Page 1
Liberty 2 0 1 2 O W N E R ’ S M A N U A L...
Page 2
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of fea- Chrysler Group LLC shall be deemed to be deleted and the tures and equipment that are either standard or optional on name Chrysler Canada Inc.
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
INTRODUCTION 5 two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire.
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has You can insert the double-sided keys into the locks with the key code numbers for your vehicle locks. These either side up.
Page 15
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: • For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), features such as the power window switches, radio, power sunroof or Sky Slider (if equipped), and power outlets will remain active for 45 seconds after the ignition switch is turned to the LOCK position.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! CAUTION! • When leaving the vehicle, always remove the key An unlocked vehicle is an invitation to thieves. fob from the ignition and lock your vehicle. Always remove the key from the ignition, and lock •...
Page 17
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 is automatic, regardless of whether the vehicle is locked someone used an invalid key to try to start the engine. or unlocked. Either of these conditions will result in the engine being shut off after two seconds.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one NOTE: Only keys that are programmed to the vehicle that has never been programmed. electronics can be used to start and operate the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 3. Insert the second valid key into the ignition switch. Repeat this procedure to program up to eight keys. If you Turn the ignition switch to the ON/RUN position within do not have a programmed Sentry Key , contact your 15 seconds.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED one should go off in the future, you will need to know The Vehicle Security Alarm monitors the vehicle doors, which mode has been activated in order to deactivate it. liftgate, and liftgate flipper glass for unauthorized entry Rearming Of The System and ignition for unauthorized operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 • When the Vehicle Security Alarm is armed, the interior 3. Close all doors. The Vehicle Security Light in the instrument cluster will flash rapidly for about 16 seconds power door lock switches will not unlock the doors. to signal that the Vehicle Security Alarm is arming.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Illuminated Entry system will not operate if the ILLUMINATED ENTRY The courtesy lights will turn on when you use the dimmer control is in the “Dome defeat” position Remote Keyless Entry (RKE) transmitter to unlock the (extreme bottom position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Remote Key Unlock, Driver Door/All Doors First This feature lets you program the system to unlock either the driver’s door or all doors and the liftgate on the first press of the UNLOCK button on the RKE transmitter. To change the current setting, proceed as follows: •...
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the feature from outside the vehicle by pressing To Lock The Doors And Liftgate the LOCK and UNLOCK buttons on the RKE transmitter. Press and release the LOCK button on the RKE transmit- ter to lock all doors and the liftgate.
Page 25
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, perform the Flash Lights With Lock following steps: The feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmit- 1.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the feature from outside the vehicle by pressing Using The Panic Alarm the LOCK and UNLOCK buttons on the RKE transmitter. NOTE: The PANIC and Security Alarms are quite 4. Repeat these steps if you want to return this feature to different.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 During the PANIC Mode, the door locks and Remote Battery Replacement Keyless Entry (RKE) system will function normally. The recommended replacement battery is CR2032. PANIC mode will not disarm the Security System on NOTE: vehicles so equipped.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. With the RKE transmitter buttons facing down, use a 3. Remove and replace the battery. Avoid touching the flat blade tool to pry the two halves of the RKE transmit- new battery with your fingers. Skin oils may cause ter case apart.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: Changes or modifications not expressly ap- NOTE: • The vehicle must be equipped with an automatic proved by the party responsible for compliance could void the user’s authority to operate the equipment. transmission to be equipped with Remote Start.
Page 30
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Battery at an acceptable charge level. Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped • RKE PANIC button not pressed. The following messages will display in the EVIC if the •...
Page 31
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • The engine can be started two consecutive times (two To Enter Remote Start Mode Press and release the REMOTE START button 15-minute cycles) with the RKE transmitter. However, on the RKE transmitter twice within five sec- the ignition switch must be cycled to the ON/RUN onds.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Power Door Locks WARNING! A power door lock switch is located on each of the front • For personal security and safety in the event of an door trim panels. Use this switch to lock or unlock the doors and liftgate.
Page 34
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you press the power door LOCK switch while the key 2. The transmission is in gear and the vehicle speed is in the ignition, and any front door is open, the power returned to 0 mph (0 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 • For vehicles not equipped with the EVIC, perform the Repeat these steps if you want to return this feature to its following procedure: previous setting. 1. Close all doors and place the key in the ignition. NOTE: Use the Automatic Unlock Doors On Exit feature in accordance with local laws.
Page 36
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To use the system, open each rear door, use a flat blade NOTE: • When the child lock system is engaged, the door can screwdriver (or ignition key) and rotate the dial counter- clockwise to engage the Child-Protection lock and clock- be opened only by using the outside door handle even wise to disengage the Child-Protection locks.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged. WINDOWS Power Windows The window controls on the driver’s door trim panel control all the door windows.
Page 38
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To stop the window from going all the way down during WARNING! the Auto-Down operation, pull up on the switch briefly. Never leave children in a vehicle, with the key in the For vehicles not equipped with the Electronic Vehicle ignition switch.
Page 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Auto Up Feature With Anti-Pinch Protection — If For vehicles equipped with the EVIC, the power window Equipped switches will remain active for up to 10 minutes after the On some models, the driver’s and front passenger’s (if ignition switch is turned to the LOCK position.
Page 40
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Push the window switch down firmly to the second WARNING! detent to open the window completely and continue to hold the switch down for an additional two seconds after There is no anti-pinch protection when the window the window is fully open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof or Sky Slider™ (if equipped) in certain open or partially open positions.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE NOTE: Use the power door LOCK switch on either front To open the liftgate, pull up (squeeze) on the handle and door trim panel or the Remote Keyless Entry (RKE) lift. transmitter to lock and unlock the liftgate.
Page 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! To avoid injury, stand back when opening. Glass may automatically rise. NOTE: If a malfunction to the liftgate latch should occur, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front seat belts incorporate pretensioners that may OCCUPANT RESTRAINTS Some of the most important safety features in your enhance occupant protection by managing occupant vehicle are the restraint systems: energy during an impact event •...
Page 45
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: The Advanced Front Air Bags have a multistage secured in the rear seat in child restraints or belt- inflator design. This allows the air bag to have different positioning booster seats. Older children who do not use rates of inflation based on the severity and type of child restraints or belt-positioning booster seats should collision.
Page 46
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Do not lean against the door or window. If your WARNING! (Continued) vehicle has side air bags, and deployment occurs, the • Being too close to the steering wheel or instrument side air bags will inflate forcefully into the space panel during Advanced Front Air Bag deployment between you and the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Buckle up even though you are an excellent driver, even collision, the belt will lock and reduce your risk of on short trips. Someone on the road may be a poor driver striking the inside of the vehicle or being thrown out.
Page 48
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat belt latch plates are located on the C-Pillar for the WARNING! (Continued) outboard rear seating positions and next to your arm in • Wearing your belt in the wrong place could make the center rear seating position.
Page 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt that is buckled into the wrong buckle will not protect you properly.
Page 50
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tight, tilt the latch plate and pull on the lap belt. A snug WARNING! (Continued) belt reduces the risk of sliding under the belt in a • A belt that is worn under your arm is dangerous. collision.
Page 51
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the shoulder belt anchorage to be adjusted in the upward As a guide, if you are shorter than average, you will position without pressing the release button. To verify prefer a lower position, and if you are taller than average, the shoulder belt anchorage is latched, pull downward you will prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 • ALR — Automatic Locking Retractor Seat Belt Lock Out The center rear seat belt system has a lock out feature that If the passenger seating position is equipped with an will not allow you to extract the center webbing unless ALR and is being used for normal usage: the rear seat upper latch is engaged.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE anytime a child safety seat is installed in a seating WARNING! position that has a belt with this feature. Children • The belt and retractor assembly must be replaced 12 years old and under should always be properly restrained in the rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 tight around the occupant early in a collision. Pretension- WARNING! ers work for all size occupants, including those in child • The belt and retractor assembly must be replaced restraints. if the seat belt assembly “Automatic Locking Re- NOTE: These devices are not a substitute for proper seat tractor (ALR)”...
Page 56
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Active Head Restraints (AHR) Work The Occupant Restraint Controller (ORC) determines whether the severity, or type of rear impact will require the Active Head Restraints (AHR) to deploy. If a rear impact requires deployment, both the driver and front passenger seat AHRs will be deployed.
Page 57
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 1. Grasp the deployed AHR from the rear seat. CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 58
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 3 — Final Downward Movement To Engage Locking Mechanism 4. The AHR front soft foam and trim half should lock 1 —...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Enhanced Seat Belt Use Reminder System (BeltAlert ) BeltAlert is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert ) to fasten their seat belts. The feature is active whenever the ignition is on.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE unbuckled while traveling at speeds greater than 5 mph Seat Belts And Pregnant Women (8 km/h), BeltAlert will provide both audio and visual We recommend that pregnant women use the seat belts notification.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
Page 62
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Air Bags based upon seat position. This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether the driver or front passenger seat belt is fastened.
Page 63
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • Supplemental Active Head Restraint for Driver and Air Bag System Components Your vehicle may be equipped with the following air bag Front Passenger system components: • Occupant Classification System (OCS) • Occupant Restraint Controller (ORC) •...
Page 64
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The passenger Advanced Front Air Bag may not WARNING! (Continued) deploy, even when the driver Advanced Front Air Bag • Do not put anything on or around the air bag has, if the Occupant Classification System (refer to Oc- covers or attempt to manually open them.
Page 65
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 NOTE: WARNING! (Continued) • Should a vehicle rollover occur, the pretensioners • Do not have any accessory items installed which and/or SABIC air bags on both sides of the vehicle will alter the roof, including adding a sunroof to may deploy.
Page 66
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • If your vehicle is equipped with SABIC air bags, • If your vehicle is equipped with left and right do not have any accessory items installed which Supplemental Side Air Bag Inflatable Curtain will alter the roof, including adding a sunroof to (SABIC), do not stack luggage or other cargo up your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Along with seat belts and pretensioners, Advanced Front Advanced Front Air Bags are designed to provide addi- Air Bags work with the knee bolsters to provide im- tional protection by supplementing the seat belts in proved protection for the driver and front passenger.
Page 68
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Because air bag sensors measure vehicle deceleration Also, the ORC turns on the “Air Bag Warning over time, vehicle speed and damage by themselves are Light” for four to eight seconds for a self-check not good indicators of whether or not an air bag should when the ignition is first turned to ON/RUN.
Page 69
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • Occupant Classification Module (OCM) WARNING! The OCM is located beneath the front passenger seat. The OCM classifies the occupant into categories based on the Ignoring the Air Bag Warning Light in your instru- measurements made by the seat weight sensors.
Page 70
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “PASS AIR BAG OFF” to show that the passenger The PAD indicator light should not be illuminated when Advanced Front Air Bag will not inflate during a collision an adult passenger is properly seated in the front passen- requiring air bag deployment.
Page 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Drivers and adult passengers should verify that the PAD WARNING! Indicator Light is not illuminated when an adult is riding in the front passenger seat. If an adult occupant’s weight Never place a rear facing infant seat in front of an air is transferred to another part of the vehicle (like the door bag.
Page 72
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If there is a fault present in the air bag system, the Air Bag Driver And Passenger Advanced Front Air Bag Warning Light (a red light located in the center of the Inflator Units instrument cluster directly in front of the driver) will be The Driver And Passenger Advanced Front Air Bag...
Page 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 The Advanced Front Air Bag gas is vented through the and damage by themselves are not good indicators of vent holes in the sides of the air bag. In this way, the air whether or not an air bag should have deployed.
