fully drive out handle assembly-to-stud roll pin.
(5) Unscrew stud nut and remove stud from glass.
Installation
(1) Attach glass to frame using hinge screw inserts,
washers, and screws.
(2) Attach handle assembly to frame.
(3) Attach stud and nut to glass, and connect stud
to handle assembly with roll pin.
(4) Latch window and check for water leaks.
(5) If water leakage is evident, apply sealant in af-
fected areas.
STATIONARY WINDOW-2-DOOR CHEROKEE
NOTE: On Cherokee models, the pivoting rear quarter
vent window and frame may remain in the vehicle but
removal of the mylar filler strip is required to accom-
plish removal of the stationary window.
(1) Free weatherstrip-to-body flange (on inside of
vehicles) as follows: starting at top corner, using fingers
or a wooden wand, pull weatherstrip down to clear
flange while exerting an outward pressure on glass.
(2) Push window and weatherstrip toward outside
of vehicle.
(3) Remove weatherstrip from glass and clean off
sealer from glass cavity.
(4) Before installing glass in weatherstrip, apply a
3/16-inch bead of 3M Windshield Sealer or equivalent in
w e a t h e r s t r i p glass cavity using a pressure type
applicator.
(5) Lubricate weatherstrip with soapy water.
(6) Place glass and weatherstrip into position in
window opening.
(7) With weatherstrip body flange in proper posi-
tion at bottom of window opening, use a wooden wand
and walk weatherstrip-to-body flange into position.
(8) Clean excess sealer from glass.
(9) Check for water leaks.
(10) If water leakage is evident between weath-
erstrip and flange, apply 3M Auto Bedding and Glazing
Compound or equivalent to affected areas and realign
weatherstrip.
STATIONARY
WINDOW—CJ-7
WITH HARDTOP
ENCLOSURE
R e i o t a l
(1) Unlock rubber weatherstrip using wood wand or
fiber stick.
(2) Use fiber stick to break seal between glass and
rubber weatherstrip.
(3) Push glass and weatherstrip toward outside of
vehicle. Remove glass.
(4) Remove weatherstrip from opening.
Installation
(1) Inspect weatherstrip and clean sealer from glass
cavity and flange cavity.
N O T E : Inspect for uneven surfaces or irregularities in
the opening flange that could cause stress damage to the
glass.
(2) Before installing weatherstrip on flange, apply a
3/16-inch bead of 3M Auto Bedding and Glazing Com-
pound or equivalent in weatherstrip flange cavity using
a pressure-type applicator.
(3) Install weatherstrip on liftgate opening flange.
(4) Apply a liberal amount of liquid soap solution to
glass cavity of weatherstrip.
(5) Position glass into upper glass cavity and into
each side. Position wooden wand under glass and lift up
and into lower cavity. Check for equal side clearance.
(6) Use wooden wand to lock weatherstrip.
NOTE: Soap solution should be removed from the
weatherstrip and glass before installing sealer.
(7) Using a pressure-type applicator, apply 3M
Windshield Sealer or equivalent between weatherstrip
and glass on outside of glass around entire perimeter.
STATIONARY W 1 N D 0 W - 4 - D 0 0 R CHER0KEE-WA60NEER
Removal
(1) Remove interior garnish mouldings from
around window and break seal loose between weath-
erstrip and body panels.
(2) Push glass toward inside of vehicle.
(3) Remove weatherstrip from around glass and
clean old sealer from glass cavity and flange cavity.
Installation
(1) Before installing glass in weatherstrip, apply a
3/16-inch bead of 3M Windshield Sealer or equivalent in
glass cavity completely around weatherstrip using a
pressure type applicator (fig. 3K-2).