Page 74
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The following requirements must be strictly adhered to: WARNING! • Do not modify the front passenger seat assembly or If your vehicle is equipped with left and right components in any way. Supplemental Side Air Bag Inflatable Curtains •...
Page 75
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Enhanced Accident Response System WARNING! In the event of an impact causing air bag deployment, if the communication network remains intact, and the Unapproved modifications or service procedures to power remains intact, depending on the nature of the the front passenger seat assembly, its related compo- event the ORC will determine whether to have the nents or seat cover may inadvertently change the air...
Page 76
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs They are not permanent and normally heal quickly. The Advanced Front Air Bags are designed to deflate However, if you haven’t healed significantly within a immediately after deployment. few days, or if you have any blistering, see your doctor immediately.
Page 77
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Do not drive your vehicle after the air bags have de- Maintaining Your Air Bag System ployed. If you are involved in another collision, the air WARNING! bags will not be in place to protect you. •...
Page 78
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light WARNING! (Continued) You will want to have the air bags ready to • Do not attempt to modify any part of your air bag inflate for your protection in a collision. The system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 • Whether or not the driver and passenger safety belts NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint were buckled/fastened; Controller (ORC) may also be disabled. The air bags may •...
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To read data recorded by an EDR, special equipment is WARNING! required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, In a collision, an unrestrained child, even a tiny baby, such as law enforcement, that have the special equip- can become a projectile inside the vehicle.
Page 81
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Infants And Child Restraints held in the vehicle by the lap/shoulder belt or the Safety experts recommend that children ride rearward- LATCH child restraint anchor system. Refer to “Lower facing in the vehicle until they are two years old or until Anchors and Tether for CHildren (LATCH)”.
Page 82
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE remain in a forward-facing child seat with a harness for over the front of the seat when their back is against the as long as possible, up to the highest weight or height seat back, should use the lap/shoulder belt in a rear seat.
Page 83
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Here are some tips on getting the most out of your child WARNING! restraint: • Improper installation can lead to failure of an • Before buying any restraint system, make sure that it infant or child restraint.
Page 84
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have features for installation using the vehicle’s seat WARNING! belts. Child restraints having tether straps and hooks for connection to the top tether anchorages have been avail- When your child restraint is not in use, secure it in able for some time.
Page 85
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 If you are installing LATCH-compatible child restraints The rear seat lower anchorages are round bars, located at in adjacent rear seating positions, you can use the the rear of the seat cushion where it meets the seatback, LATCH anchors or the vehicle’s seat belt for the outboard and are just visible when you lean into the rear seat to position, but you must use the vehicle’s seat belt at the...
Page 86
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, there are tether strap anchorages behind each means of adjusting the tension in the strap. Forward- rear seating position located on the back of the seat. facing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
Page 87
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 downward into the seat, removing slack in the straps will make a ratcheting noise if you extract the entire belt according to the child restraint manufacturer’s instruc- from the retractor and then allow the belt to retract into tions.
Page 88
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE through the belt path of the child restraint. Slide the latch 2. Finally, pull on any excess webbing to tighten the lap plate into the buckle until you hear a “click.” Next, portion around the child restraint.
Page 89
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 • Route the tether strap to provide the most direct path WARNING! for the strap between the anchor and the child seat, preferably between the head restraint posts under- An incorrectly anchored tether strap could lead to neath the head restraint.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS CAUTION! A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. Drive moderately during the first 300 miles (500 km).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Exhaust Gas WARNING! • Do not leave children or animals inside parked WARNING! vehicles in hot weather. Interior heat build-up may Exhaust gases can injure or kill. They contain carbon cause serious injury or death. monoxide (CO), which is colorless and odorless.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The WARNING! (Continued) Vehicle • If it is necessary to sit in a parked vehicle with the Seat Belts engine running, adjust your heating or cooling Inspect the belt system periodically, checking for cuts, controls to force outside air into the vehicle.
Page 93
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place • Always make sure that floor mats are properly the blower control on high speed. You should be able to attached to the floor mat fasteners.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE lodged in the tread or sidewall. Inspect the tread for cuts WARNING! (Continued) and cracks. Inspect sidewalls for cuts, cracks and bulges. • Always make sure that objects cannot fall into the Check the wheel nuts for tightness.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......99 Uconnect™ Phone — If Equipped ..103 Inside Day/Night Mirror .
Page 96
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command — If Equipped ... 133 60/40 Split Folding Rear Seat With Fold-Flat Feature ......149 Voice Command System Operation .
Page 97
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Headlights With Wipers (Available With Windshield Wipers And Washers ..164 Automatic Headlights Only) ... . 160 Windshield Wiper Operation .
Page 98
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate ..... . . 174 Garage Door Opener — If Equipped ..184 To Resume Speed .
Page 99
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Closing Sunroof — Express ... . . 194 Opening The Sky Slider™ ....199 Closing Sunroof —...
Page 100
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Window Features ....214 Rear Window Defroster ....215 Rear Window Wiper/Washer .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle).
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Outside Mirrors Power Mirrors To receive maximum benefit, adjust the outside mirror(s) The power mirror switch is located on the driver’s door to center on the adjacent lane of traffic and a slight trim panel.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Models With Express Window Feature Models Without Express Window Feature Press and release the mirror select button marked L (left) Press the mirror select button marked L (left) or R (right) or R (right) and then press one of the four arrow buttons and then press one of the four arrow buttons to move the to move the mirror in the direction the arrow is pointing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 2. Unclip the visor from the center clip. 3. Pull the sun visor toward the inside rearview mirror to extend it. Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-free, in- vehicle communications system.
Page 106
• www.dodge.com/uconnect system. Only one linked (or paired) mobile phone can be used with the system at a time. The system is available in • www.jeep.com/uconnect English, Spanish, or French languages. • or call 1–877–855–8400 WARNING! Uconnect™...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Uconnect™ Phone Button The Uconnect™ Phone is fully integrated with the vehi- The radio or steering wheel controls (if cle’s audio system. The volume of the Uconnect™ Phone equipped) will contain the two control buttons can be adjusted either from the radio volume control (Uconnect™...
Page 108
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For certain operations, compound commands can be Help Command used. For example, instead of saying “Setup” and then If you need assistance at any prompt, or if you want to “Pair a Device”, the following compound command know your options at any prompt, say “Help”...
Page 109
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • For identification purposes, you will be prompted to To complete the pairing process, you will need to refer- ence your mobile phone Owner’s Manual. The give the Uconnect™ Phone a name for your mobile Uconnect™...
Page 110
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the name of the Dial By Saying A Number person you want to call. • Press the button to begin. • After the “Ready” prompt and the following beep, say •...
Page 111
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • After the “Ready” prompt and the following beep, say The Uconnect™ Phone will allow you to enter up to 32 “Phonebook New Entry”. names in the phonebook with each name having up to four associated phone numbers and designations.
Page 112
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Automatic download and update, if supported, begins • This downloaded phonebook cannot be edited or as soon as the Bluetooth wireless phone connection is deleted on the Uconnect™ Phone. These can only be made to the Uconnect™...
Page 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • Next, choose the number designation (home, work, • Press the button to begin. mobile, or other) that you wish to edit. • After the “Ready” prompt and the following beep, say • When prompted, recite the new phone number for the “Phonebook Delete”.
Page 114
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Note that only the phonebook entry in the current List All Names In The Uconnect™ Phonebook language is deleted. • Press the button to begin. • Automatic downloaded phonebook entries cannot be •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Phone Call Features Answer Or Reject An Incoming Call — Call The following features can be accessed through the Currently In Progress Uconnect™ Phone if the feature(s) are available on your If a call is currently in progress and you have another mobile service plan.
Page 116
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE in progress. To go back to the first call, refer to “Toggling Conference Call Between Calls” in this section. To combine two calls, refer When two calls are in progress (one active and one on to “Conference Call”...
Page 117
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Call Termination Call Continuation To end a call in progress, momentarily press the Call continuation is the progression of a phone call on the button. Only the active call(s) will be terminated and if Uconnect™...
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone Features Emergency Assistance If you are in an emergency and the mobile phone is Language Selection reachable: To change the language that the Uconnect™ Phone is • Pick up the phone and manually dial the emergency using: number for your area.
Page 119
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Canada and 060 for Mexico). The number dialed may Towing Assistance not be applicable with the available mobile service and If you need towing assistance: area. • Press the button to begin. • If supported, this number may be programmable on •...
Page 120
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Paging When calling a number with your Uconnect™ Phone that To learn how to page, refer to “Working with Automated normally requires you to enter in a touch-tone sequence Systems”. Paging works properly except for pagers of on your mobile phone keypad, you can press the certain companies, which time out a little too soon to button and say the sequence you wish to enter, followed...
Page 121
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 The Uconnect™ Phone will then send the corresponding Turning Confirmation Prompts ON/OFF phone number associated with the phonebook entry, as Turning confirmation prompts off will stop the system tones over the phone. from confirming your choices (e.g., the Uconnect™ Phone will not repeat a phone number before you dial it).
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using The Mobile Phone Keypad Mute/Un-Mute (Mute OFF) You can dial a phone number with your mobile phone When you mute the Uconnect™ Phone, you will still be keypad and still use the Uconnect™ Phone (while dialing able to hear the conversation coming from the other via the mobile phone keypad, the user must exercise party, but the other party will not be able to hear you.
Page 123
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 • When prompted, say “List Phones”. from your Uconnect™ Phone paired mobile phone to the Uconnect™ Phone or vice versa, press the button • The Uconnect™ Phone will play the phone names of and say “Transfer Call”.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone Things You Should Know About Your Uconnect™ call. If the selected phone is not available, the Phone Uconnect™ Phone will return to using the highest Uconnect™...
Page 125
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 You can either press the Uconnect™ Phone button to Voice Command restore the factory setting or repeat the words and • For best performance, adjust the rearview mirror to phrases when prompted by the Uconnect™ Phone. For provide at least ⁄...
Page 126
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • dry weather condition. • You can say “O” (letter “O”) for “0” (zero). •...
Page 127
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 • fully closed windows, Uconnect™ Phone can read or send new messages on • dry weather conditions, and your phone. • operation from the driver’s seat. Read Messages: • Performance, such as audio clarity, echo, and loudness If you receive a new text message while your phone is to a large degree rely on the phone and network, and connected to Uconnect™...
Page 128
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Send Messages: List of Preset Messages: You can send messages using Uconnect™ Phone. To send 1. Yes a new message: 2. No • Press the button. 3. Where are you? • After the “Ready” prompt and the following beep, say “SMS Send”...
Page 129
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 • After the “Ready” prompt and the following beep, say 13. I’ll be late “Setup, SMS Incoming Message Announcement,” you 14. Are you there yet? will then be given a choice to change it. 15.
Page 130
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 131
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129...
Page 132
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 133
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 134
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 General Information NOTE: Take care to speak into the Voice Interface This device complies with Part 15 of the FCC rules and System as calmly and normally as possible. The ability of RSS 210 of Industry Canada. Operation is subject to the the Voice Interface System to recognize user voice com- following conditions: mands may be negatively affected by rapid speaking or a...
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the Voice Command button, listen dows are closed, and the heater/air conditioning fan is for the beep, and say your command.
Page 137
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 3. Use the ON/OFF VOLUME rotary knob to adjust the Radio AM volume to a comfortable level while the Voice Command To switch to the AM band, say “AM” or “Radio AM”. In system is speaking.
Page 138
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Menu Radio” (to switch to the radio menu) Disc To switch to the disc mode, say “Disc”. In this mode, you • “Main Menu” (to switch to the main menu) may say the following commands: Satellite Radio •...
Page 139
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 • “Switch to system setup” − “Continue” (to continue recording) • “Change to setup” − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) • “Main menu setup” or —...
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect™ vehicle. Voice “Voice Training” feature may be used. WARNING! 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Driver’s Power Seat — If Equipped Adjusting The Seat Forward Or Rearward The power seat switch is located on the outboard side of The seat can be adjusted both forward and rearward. the seat near the floor. Use this switch to move the seat up Push the seat switch forward or rearward, the seat will or down, forward or rearward or to tilt the seat.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passenger Power Seat — If Equipped CAUTION! Vehicle’s equipped with passenger power seats can only be adjusted forward and backward. Do not place any article under a power seat or impede its ability to move as it may cause damage to WARNING! the seat controls.
Page 143
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 You can choose from HIGH, LOW or OFF heat settings. NOTE: When a heat setting is selected, heat will be felt Amber indicator lights in each switch indicate the level of within two to five minutes. heat in use.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front Seat Adjustments While sitting in the seat, lift up on the bar and move the For models equipped with manual seats, the driver and seat forward or rearward. Release the bar once you have passenger seats can be adjusted forward or rearward by reached the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Front Seat — Manual Recline WARNING! To recline the seatback, lean forward slightly and lift the lever. Then lean back to the position desired and release Do not ride with the seatback reclined so that the the lever.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar Support — If Equipped Fold-Flat Front Passenger Seat — If Equipped For models equipped with manual lumbar the support This feature allows the front passenger seatback to fold lever is located on the inboard side of the seat. Turn the flat for extended cargo space.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Head Restraints Active Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury Active Head Restraints are passive, deployable compo- by restricting head movement in the event of a rear nents, and vehicles with this equipment cannot be readily impact.
Page 148
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head For comfort the Active Head Restraints can be tilted restraint. To lower the head restraint, press the adjust- forward and backward. To tilt the head restraint closer to ment button, located at the base of the head restraint, and the back of your head, pull forward on the bottom of the push downward on the head restraint.
Page 149
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
Page 150
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Active Head Restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the Ac- tive Head Restraint ensure that all cargo is se- cured, as loose cargo could contact the Active Head Restraint during sudden stops.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 • Refer to “Occupant Restraints” in “Things To Know be sure that the front seats are fully upright and posi- Before Starting Your Vehicle” for information on tether tioned forward. This will allow the rear seat to fold down routing.
Page 152
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Pull the release strap (toward the front of the vehicle). To Raise The Rear Seat NOTE: If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Recliner Adjustment WARNING! The rear seatback also reclines for additional passenger comfort. Pull the release strap while sitting in the rear Do not ride with the seatback reclined so that the seat to recline the seatback. shoulder belt is no longer resting against your chest.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE recall either of the two pre-programmed memory profiles 1. Turn the ignition ON. by pressing the appropriate side of the switch. 2. Adjust all memory profile settings to desired prefer- ences (i.e., seat, side mirror and radio station presets). 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 3. Press and release the SET button on the memory Linking And Unlinking The Remote Keyless Entry switch, then press the side of the rocker switch labeled (2) Transmitter To Memory within five seconds. The EVIC, if equipped, will display Your Remote Keyless Entry (RKE) transmitters can be which memory position is being set.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Your RKE transmitters can be unlinked to the To recall the memory settings for driver one, press memory setting by pressing the SET button followed by MEMORY button number 1 or the UNLOCK button on the UNLOCK button on the RKE transmitter in Step 4 the RKE transmitter linked to memory position 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Easy Entry/Exit Seat between 0.9 in and 2.7 in (23 mm and 68 mm) forward (Available With Memory Seat Only) of the rear stop. The seat will return to its previously This feature provides automatic driver seat positioning to set position when you insert the key into the ignition enhance driver mobility when entering and exiting the switch and turn it out of the LOCK position.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD 2. Outside of the vehicle, locate the safety latch lever Two latches must be released to open the hood. between the grille and hood opening (left of center when facing hood).
Page 159
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Use the hood prop rod to secure the hood in the open WARNING! position. Place the upper end of the prop rod in the hole on the underside of the hood. Be sure the hood is fully latched before driving your vehicle.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlights And Parking Lights Turn the end of the multifunction lever to the first detent Multifunction Lever for parking light operation. Turn the end of the lever to The multifunction lever on the left side of the steering the second detent for headlight operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, turn the end of the multifunction lever to the AUTO position (third detent).
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights With Wipers Headlight Time Delay — If Equipped (Available With Automatic Headlights Only) This feature is particularly useful when exiting your When this feature is active, the headlights will turn on vehicle in an unlit area. It provides the safety of headlight approximately 10 seconds after the wipers are turned on illumination for about 90 seconds after turning the igni- if the multifunction lever is placed in the AUTO position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 (EVIC)/Customer-Programmable Features” in “Under- standing Your Instrument Panel” for further information. Daytime Running Lights — If Equipped The headlights will turn on as Daytime Running Lights (DRL) and operate at lower intensity whenever the ignition is ON, the engine is running, the headlight switch is off, the parking brake is released and the shift lever is in any position except PARK.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals NOTE: If either light remains on and does not flash, or Move the multifunction lever up or down and the arrows there is a very fast flash rate, check for a defective outside on each side of the instrument cluster flash to show light bulb.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: If the multifunction lever is held in the flash-to- pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds before activating the flash-to-pass function again. Instrument Panel Dimmer Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights...
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UNLOCK button on the Remote Keyless Entry (RKE) WINDSHIELD WIPERS AND WASHERS transmitter is pressed, or when the dimmer control is The windshield wiper/washer control lever is located on turned completely upward to the second detent. the right side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Windshield Wiper Operation NOTE: The wipers will automatically return to the Rotate the end of the lever upward to the second detent “park” position if you turn OFF the ignition switch while past the intermittent settings for low-speed wiper opera- they are operating.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 NOTE: The wiper delay times depend on vehicle speed. WARNING! If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Sudden loss of visibility through the windshield could lead to a collision.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The mist feature does not activate the washer Rain Sensing Wipers — If Equipped pump; therefore, no washer fluid will be sprayed on the This feature senses moisture on the windshield and windshield.
Page 171
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 NOTE: The rain-sensing system has protective features for the • The rain-sensing feature will not operate when the wiper blades and arms. It will not operate under the wiper speed is in the low or high position. following conditions: •...
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Neutral Wipe Inhibit — The rain-sensing feature will Headlights With Wipers not operate when the ignition is ON, and the shift (Available With Automatic Headlights Only) lever is in the NEUTRAL position, and the vehicle When this feature is active, the headlights will turn on speed is less than 5 mph (8 km/h), unless the wiper approximately 10 seconds after the wipers are turned on...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 TILT STEERING COLUMN To unlock the steering column, push the control handle This feature allows you to tilt the steering column downward. To tilt the steering column, move the steering upward or downward. The tilt control handle is located wheel upward or downward as desired.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN To unlock the steering column, pull the lever downward. This feature allows you to tilt the steering column To tilt the steering column, move the steering wheel upward or downward. It also allows you to lengthen or upward or downward as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 ELECTRONIC SPEED CONTROL — IF EQUIPPED NOTE: In order to ensure proper operation, the Elec- When engaged, the Electronic Speed Control takes over tronic Speed Control System has been designed to shut accelerator operations at speeds greater than 25 mph down if multiple Speed Control functions are operated at (40 km/h).
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate WARNING! A soft tap on the brake pedal, pushing the CANCEL button, or normal brake pressure while slowing the Leaving the Electronic Speed Control system on vehicle will deactivate Electronic Speed Control without when not in use is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Pressing the RES (+) button once will result in a 1 mph Using Electronic Speed Control On Hills (2 km/h) increase in set speed. Each subsequent tap of The transmission may downshift on hills to maintain the the button results in an increase of 1 mph (2 km/h).
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE REAR PARK ASSIST — IF ParkSense Sensors EQUIPPED The four ParkSense sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is The ParkSense Rear Park Assist system provides visual within the sensors’...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 The ParkSense Warning Display is located in the Instru- ParkSense Display ment cluster’s EVIC display. It provides both visual and When the vehicle is in REVERSE, the warning display audible warnings to indicate the distance between the will turn ON indicating the system status.
Page 180
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Park Assist Off Slow Tone The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 181
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle:...
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING ALERTS Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than (in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm) Audible Alert None Single 1/2 Slow Fast Continuous...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 When the ParkSense switch is pressed to “Electronic Vehicle Information Center (EVIC)” in “Un- disable the system, the instrument cluster will derstanding Your Instrument Panel” for further informa- display the “PARK ASSIST OFF” message for tion.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Clean the ParkSense sensors regularly, taking care ParkSense System Usage Precautions not to scratch or damage them. The sensors must not NOTE: be covered with ice, snow, slush, mud, dirt or debris. •...
Page 185
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 CAUTION! WARNING! • ParkSense is only a parking aid and it is unable • Drivers must be careful when backing up even to recognize every obstacle, including small ob- when using the ParkSense Rear Park Assist Sys- stacles.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED WARNING! (Continued) HomeLink replaces up to three hand-held transmitters • Before using the ParkSense Rear Park Assist that operate devices such as garage door openers, motor- System, it is strongly recommended that the ball ized gates, lighting or home security systems.
Page 187
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 HomeLink Buttons/Sunvisor/Headliner HomeLink Buttons/Overhead Consoles NOTE: HomeLink is disabled when the Vehicle Secu- rity Alarm is active.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Before You Begin Programming HomeLink NOTE: • Erasing all channels should only be performed when Be sure that your vehicle is parked outside of the garage before you begin programming. programming HomeLink for the first time. Do not erase channels when programming additional buttons.
Page 189
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 3. Simultaneously press and hold both the Homelink button you want to program and the hand-held transmit- ter button. 4. Continue to hold both buttons and observe the indi- cator light. The Homelink indicator will flash slowly and then rapidly after Homelink has received the fre- quency signal from the hand-held transmitter.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: You have 30 seconds in which to initiate the next 2. Press and hold the desired HomeLink button until step after the LEARN button has been pressed. the indicator light begins to flash after 20 seconds. Do not release the button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 4. Continue to hold both buttons and observe the indi- Reprogramming A Single HomeLink Button cator light. The Homelink indicator will flash slowly To reprogram a channel that has been previously trained, and then rapidly after Homelink has received the fre- follow these steps: quency signal from the hand-held transmitter.
Page 192
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to pick up the signal during programming. Similar to this 4. Watch for the HomeLink indicator to change flash Canadian law, some U.S. gate operators are designed to rates. When it changes, it is programmed. It may take up time-out in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Reprogramming A Single HomeLink Button Security To reprogram a channel that has been previously trained, It is advised to erase all channels before you sell or turn follow these steps: in your vehicle. 1.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips WARNING! If you are having trouble programming HomeLink , here • Your motorized door or gate will open and close are some of the most common solutions: while you are programming the universal trans- •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The power sunroof switch is located between the sun Canada RSS-210. Operation is subject to the following visors on the overhead console.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express WARNING! Press the switch rearward and release it within one-half • Never leave unattended children in a vehicle with second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- the key in the ignition switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 position. The sunroof will close fully and stop automati- Pinch Protect Override cally. This is called “Express Close”. During Express If a known obstruction (ice, debris, etc.) prevents closing Close operation, any movement of the switch will stop and moves the sunroof in the opposite direction, press the sunroof.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation open. For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch Wind Buffeting will remain active for 45 seconds after the ignition switch Wind buffeting can be described as the perception of is turned to the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 Sky Slider™ Usage Precautions CAUTION! (Continued) NOTE: • Opening the Sky Slider™ when damp, wet, or • The system will not operate when ambient tempera- dirty can cause stains, mildew, and damage to the ture is at –4°F (–20°C) or lower.
Page 200
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • If potential danger exists while opening or closing Failure to follow these warnings can result in injuries the Sky Slider™ in Automatic Mode, press and that are serious or fatal to you, your passengers, and release the switch immediately to interrupt the others around you: operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Sky Slider™ Control Opening The Sky Slider™ The Sky Slider™ switch is located between the sun visors Using Automatic Mode on the overhead console. Press the switch rearward and release it within one-half second and the Sky Slider™...
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using Operator Mode Using Operator Mode Press the switch rearward and hold it, the Sky Slider™ If the Sky Slider™ is open from the front, press the switch will open from the front and move toward the rear of the forward and hold it, the Sky Slider™...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 completely. The left motor facing forward will close the Wind Buffeting top when it is open from the rear of the vehicle. The right Wind buffeting can be described as the perception of motor will close the top when it is open from the front of pressure on the ears or a helicopter-type sound in the the vehicle.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLET Insert the cigar lighter or accessory plug into the outlet Your vehicle is equipped with a fused 12 Volt (13 Amp) for use to ensure proper operation. power outlet. This power outlet is located on the instru- NOTE: To ensure proper operation a MOPAR knob ment panel, below the climate controls.
Page 205
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
Page 206
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • After the use of high power draw accessories, or • Many accessories that can be plugged in draw long periods of the vehicle not being started (with power from the vehicle’s battery, even when not in accessories still plugged in), the vehicle must be use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 CUPHOLDERS The rear passengers have cupholders at the rear of the There are two cupholders for the front seat passengers, center console. located in the center console. Rear Cupholders Front Cupholders...
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Front Storage Compartment The front storage compartment (located on the left side of Glove Box Storage Compartment the instrument panel) can hold cell phones, PDAs, and The glove box storage compartment is located on the other small items.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Console Storage Compartment The center console has a removable storage tray which To open, press the latch and lift the cover. can hold cell phones, PDAs, and other small items. Center Console Removable Storage Tray...
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To provide additional storage area, each rear seat can be WARNING! folded flat. This allows for extended cargo space and still maintains some rear seating room. Refer to “Seats” in Do not operate this vehicle with a console compart- “Understanding the Features of Your Vehicle”...
Page 211
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 4. Turn over the cover and reinstall it. NOTE: You can install the cover with either side facing upward. 5. With the cover seated in the floor, pull upward on loops and twist them one-quarter turn so that they are no longer parallel to the slots in the cover.
Page 212
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Hooks And Loops The tie-downs located on cargo area floor should be used to secure loads safely when the vehicle is moving. Cargo Tie-Down Loops Cargo tie-down loops are located on the trim panels. Cargo Tie-Down Hooks...
Page 213
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 WARNING! WARNING! • Cargo tie-downs are not safe anchors for a child The weight and position of cargo and passengers can seat tether strap. In a sudden stop or accident, a change the vehicle center of gravity and vehicle tie-down could pull loose and allow the child seat handling.
Page 214
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cover, when extended, covers the cargo area to keep WARNING! (Continued) items out of sight. Notches in the trim panels near the • Do not pile luggage or cargo higher than the top of liftgate opening secure the extended cover in place.
Page 215
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Next, grab the cover handle and pull the cover toward you. As the cover nears the liftgate opening, guide the rear attachment posts (on both ends of the cover) into the notches in the trim panels. Then, lower the cover to position the posts into the bottom of the notches and release the handle.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In a collision, a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 Rotate the switch upward past the first detent to defroster automatically turns off after approximately activate the rear washer. The washer pump will 10 minutes. For an additional five minutes of operation, continue to operate as long as the switch is held press the button a second time.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Crossbars should always be used whenever cargo is CAUTION! (Continued) placed on the roof rack. Check the straps frequently to be • Do not use scrapers, sharp instruments, or abra- sure that the load remains securely attached. sive window cleaners on the interior surface of the NOTE: Crossbars are offered by MOPAR accessories.
Page 219
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 CAUTION! (Continued) WARNING! • Long loads, which extend over the windshield, Cargo must be securely tied down before driving such as wood panels or surfboards, should be your vehicle. Improperly secured loads can fly off the secured to both the front and rear of the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....222 Compass Display / ECO (Fuel Saver Mode) — If Equipped ..244 Instrument Cluster .
Page 222
220 UNDERSTANDING YOUR INSTRUMENT PANEL Media Center 230 (REQ) — AM/FM Stereo Media Center 730N/430/430N (RHR/RER/ Radio And 6–Disc CD/DVD Changer RBZ/RHB) CD/DVD/HDD/NAV — If (MP3/WMA AUX Jack) ....254 Equipped .
Page 223
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Media Center 130 With Satellite Radio Steering Wheel Audio Controls ... . 298 (Sales Code RES+RSC)....282 Radio Operation .
224 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should 1. Fuel Gauge determine the proper tire inflation pressure for those The fuel gauge shows level of fuel in tank when ignition tires.) switch is in the ON/RUN position.
Page 227
UNDERSTANDING YOUR INSTRUMENT PANEL 225 maintain correct tire pressure, even if under-inflation has tires or wheels on your vehicle, to ensure that the not reached the level to trigger illumination of the TPMS replacement or alternate tires and wheels allow the TPMS low tire pressure telltale.
Page 228
226 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Electronic Throttle Control (ETC) Light 6. Malfunction Indicator Light (MIL) This light informs you of a problem with the The Malfunction Indicator Light (MIL) is part of Electronic Throttle Control (ETC) system. If a an onboard diagnostic system, called OBD, that problem is detected, the light will come on monitors engine and automatic transmission con-...
Page 229
UNDERSTANDING YOUR INSTRUMENT PANEL 227 7. High Beam Indicator CAUTION! This indicator shows that the high beam head- lights are on. Pull the multifunction control lever Prolonged driving with the MIL on could cause on the left side of the steering column toward you to damage to the engine control system.
Page 230
228 UNDERSTANDING YOUR INSTRUMENT PANEL If the vehicle electronics sense that the vehicle is driven NOTE: • The “ESC Off Indicator Light” and the “ESC more than 1 mile (1.6 km) with either turn signal on, a continuous chime will sound to alert you to turn the Activation/Malfunction Indicator Light”...
Page 231
UNDERSTANDING YOUR INSTRUMENT PANEL 229 the charging system light remains on, it means that the 14. Anti-Lock Brake (ABS) Light vehicle is experiencing a problem with the charging This light monitors the Anti-Lock Brake System system. Obtain SERVICE IMMEDIATELY. See an autho- (ABS).
Page 232
230 UNDERSTANDING YOUR INSTRUMENT PANEL green area, you are driving the vehicle in a fuel efficient 18. TOW/HAUL Indicator — If Equipped manner. Before the pointer reaches the red area, ease up This light will illuminate when selecting on the accelerator to prevent engine damage. TOW/HAUL.
Page 233
UNDERSTANDING YOUR INSTRUMENT PANEL 231 21. SERV (Service) 4WD Indicator Light — If Equipped If the light turns on while driving, safely pull over and The “SERV 4WD Indicator Light” will turn on stop the vehicle. If the A/C system is on, turn it off. Also, when the ignition key is turned to the ON/ shift the transmission into NEUTRAL and idle the ve- RUN position and it will stay on for two...
Page 234
232 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! WARNING! Driving with a hot engine cooling system could A hot engine cooling system is dangerous. You or damage your vehicle. If the temperature gauge reads others could be badly burned by steam or boiling “H”...
Page 235
UNDERSTANDING YOUR INSTRUMENT PANEL 233 display. Trip A or Trip B will appear when in the trip CAUTION! odometer mode. On vehicles equipped with a Base Cluster, press and release it once again to display the Continuous driving with the Transmission Tempera- outside temperature.
Page 236
234 UNDERSTANDING YOUR INSTRUMENT PANEL torque split of 42% front axle and 58% rear axle. It can the repair/service, so that you can be sure that it is redirect up to 100% of torque to the front or rear axle, if properly reset, or that the door jamb sticker is accurate if necessary.
Page 237
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Center (EVIC) messages when the appropriate conditions gASCAP Message exist. Refer to Electronic Vehicle Information Center If the vehicle diagnostic system determines that the fuel (EVIC) for further information. filler cap is loose, improperly installed, or damaged, the words “gASCAP”...
Page 238
236 UNDERSTANDING YOUR INSTRUMENT PANEL CHAngE OIL Message 2. Fully depress the accelerator pedal slowly three (Base And Mid Line Clusters Only) times within 10 seconds. Your vehicle is equipped with an engine oil change 3. Turn the ignition switch to the LOCK position. indicator system.
Page 239
UNDERSTANDING YOUR INSTRUMENT PANEL 237 the driver’s seat belt is unbuckled, a chime will sound. System (ABS) / Electronic Stability Control (ESC) system. After the bulb check or when driving, if the driver seat In this case, the light will remain on until the condition belt remains unbuckled, the Seat Belt Warning Light will has been corrected.
Page 240
238 UNDERSTANDING YOUR INSTRUMENT PANEL If brake failure is indicated, immediate repair is neces- unless the parking brake is applied or a brake fault is sary. detected. If the light does not illuminate, have the light inspected by an authorized dealer. WARNING! The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN posi-...
UNDERSTANDING YOUR INSTRUMENT PANEL 239 33. Air Bag Warning Light ELECTRONIC VEHICLE INFORMATION CENTER This light will turn on for four to eight seconds (EVIC) — IF EQUIPPED as a bulb check when the ignition switch is first The Electronic Vehicle Information Center (EVIC) fea- turned to ON/RUN.
Page 242
240 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a The system allows the driver to select information by variety of useful information by pressing the switches pressing the following buttons mounted on the steering mounted on the steering wheel. The EVIC consists of the wheel: following: •...
UNDERSTANDING YOUR INSTRUMENT PANEL 241 MENU Button COMPASS Button Press and release the MENU button to advance Press release COMPASS/ the display to each of the EVIC Main Menu TEMPERATURE button to display one of eight features. Upon reaching the last item in the compass readings and the outside temperature Main Menu the EVIC will advance to the first when the current screen is not the Compass/...
Page 244
242 UNDERSTANDING YOUR INSTRUMENT PANEL • Left Rear Turn Signal Lamp Out (with a single chime) • Personal Settings Not Avail – Vehicle Not in Park — automatic transmission • Right Front Turn Signal Lamp Out (with a single • Personal Settings Not Avail – Vehicle in Motion — chime) manual transmission •...
UNDERSTANDING YOUR INSTRUMENT PANEL 243 • Service TPM System (with a single chime). Refer to Unless reset, this message will continue to display each “Tire Pressure Monitoring System” in “Starting And time you turn the ignition switch to the ON position. To Operating”.
244 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC Main Menu NOTE: For features in the EVIC that can be reset To step to each main menu feature press and release the (Average Fuel Economy and Elapsed Time), the EVIC MENU button once for each step. A step from the last prompts a reset with a SELECT button graphic and the item in the list will cause the first item in the feature list word RESET next to it.
Page 247
UNDERSTANDING YOUR INSTRUMENT PANEL 245 and audio information (if the radio is on)/ECO if the This feature allows you to monitor when you are driving EVIC display is not already displaying this screen. in a fuel efficient manner, and it can be used to modify driving habits in order to increase fuel economy.
Page 248
246 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Compass Calibration 5. Complete one or more 360–degree turns (in an area If the compass appears erratic and the “CAL” indicator free from large metal or metallic objects) until the “CAL” does not appear in the EVIC display, you must put the indicator turns off.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 3. Press the DOWN button until “Compass Variance” displays in the EVIC. 4. Press and release the SELECT button until the proper variance zone is selected according to the map. NOTE: The Variance Values will wrap around from 15 back to 1.
248 UNDERSTANDING YOUR INSTRUMENT PANEL Distance To Empty (DTE) Tire PSI Press and release the MENU button until Tire PSI is Shows the estimated distance that can be traveled with displayed. the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous Tire pressure information is displayed as follows: and average fuel economy, according to the current fuel...
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Elapsed Time System Status Shows the total elapsed time of travel since the last reset. Displays SYSTEM OK if there are no active Warning Elapsed time will increment when the ignition switch is Messages stored. Pressing and releasing the DOWN in the RUN or START position.
Page 252
250 UNDERSTANDING YOUR INSTRUMENT PANEL Use the DOWN button to display one of the following RKE Unlock choices: When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the Remote Keyless Language Entry (RKE) transmitter UNLOCK button.
Page 253
UNDERSTANDING YOUR INSTRUMENT PANEL 251 button until “ON” or “OFF” appears. Refer to “Driver Headlamp Off Delay Memory Seat” in “Understanding The Features Of Your When this feature is selected, the driver can choose to Vehicle” for more information. have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle.
Page 254
252 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Turning the headlights on during the daytime and power outlets will remain active for up to 10 minutes causes the instrument panel lights to dim. To increase the after the ignition switch is turned to the LOCK position. brightness, refer to “Lights”...
Page 255
UNDERSTANDING YOUR INSTRUMENT PANEL 253 make your selection, press and release the SELECT Display Units In button. Refer to “Rear Park Assist System” in “Under- The EVIC can be changed between English and Metric standing The Features Of Your Vehicle” for system func- units of measure.
254 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 230 (REQ) — AM/FM STEREO Operating Instructions - Radio Mode RADIO AND 6–DISC CD/DVD CHANGER NOTE: The ignition switch must be in the ON or ACC (MP3/WMA AUX JACK) position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 257
UNDERSTANDING YOUR INSTRUMENT PANEL 255 SEEK Buttons Voice Command Button Uconnect™ Phone — If Press and release the SEEK buttons to search for the next Equipped listenable station in AM/FM mode. Press the right switch Press this button to operate the Uconnect™ Phone feature to seek up and the left switch to seek down.
Page 258
256 UNDERSTANDING YOUR INSTRUMENT PANEL If your vehicle is not equipped with or this feature is not 4. Adjust the minutes using the right side TUNE/ available on your vehicle, a “Not Equipped With SCROLL control knob. Press the TUNE/SCROLL control Uconnect Phone”...
Page 259
UNDERSTANDING YOUR INSTRUMENT PANEL 257 TUNE Control Push the rotary TUNE/SCROLL control knob a fourth Turn the rotary TUNE/SCROLL control knob clockwise time and BALANCE will display. Turn the TUNE/ to increase or counterclockwise to decrease the frequency. SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers.
Page 260
258 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following Program Type 16-Digit Character Display format types: Public Public Program Type 16-Digit Character Display Rhythm and Blues R & B No program type or Religious Music Rel Musc None undefined...
Page 261
UNDERSTANDING YOUR INSTRUMENT PANEL 259 • DVD Play Options - Selecting the DVD Play Options If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be will display the following: exited and the radio will tune to the preset station. •...
Page 262
260 UNDERSTANDING YOUR INSTRUMENT PANEL • VES™ Power - Allows you to turn VES™ ON and Menu Language — If Equipped OFF (if equipped). Selecting this item will allow the user to choose the default startup DVD menu language (effective only if •...
Page 263
UNDERSTANDING YOUR INSTRUMENT PANEL 261 Subtitle Language — If Equipped AutoPlay — If Equipped Selecting this item allows you to choose a default subtitle When this is set to On and a DVD video is inserted, it will language (effective only if the language is supported by bypass the DVD menu screen and automatically play the the disc).
262 UNDERSTANDING YOUR INSTRUMENT PANEL and press and release that button. If a button is not Buttons 1 - 6 selected within five seconds after pressing the SET but- These buttons tune the radio to the stations that you ton, the station will continue to play but will not be commit to pushbutton memory {12 AM, 12 FM, and 12 stored into pushbutton memory.
Page 265
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Radio display will show LOADING DISC when the disc CAUTION! is loading and “READING DISC” when the radio is reading the disc. The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate CAUTION! “Disc Hot”...
264 UNDERSTANDING YOUR INSTRUMENT PANEL The disc can be ejected with the radio and ignition OFF. RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will SEEK Button (CD MODE) begin to fast forward until FF is released, or RW or Press the right SEEK button for the next selection on the another CD button is pressed.
Page 267
UNDERSTANDING YOUR INSTRUMENT PANEL 265 Supported Medium Formats (File Systems) Multisession disc formats are supported by the radio. The medium formats supported by the radio are ISO 9660 Multisession discs may contain combinations of normal Level 1 and Level 2 and includes the Joliet extension. CD audio tracks and computer files (including MP3/ When reading discs recorded using formats other than WMA files).
Page 268
266 UNDERSTANDING YOUR INSTRUMENT PANEL When using the MP3/WMA encoder to compress audio Sampling Fre- Bit Rate (kbps) data to an MP3/WMA file, the bit rate and sampling Specification quency (kHz) frequencies in the following table are supported. In 48, 64, 96, 128, 44.1 and 48 addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Loading times for playback of MP3/WMA files may be begin playing the files contained in that folder (or the affected by the following: next folder in sequence if the selection does not contain playable files). •...
Page 270
268 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode EJECT Button (Auxiliary Mode) The auxiliary (AUX) jack is an audio input jack which No function. allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Operating Instructions - Uconnect™ Phone intended for home and other limited viewing uses only, (If Equipped) unless otherwise authorized by Macrovision. Reverse Refer to “Uconnect™ Phone” in the Uconnect™ User engineering or disassembly is prohibited. Manual located on the DVD for further details.
Page 272
270 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To access the ESN/SID, refer to the following steps: Sirius Satellite Radio service is pre-activated, and you ESN/SID Access may begin listening immediately to the one year of audio With the ignition switch in the ON/RUN or ACC posi- service that is included with the factory-installed satellite tion and the radio on, press the SETUP button and scroll radio system in your vehicle.
Page 273
UNDERSTANDING YOUR INSTRUMENT PANEL 271 bikes should be placed as far rearward as possible, within Operating Instructions - Uconnect™ Multimedia the loading design of the rack. Do not place items directly (Satellite) Mode on or above the antenna. NOTE: The ignition switch must be in the ON/RUN or Reception Quality ACC position to operate the radio.
Page 274
272 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button MUSIC TYPE Button Pressing the INFO button will cycle the display informa- Pressing this button once will turn on the Music Type tion between Artist, Song Title, and Composer (if avail- mode for five seconds. Pressing the MUSIC TYPE button able).
UNDERSTANDING YOUR INSTRUMENT PANEL 273 SETUP Button the SET button twice and SET 2 will show in the display Pressing the SETUP button allows you to select the window. Each button can be set for SET 1 and SET 2. This following items: allows a total of 12 Satellite channels to be stored into pushbutton memory.
274 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions (Voice Command System) — If Equipped Refer to “Voice Command” in the Uconnect™ User Manual located on the DVD for further details. Operating Instructions (Uconnect™ Phone) — If Equipped Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.
Page 277
UNDERSTANDING YOUR INSTRUMENT PANEL 275 Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio. Push the ON/VOLUME control knob a second and radio frequency. time to turn off the radio.
Page 278
276 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Push the rotary TUNE/SCROLL control knob a third Pressing the RW (Rewind) or FF (Fast Forward) buttons time and TREBLE will display. Turn the TUNE/SCROLL causes the tuner to search for the next frequency in the control knob to the right or left to increase or decrease the direction of the arrows.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 SET/RND Button — To Set the Pushbutton Memory Buttons 1 - 6 When you are receiving a station that you wish to These buttons tune the radio to the stations that you commit to pushbutton memory, press the SET/RND commit to pushbutton memory (12 AM and 12 FM button.
Page 280
278 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting Compact Disc(s) CAUTION! (Continued) Gently insert one CD into the CD player with the CD • Do not use adhesive labels. These labels can peel label facing up. The CD will automatically be pulled into away and jam the player mechanism.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 SEEK Button SET/RND Button (Random Play Button) Press the right SEEK button for the next selection on the Press this button while the CD is playing to activate CD. Press the left SEEK button to return to the beginning Random Play.
Page 282
280 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 • Level 1: 12 (including a separator . and a three- Level 1 and Level 2 and includes the Joliet extension. character extension) When reading discs recorded using formats other than •...
Page 283
UNDERSTANDING YOUR INSTRUMENT PANEL 281 extension may cause playback problems. The radio is ID3 Tag information for artist, song title, and album title designed to recognize the file as an invalid MP3 and will are supported for version 1 ID3 tags. ID3 version 2 is not not play the file.
282 UNDERSTANDING YOUR INSTRUMENT PANEL • Number of files and folders - Loading times will Pressing the DISC/AUX button will change the mode to increase with more files and folders auxiliary device if the AUX jack is connected. To increase the speed of disc loading, it is recommended NOTE: The AUX device must be turned on and the to use CD-R media and single-session discs.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
Page 286
284 UNDERSTANDING YOUR INSTRUMENT PANEL Voice Command System (Radio) — If Equipped If your vehicle is not equipped with or this feature is not Refer to “Voice Command” in “Understanding The Fea- available on your vehicle, a “Not Equipped With tures Of Your Vehicle”.
Page 287
UNDERSTANDING YOUR INSTRUMENT PANEL 285 4. Adjust the minutes using the right side TUNE/ RW/FF SCROLL control knob. Press the TUNE/SCROLL control Pressing the RW (Rewind) or FF (Fast Forward) buttons knob to save time change. causes the tuner to search for the next frequency in the direction of the arrows.
Page 288
286 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a third or turning the TUNE/SCROLL control knob within five time and TREBLE will display. Turn the TUNE/SCROLL seconds will allow the program format type to be se- control knob to the right or left to increase or decrease the lected.
Page 289
UNDERSTANDING YOUR INSTRUMENT PANEL 287 By pressing the SEEK button when the Music Type icon Program Type 16-Digit Character Display is displayed, the radio will be tuned to the next frequency News News station with the same selected Music Type name. The Nostalgia Nostalga Music Type function only operates when in the FM...
Page 290
288 UNDERSTANDING YOUR INSTRUMENT PANEL the minutes using the right side TUNE/SCROLL You may add a second station to each pushbutton by control knob. Press the TUNE/SCROLL control knob repeating the above procedure with this exception: Press to save time change. the SET/RND button twice and SET 2 will show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 Operation Instructions — CD MODE for CD and If you insert a disc with the ignition ON and the radio MP3 Audio Play ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and •...
Page 292
290 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within RW/FF 10 seconds, it will be reloaded. If the CD is not removed, Press and hold FF (Fast Forward) and the CD player will the radio will reinsert the CD but will not play it.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 • Maximum number of files: 255 Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 • Maximum number of folders. (The radio display of file file recording media and formats are limited. When names and folder names is limited.
Page 294
292 UNDERSTANDING YOUR INSTRUMENT PANEL Discs created with an option such as keep disc open after MPEG Sampling Fre- Bit Rate (kbps) writing are most likely multisession discs. The use of Specification quency (kHz) multisession for CD audio or MP3 playback may result in 320, 256, 224, longer disc loading times.
UNDERSTANDING YOUR INSTRUMENT PANEL 293 Playback of MP3 Files LIST Button (CD Mode for MP3 Play) When a medium containing MP3 data is loaded, the Pressing the LIST button will bring up a list of all folders radio checks all files on the medium. If the medium on the disc.
294 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds TIME Button (Auxiliary Mode) to return to elapsed time display. Press this button to change the display to time of day. The time of day will display for five seconds (when the Operation Instructions - Auxiliary Mode ignition is OFF).
Page 297
UNDERSTANDING YOUR INSTRUMENT PANEL 295 radio system in your vehicle. Sirius will supply a wel- using the TUNE/SCROLL control knob until Sirius ID is come kit that contains general information, including selected. Press the TUNE/SCROLL control knob and the how to setup your on-line listening account. For further Sirius ID number will display.
Page 298
296 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down.
Page 299
UNDERSTANDING YOUR INSTRUMENT PANEL 297 additional three seconds will make the radio display the Toggle the MUSIC TYPE button again to select the music Song Title all of the time (press and hold again to return type. to normal display). By pressing the SEEK button when the Music Type RW/FF function is active, the radio will be tuned to the next...
298 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory Every time a preset button is used, a corresponding When you are receiving a channel that you wish to button number will display. commit to pushbutton memory, press the SET button. Buttons 1 - 6 The symbol SET 1 will now show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 Pressing the center button will make the radio switch between the various modes available (AM/FM/SAT/ CD/HDD/AUX/VES, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in.
300 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player CD/DVD DISC MAINTENANCE Pressing the top of the switch once will go to the next To keep a CD/DVD in good condition, take the following track on the CD. Pressing the bottom of the switch once precautions: will go to the beginning of the current track, or to the 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 NOTE: If you experience difficulty in playing a particu- Manual Heating And Air Conditioning lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service.
Page 304
302 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control NOTE: If your air conditioning performance seems Rotate this control to regulate the lower than expected, check the front of the A/C con- amount of air forced through the ven- denser located in front of the radiator for an accumula- tilation system in any mode.
Page 305
UNDERSTANDING YOUR INSTRUMENT PANEL 303 Panel Floor Air is directed through the outlets in the instrument Air is directed through the floor outlets with a panel. These outlets can be adjusted to direct airflow. small amount flowing through the defrost and side window demist outlets.
Page 306
304 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: NOTE: • The air conditioning compressor operates in Mix, • Continuous use of the Recirculation mode may make Defrost, or a blend of these modes, even if the Air the inside air stuffy and window fogging may occur. Conditioning (A/C) button is not pressed.
UNDERSTANDING YOUR INSTRUMENT PANEL 305 Air Conditioning Control Automatic Temperature Control (ATC) — If Press this button to engage the Air Equipped Conditioning. A light will illuminate when the Air Conditioning system is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer tem-...
Page 308
306 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the system is quite simple. You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting 1. Turn the Mode Control knob (on the right) and the the “O” (OFF) position on the blower control stops the Blower Control knob (on the left) to AUTO.
Page 309
UNDERSTANDING YOUR INSTRUMENT PANEL 307 • If your air conditioning performance seems lower than Manual Operation expected, check the front of the A/C condenser located This system offers a full complement of manual override in front of the radiator for an accumulation of dirt or features, which consist of Blower Preferred Automatic, insects.
Page 310
308 UNDERSTANDING YOUR INSTRUMENT PANEL...
Page 311
UNDERSTANDING YOUR INSTRUMENT PANEL 309 • Floor The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets.
Page 312
310 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control NOTE: • When the ignition switch is turned to the LOCK Press this button to turn on the air conditioning during manual operation position, the recirculation feature will be cancelled. only. When the air conditioning is •...
UNDERSTANDING YOUR INSTRUMENT PANEL 311 • Most of the time, when in Automatic Operation, you Summer Operation can temporarily put the system into Recirculation The engine cooling system in air-conditioned vehicles Mode by pressing the Recirculation button. However, must be protected with a high-quality antifreeze coolant under certain conditions, while in Automatic Mode, to provide proper corrosion protection and to protect the system is blowing air out the defrost vents.
Page 314
312 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 315
UNDERSTANDING YOUR INSTRUMENT PANEL 313 Control Setting Suggestions for Various Weather Conditions...
STARTING AND OPERATING 319 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both Never leave children alone in a vehicle. Leaving inside and outside mirrors, and fasten your seat belts. children in a vehicle unattended is dangerous for a number of reasons.
320 STARTING AND OPERATING Turn the ignition switch to the START position and If Engine Fails To Start release when the engine starts. If the engine fails to start WARNING! within 10 seconds, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the “Normal •...
STARTING AND OPERATING 321 With Tip Start ENGINE BLOCK HEATER — IF EQUIPPED If the engine fails to start after you have followed the The engine block heater warms the engine, and permits “Normal Starting” or “Extreme Cold Weather” proce- quicker starts in cold weather.
322 STARTING AND OPERATING AUTOMATIC TRANSMISSION WARNING! • Unintended movement of a vehicle could injure CAUTION! those in or near the vehicle. As with all vehicles, Damage to the transmission may occur if the follow- you should never exit a vehicle while the engine is ing precautions are not observed: running.
STARTING AND OPERATING 323 Key Ignition Park Interlock WARNING! (Continued) This vehicle is equipped with a Key Ignition Park Inter- • Never leave children alone in a vehicle, or with lock which requires the shift lever to be placed in PARK access to an unlocked vehicle.
324 STARTING AND OPERATING Four–Speed Automatic Transmission The shift lever position display (located in the instrument panel cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of the PARK position (refer to “Brake/Transmission Shift Interlock System”...
Page 327
STARTING AND OPERATING 325 PARK WARNING! This range supplements the parking brake by locking the • Never use the PARK position as a substitute for transmission. The engine can be started in this range. Never attempt to use PARK while vehicle is in motion. the parking brake.
Page 328
326 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • It is dangerous to move the shift lever out of PARK • Unintended movement of a vehicle could injure or NEUTRAL if the engine speed is higher than those in or near the vehicle. As with all vehicles, idle speed.
Page 329
STARTING AND OPERATING 327 WARNING! (Continued) CAUTION! (Continued) • Never leave children alone in a vehicle, or with • DO NOT race the engine when shifting from access to an unlocked vehicle. Allowing children PARK or NEUTRAL into another gear range, as to be in a vehicle unattended is dangerous for a this can damage the drivetrain.
Page 330
328 STARTING AND OPERATING REVERSE CAUTION! This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete Towing the vehicle, coasting, or driving for any other stop. reason with the transmission in NEUTRAL can result in severe transmission damage.
Page 331
STARTING AND OPERATING 329 When frequent transmission shifting occurs (such as During cold temperatures, transmission operation may when operating the vehicle under heavy loading condi- be modified depending on engine and transmission tions, in hilly terrain, traveling into strong head winds, or temperature as well as vehicle speed.
Page 332
330 STARTING AND OPERATING 1 (First) In the event of a momentary problem, the transmission This range is used for hard pulling at low speeds in mud, can be reset to regain all forward gears by performing the sand, snow, or on steep grades. Begins and stays in low following steps: gear with no upshift.
Page 333
STARTING AND OPERATING 331 • vehicle speed is sufficiently high, If the transmission cannot be reset, authorized dealer service is required. • the driver is not heavily pressing the accelerator, and Overdrive Operation • the TOW/HAUL button has not been activated. The automatic transmission includes an electronically controlled Overdrive (fourth gear).
Page 334
332 STARTING AND OPERATING NOTE: TOW/HAUL mode locks out Overdrive. Torque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly different feeling or response during normal operation in the upper gears.
STARTING AND OPERATING 333 FOUR-WHEEL DRIVE OPERATION position locks the front driveshaft and rear driveshaft together and forces the front and rear wheels to rotate at Command-Trac II Transfer Case – If Equipped the same speed. Operating Information And Precautions Use the transfer case NEUTRAL position for recreational The Command-Trac II transfer case provides four posi- towing only.
Page 336
334 STARTING AND OPERATING CAUTION! (Continued) WARNING! • The 4WD LOCK position and 4WD LOW position • You or others could be injured if you leave the are intended for loose or slippery road surfaces vehicle unattended with the transfer case in the only.
Page 337
STARTING AND OPERATING 335 WARNING! (Continued) • Since four-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road con- ditions permit. You or others could be injured. Shift Positions The transfer case switch is located on the center console next to the shift lever.
Page 338
336 STARTING AND OPERATING 4WD Lock Transfer Case Position Indicator Lights Four-Wheel Drive High Range - This range locks the front The four-wheel drive indicator lights (4WD and 4 LOW) driveshaft and rear driveshaft together forcing the front are located in the instrument cluster. The NEUTRAL and rear wheels to rotate at the same speed.
Page 339
STARTING AND OPERATING 337 Shifting Procedures engine either OFF or RUNNING. This shift cannot be completed if the ignition switch is in the ACC position. NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case NOTE: The four-wheel drive system will not allow will not shift, the indicator light for the previous position shifts between 2WD and 4WD LOCK if the rear wheels...
Page 340
338 STARTING AND OPERATING Shifting can be performed with the vehicle rolling 2 to 3. Move the transfer case switch to the desired position. 3 mph (3 to 5 km/h) using the “Preferred Procedure” or 4. After the desired position indicator light is on (not completely stopped using the “Alternate Procedure.”...
STARTING AND OPERATING 339 Selec-Trac II Transfer Case – If Equipped For added capability when traversing steep grades, rough terrain, or extremely poor traction surfaces, select Operating Information And Precautions the transfer case 4WD LOW position. This position locks The Selec-Trac II active on-demand transfer case pro- the front driveshaft and rear driveshaft together and vides four positions: forces the front and rear wheels to rotate at the same...
Page 342
340 STARTING AND OPERATING CAUTION! (Continued) WARNING! • When operating your vehicle in 4WD LOW, the • You or others could be injured if you leave the engine speed is approximately three times that of vehicle unattended with the transfer case in the the 2WD position or 4WD AUTO position at a NEUTRAL position without first fully engaging given road speed.
Page 343
STARTING AND OPERATING 341 WARNING! (Continued) • Since four-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road con- ditions permit. You or others could be injured. Shift Positions The transfer case switch is located on the center console next to the shift lever.
Page 344
342 STARTING AND OPERATING 4WD Auto Four-Wheel Drive Auto High Range – This active on- Neutral - This range disengages both the front driveshaft demand range makes available optimum traction for a and rear driveshaft from the powertrain. To be used for wide range of conditions, while maximizing driver con- flat towing behind another vehicle.
Page 345
STARTING AND OPERATING 343 NOTE: The “SERV 4WD Warning Light” monitors the vehicle stopped or in motion. If the vehicle is stopped, electric shift four-wheel drive system. If this light re- the ignition switch must be in the ON position with the mains on after engine start up, or it illuminates during engine either OFF or RUNNING.
344 STARTING AND OPERATING 3. While still rolling, move the transfer case switch to the process, then the indicator light will flash, and the desired position. current transfer case position will be maintained. To retry a shift, move the transfer case switch back to the original 4.
STARTING AND OPERATING 345 They are not designed for cornering at the same speeds as CAUTION! conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfacto- Do not use 4WD LOW range when operating the rily in off-road conditions.
346 STARTING AND OPERATING Driving through water more than a few inches/ Standing Water centimeters deep will require extra caution to ensure Avoid driving in standing water deeper than 20 in safety and prevent damage to your vehicle. If you must (51 cm), and reduce speed appropriately to minimize drive through water, try to determine the depth and the wave effects.
STARTING AND OPERATING 347 lower gear than necessary to maintain headway. Over- speed. If the brakes are required to control vehicle speed, revving the engine can spin the wheels and traction will apply them lightly and avoid locking or skidding the be lost.
348 STARTING AND OPERATING turning the front wheels slowly left and right. This may always a good idea to check for damage. That way you provide a fresh “bite” into the surface and will usually can get any problems taken care of right away and have provide traction to complete the climb.
STARTING AND OPERATING 349 • After extended operation in mud, sand, water, or POWER STEERING similar dirty conditions, have the radiator, fan, brake The standard power steering system will give you good rotors, wheels, brake linings, and axle yokes inspected vehicle response and increased ease of maneuverability and cleaned as soon as possible.
350 STARTING AND OPERATING system. This noise should be considered normal, and it checked if a leak is suspected, abnormal noises are does not in any way damage the steering system. apparent, and/or the system is not functioning as antici- pated.
STARTING AND OPERATING 351 If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied.
Page 354
352 STARTING AND OPERATING NOTE: WARNING! • When the parking brake is applied and the transmis- • Never use the PARK position as a substitute for sion is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound the parking brake.
STARTING AND OPERATING 353 ANTI-LOCK BRAKE SYSTEM WARNING! (Continued) The Anti-Lock Brake System (ABS) is designed to aid the • Be sure the parking brake is fully disengaged driver in maintaining vehicle control under adverse before driving; failure to do so can lead to brake braking conditions.
Page 356
354 STARTING AND OPERATING The ABS conducts a low-speed self-test at about 12 mph WARNING! (Continued) (20 km/h). If you have your foot lightly on the brake • The ABS cannot prevent the natural laws of phys- while this test is occurring, you may feel slight pedal ics from acting on the vehicle, nor can it increase movement.
STARTING AND OPERATING 355 • Engines may idle at higher speeds during warm-up, CAUTION! which could cause rear wheels to spin and result in loss of vehicle control. Be especially careful while The ABS is subject to possible detrimental effects of driving on slippery roads, in close-quarter maneuver- electronic interference caused by improperly in- ing, parking, or stopping.
356 STARTING AND OPERATING system includes Anti-Lock Brake System (ABS), Traction WARNING! Control System (TCS), Brake Assist System (BAS), Hill Start Assist (HSA), Electronic Roll Mitigation (ERM), and The Anti-Lock Brake System (ABS) cannot prevent Electronic Stability Control (ESC). These systems work the natural laws of physics from acting on the ve- together to enhance both vehicle stability and control in hicle, nor can it increase the traction afforded by...
STARTING AND OPERATING 357 a limited slip differential and controls the wheel spin benefit of the system, you must apply continuous brak- across a driven axle. If one wheel on a driven axle is ing pressure during the stopping sequence, (do not spinning faster than the other, the system will apply the “pump”...
358 STARTING AND OPERATING Electronic Roll Mitigation (ERM) WARNING! This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the Many factors, such as vehicle loading, road condi- speed of the vehicle. When ERM determines that the rate tions, and driving conditions, influence the chance of change of the steering wheel angle and vehicle’s speed that wheel lift or rollover may occur.
Page 361
STARTING AND OPERATING 359 time expires, the system will release brake pressure and WARNING! the vehicle will roll down the hill as normal. The system will release brake pressure in proportion to amount of There may be situations where the Hill Start Assist throttle applied.
Page 362
360 STARTING AND OPERATING Disabling And Enabling HSA WARNING! This feature can be turned on or turned off. To change the • If you use a trailer brake controller with your current setting, proceed as follows: trailer, the trailer brakes may be activated and For vehicles equipped with the Electronic Vehicle Infor- deactivated with the brake switch.
STARTING AND OPERATING 361 3. Apply the parking brake. Hill Descent Control (HDC) – If Equipped HDC is only intended for low speed off-road driving. 4. Start the engine. HDC maintains vehicle speed while descending hills in 5. Rotate the steering wheel one-half turn to the left. off-road driving conditions by applying the brakes when necessary.
Page 364
362 STARTING AND OPERATING HDC control speed. If more speed is desired during HDC The “Hill Descent” button is located in the lower switch control, the accelerator pedal will increase vehicle speed bank below the climate control. in the usual manner. When either the brake or the accelerator is released, HDC will control the vehicle at the original set speed.
STARTING AND OPERATING 363 2. Press the “Hill Descent” button. The “Hill Descent counteracting the oversteer or understeer condition. En- Control Indicator Light” in the instrument cluster will gine power may also be reduced to help the vehicle turn on solid. maintain the desired path.
Page 366
364 STARTING AND OPERATING Light” also flashes when the TCS is active. If the “ESC ESC Operating Modes Activation/Malfunction Indicator Light” begins to flash Depending upon model and mode of operation, the ESC during acceleration, ease up on the accelerator and apply system has up to three operating modes: “ESC On”...
Page 367
STARTING AND OPERATING 365 Partial Off – Two-Wheel Drive Vehicles And “Partial Off” mode by momentarily pressing the “ESC Four-Wheel Drive Vehicles In 2WD And 4WD High Off” button. Once the situation requiring “Partial Off” Range mode is overcome, turn ESC back on by momentarily The “Partial Off”...
366 STARTING AND OPERATING In this mode, ESC and TCS are turned off (except for the to the PARK position and then moved out of the PARK “limited slip” feature described in the TCS section) until position. This will occur even if the message was the vehicle reaches a speed of 40 mph (64 km/k).
Page 369
STARTING AND OPERATING 367 Light” comes on continuously with the engine running, a NOTE: • The “ESC Activation/Malfunction Indicator Light” malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the and the “ESC OFF Indicator Light” come on momen- vehicle has been driven several miles (kilometers) at tarily each time the ignition switch is turned ON.
368 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 371
STARTING AND OPERATING 369 • High flotation tire sizing is based on U.S. design compact spare tires have the letter “T” or “S” molded into the sidewall preceding the size designation. Ex- standards and it begins with the tire diameter molded ample: T145/80D18 103M.
Page 372
370 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
STARTING AND OPERATING 371 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
372 STARTING AND OPERATING Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the Cold Tire Inflation Pressure vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
STARTING AND OPERATING 373 Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
Page 376
374 STARTING AND OPERATING axles must not be exceeded. For further information on This placard tells you important information about GAWRs, vehicle loading, and trailer towing, refer to the: “Vehicle Loading” in this section. 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of...
Page 377
STARTING AND OPERATING 375 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcu- sengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity.
STARTING AND OPERATING 377 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
378 STARTING AND OPERATING stability of the vehicle and can produce a feeling of WARNING! (Continued) sluggish response or over responsiveness in the steering. • Unequal tire pressures from one side of the ve- Unequal tire pressures can cause erratic and unpredict- hicle to the other can cause the vehicle to drift to able steering response.
Page 381
STARTING AND OPERATING 379 Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the winter.
380 STARTING AND OPERATING Tire Pressures For High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
STARTING AND OPERATING 381 vehicle. If your vehicle has this option refer to an Compact Spare Tire – If Equipped authorized tire dealer for the recommended tire rotation The compact spare is for temporary emergency use only. pattern. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on If your vehicle is not equipped with an original equip- the Tire and Loading Information Placard located on the...
382 STARTING AND OPERATING your original equipment tire, replace (or repair) the WARNING! original equipment tire and reinstall on the vehicle at the first opportunity. Compact spares are for temporary emergency use only. With these spares, do not drive more than Limited-Use Spare –...
STARTING AND OPERATING 383 Tire Spinning WARNING! When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h). Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle WARNING! handling.
384 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm).
STARTING AND OPERATING 385 • Distance driven when replacement is needed. (Refer to the paragraph on “Tread Wear Indicators”). Refer to the “Tire and Loading WARNING! Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be Tires and the spare tire should be replaced after six found on the original equipment tire sidewall.
386 STARTING AND OPERATING WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 389
STARTING AND OPERATING 387 CAUTION! CAUTION! (Continued) • Install chains on the rear wheels as tightly as To avoid damage to your vehicle, tires, or chains, possible and then retighten after driving about ⁄ observe the following precautions: mile (0.8 km). •...
388 STARTING AND OPERATING These cautions apply to all chain traction devices, includ- The suggested rotation method is the “forward-cross” ing link and cable (radial) chains. shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be TIRE ROTATION RECOMMENDATIONS reversed.
STARTING AND OPERATING 389 three hour period. The cold tire inflation pressure must CAUTION! not exceed the maximum inflation pressure molded into the tire sidewall. Refer to “Tires – General Information” Proper operation of four-wheel drive vehicles de- in “Starting and Operating” for information on how to pends on tires of equal size, type and circumference properly inflate the vehicle’s tires.
Page 392
390 STARTING AND OPERATING cold placard pressure in order for the “Tire Pressure Telltale Light” will turn off only after the tires are inflated Monitoring Telltale Light” to turn off. The system will to the vehicle’s recommended cold placard pressure automatically update and the “Tire Pressure Monitoring value.
STARTING AND OPERATING 391 • The TPMS is not a substitute for proper tire mainte- CAUTION! (Continued) nance, and it is the driver’s responsibility to maintain • After inspecting or adjusting the tire pressure, correct tire pressure using an accurate tire pressure always reinstall the valve stem cap.
Page 394
392 STARTING AND OPERATING The TPMS consists of the following components: Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will • Receiver Module illuminate in the instrument cluster, a “LOW TIRE • Four Tire Pressure Monitoring Sensors PRESSURE”...
Page 395
STARTING AND OPERATING 393 Service TPMS Warning Vehicles With Full-Size Spare When a system fault is detected, the “Tire Pressure 1. The matching full-size spare wheel and tire assembly Monitoring Telltale Light” will flash on and off for has a tire pressure monitoring sensor that can be moni- 75 seconds and then remain on solid.
394 STARTING AND OPERATING 2. If you install the compact spare tire in place of a road active road tires. The vehicle may need to be driven for tire that has a pressure below the low-pressure warning up to 20 minutes above 15 mph (24 km/h) in order for the limit, a chime will sound and the “TPMS Telltale Light”...
Page 397
STARTING AND OPERATING 395 • Three Trigger Modules (mounted in three of the four will sound when tire pressure is low in one or more of the wheel-wells) four active road tires. In addition, the Electronic Vehicle Information Center (EVIC) will display a “LOW TIRE •...
Page 398
396 STARTING AND OPERATING Should this occur, you should stop as soon as possible seconds and then display dashes (- -) in place of the and inflate the tires with low pressure (those flashing in pressure value to indicate which sensor is not being the EVIC graphic) to the vehicle’s recommended cold received.
Page 399
STARTING AND OPERATING 397 If the ignition key is cycled, this sequence will repeat, Vehicles With Full-Size Spare providing the system fault still exists. If the system fault 1. The matching full size spare wheel and tire assembly no longer exists, the “Tire Pressure Monitoring Telltale has a tire pressure monitoring sensor that can be moni- Light”...
Page 400
398 STARTING AND OPERATING Vehicles With Compact Spare 4. For each subsequent ignition key cycle, a chime will sound, the “TPMS Telltale Light” will flash on and off for 1. The compact spare tire does not have a tire pressure 75 seconds and then remain on solid, and the EVIC will monitoring sensor.
STARTING AND OPERATING 399 General Information FUEL REQUIREMENTS This device complies with Part 15 of the FCC rules and All engines are designed to meet all emis- RSS 210 of Industry Canada. Operation is subject to the sions regulations and provide excellent following conditions: fuel economy and performance when us- ing high quality unleaded “regular”...
400 STARTING AND OPERATING Over 40 auto manufacturers worldwide have issued and Gasoline/Oxygenate Blends endorsed consistent gasoline specifications (the World- Some fuel suppliers blend unleaded gasoline with oxy- wide Fuel Charter, WWFC) which define fuel properties genates such as Ethanol. Fuels blended with oxygenates necessary to deliver enhanced emissions, performance, may be used in your vehicle.
STARTING AND OPERATING 401 E-85 Usage In Non-Flex Fuel Vehicles To fix a Non-FFV vehicle inadvertently fueled once with Non-FFV vehicles are compatible with gasoline contain- E-85 perform the following: ing 10% ethanol (E10). Gasoline with higher ethanol • drain the fuel tank (see your authorized dealer) content may void the vehicle’s warranty.
402 STARTING AND OPERATING of gasoline may not be indicated on the gasoline pump; Fuel System Cautions therefore, you should ask your gasoline retailer whether CAUTION! the gasoline contains MMT. It is even more important to look for gasolines without MMT in Canada, because Use the following guidelines to maintain your vehi- MMT can be used at levels higher than those allowed in cle’s performance:...
STARTING AND OPERATING 403 Carbon Monoxide Warnings CAUTION! (Continued) • The use of fuel additives, which are now being WARNING! sold as octane enhancers, is not recommended. Carbon monoxide (CO) in exhaust gases is deadly. Most of these products contain high concentra- Follow the precautions below to prevent carbon tions of methanol.
404 STARTING AND OPERATING ADDING FUEL WARNING! (Continued) Fuel Filler Cap (Gas Cap) • Guard against carbon monoxide with proper The gas cap is located behind the fuel filler door, on the maintenance. Have the exhaust system inspected driver’s side of the vehicle. If the gas cap is lost or every time the vehicle is raised.
Page 407
STARTING AND OPERATING 405 CAUTION! WARNING! • Damage to the fuel system or emission control • Never have any smoking materials lit in or near system could result from using an improper fuel the vehicle when the gas cap is removed or the cap (gas cap).
406 STARTING AND OPERATING • If the gas cap is not tightened properly, the MIL will VEHICLE LOADING come on. Be sure the gas cap is tightened every time Certification Label the vehicle is refueled. As required by National Highway Traffic Safety Admin- Loose Fuel Filler Cap Message istration regulations, your vehicle has a certification label If the vehicle diagnostic system determines that the fuel...
Page 409
STARTING AND OPERATING 407 Gross Vehicle Weight Rating (GVWR) springs, tires, or wheels). Heavier axles or suspension The GVWR is the total permissible weight of your vehicle components, sometimes specified by purchasers for in- including driver, passengers, vehicle, options, trailer creased durability, does not necessarily increase the ve- tongue weight, and cargo.
Page 410
408 STARTING AND OPERATING capacity conditions, and with no occupants or cargo until the specified weight limitations are met. Store the loaded into the vehicle. The front and rear curb weight heavier items down low and be sure that the weight is values are determined by weighing your vehicle on a distributed equally.
STARTING AND OPERATING 409 TRAILER TOWING exceed the GVWR. Refer to “Vehicle Loading/Vehicle In this section, you will find safety tips and information Certification Label” in “Starting and Operating” for on limits to the type of towing you can reasonably do further information.
Page 412
410 STARTING AND OPERATING rear GAWR. Refer to “Vehicle Loading/Vehicle Certifica- WARNING! tion Label” in “Starting and Operating” for further information. If the Gross Trailer Weight (GTW) is 3,500 lbs (1 587 kg) or more, it is mandatory to use a weight- WARNING! distributing hitch to ensure stable handling of your vehicle.
Page 413
STARTING AND OPERATING 411 Trailer Sway Control – Mechanical Weight-Distributing Hitch The trailer sway control is a telescoping link that can be A weight-distributing system works by applying lever- installed between the hitch receiver and the trailer tongue age through spring (load) bars. They are typically used that typically provides adjustable friction associated with for heavier loads, to distribute trailer tongue weight to the telescoping motion to dampen any unwanted trailer...
Page 414
412 STARTING AND OPERATING WARNING! • An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, brak- ing performance, and could result in a collision. • Weight Distributing Systems may not be compat- ible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Rec- reational Vehicle...
Page 415
STARTING AND OPERATING 413 With Weight Distributing Hitch (Correct) Improper Adjustment of Weight-Distributing Hitch (Incorrect)
414 STARTING AND OPERATING Trailer Hitch Classification Trailer Hitch Classification Definitions Your vehicle is capable of towing trailers up to 2,000 lbs Class Max. Trailer Hitch Industry (907 kg) without added equipment or alterations to the Standards standard equipment. Your vehicle may be factory Class I - Light Duty 2,000 lbs (907 kg) equipped for safe towing of trailers weighing over...
STARTING AND OPERATING 415 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Model Frontal Area Max. GTW Max. Tongue Wt. Transmission (Gross Trailer Wt.) (See Note) 3.7L/Automatic 32 sq ft (2.97 sq m) 2,000 lbs (907 kg)
Page 418
416 STARTING AND OPERATING When Towing Trailers With Gross Trailer Weight (GTW) Between 3,500 Lbs (1 588 kg) And 5,000 Lbs (2 268 kg) The following chart provides maximum trailer weight ratings towable for the following engine/transmission combinations, ONLY if using a weight distributing hitch. Engine/ Model Frontal Area...
STARTING AND OPERATING 417 Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
418 STARTING AND OPERATING NOTE: Remember that everything put into or on the CAUTION! (Continued) trailer adds to the load on your vehicle. Also, additional • Then, during the first 500 miles (805 km) that a factory-installed options, or authorized dealer-installed trailer is towed, do not drive over 50 mph options, must be considered as part of the total load on (80 km/h) and do not make starts at full throttle.
Page 421
STARTING AND OPERATING 419 WARNING! (Continued) WARNING! (Continued) • Make certain that the load is secured in the trailer • Vehicles with trailers should not be parked on a and that is will not shift during travel. When grade. When parking, apply the parking brake on trailering cargo that is not fully secured, dynamic the tow vehicle.
Page 422
420 STARTING AND OPERATING Towing Requirements – Tires on replacement tires and for the proper tire replace- ment procedures. Replacing tires with a higher load − Do not attempt to tow a trailer while using a compact carrying capacity will not increase the vehicle’s GVWR spare tire.
Page 423
STARTING AND OPERATING 421 CAUTION! WARNING! (Continued) • Towing any trailer will increase your stopping If the trailer weighs more than 1,000 lbs (454 kg) distance. When towing you should allow for addi- loaded, it should have its own brakes, and they tional space between your vehicle and the vehicle should be of adequate capacity.
Page 424
422 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Seven-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 —...
STARTING AND OPERATING 423 Towing Tips specified for “police, taxi, fleet, or frequent trailer tow- Before setting out on a trip, practice turning, stopping, ing.” Refer to “Maintenance Schedule” for the proper and backing the trailer in an area located away from maintenance intervals.
424 STARTING AND OPERATING Cooling System − Highway Driving To reduce potential for engine and transmission over- Reduce speed. heating, take the following actions: − Air Conditioning − City Driving Turn off temporarily. When stopped for short periods of time, shift the trans- mission into NEUTRAL and increase engine idle speed.
STARTING AND OPERATING 425 Recreational Towing — Two-Wheel Drive Models Flat towing (with all four wheels on the ground) is Recreational towing is allowed ONLY if the rear wheels allowed ONLY if the driveshaft is removed. Towing are OFF the ground. This may be accomplished using a with the rear wheels on the ground while the driveshaft tow dolly or vehicle trailer.
426 STARTING AND OPERATING CAUTION! CAUTION! • Front or rear wheel lifts should not be used. Towing with the rear wheels on the ground (while the driveshaft is connected) will cause severe trans- Internal damage to the transmission or transfer mission damage.
Page 429
STARTING AND OPERATING 427 Use the following procedure to prepare your vehicle for CAUTION! (Continued) recreational towing. • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be CAUTION! damaged. It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL (N) before Shifting Into NEUTRAL (N) recreational towing to prevent damage to internal...
Page 430
428 STARTING AND OPERATING 6. Using the point of a ballpoint pen or similar object, 7. After the shift is completed and the NEUTRAL light press and hold the recessed transfer case NEUTRAL (N) comes on, release the NEUTRAL (N) button. button (located above the selector switch) for four sec- 8.
Page 431
STARTING AND OPERATING 429 timer, then the NEUTRAL (N) indicator light will flash CAUTION! continuously until all requirements are met or until the NEUTRAL (N) button is released. Damage to the transmission may occur if the trans- mission is shifted into PARK with the transfer case in •...
Page 432
430 STARTING AND OPERATING 3. Turn the ignition switch to the ON/RUN position, but do not start the engine. 4. Press and hold the brake pedal. 5. Shift the transmission into NEUTRAL. 6. Using the point of a ballpoint pen or similar object, press and hold the recessed transfer case NEUTRAL (N) button (located above the selector switch) for one second.
Page 433
STARTING AND OPERATING 431 NOTE: When shifting out of transfer case NEUTRAL NOTE: • Steps 1 through 5 are requirements that must be met (N), turning the engine OFF may be required to avoid gear clash. prior to pressing the NEUTRAL (N) button, and must continue to be met until the shift has been completed.
434 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the switch bank below the climate controls. potential for overheating your engine by taking the appropriate action.
WHAT TO DO IN EMERGENCIES 435 NOTE: There are steps that you can take to slow down JACKING AND TIRE CHANGING an impending overheat condition: WARNING! • If your air conditioner (A/C) is on, turn it off. The A/C • Do not attempt to change a tire on the side of the system adds heat to the engine cooling system and turning the A/C off can help remove this heat.
436 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
WHAT TO DO IN EMERGENCIES 437 Spare Tire Removal CAUTION! Fit the jack handle extension over the drive nut located in the rear cargo area inside the vehicle. Use the lug wrench The winch mechanism is designed for use with the to rotate the nut counterclockwise until the spare is on jack extension tube only.
438 WHAT TO DO IN EMERGENCIES Preparations For Jacking 4. Place the shift lever into PARK (automatic transmis- sion) or REVERSE (manual transmission). 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery 5.
WHAT TO DO IN EMERGENCIES 439 Jacking Instructions WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a WARNING! jack. Carefully follow these tire changing warnings to • Do not get under the vehicle when it is on a jack. help prevent personal injury or damage to your •...
Page 442
440 WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove spare tire. 2. Remove jack and tools from mounting bracket. As- semble the tools by connecting the driver to the exten- sion, and then to the lug wrench.
Page 443
WHAT TO DO IN EMERGENCIES 441 5. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause a collision.
Page 444
442 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Be sure to mount the spare tire with the valve stem To avoid the risk of forcing the vehicle off the jack, facing outward. The vehicle could be damaged if the do not tighten the wheel nuts fully until the vehicle spare tire is mounted incorrectly.
WHAT TO DO IN EMERGENCIES 443 WARNING! WARNING! A loose tire or jack, thrown forward in a collision or To avoid the risk of forcing the vehicle off the jack, hard stop, could endanger the occupants of the ve- do not tighten the lug nuts fully until the vehicle is hicle.
444 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES WARNING! If your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in Do not attempt jump-starting if the battery is frozen. another vehicle or by using a portable battery booster It could rupture or explode and cause personal injury.
Page 447
WHAT TO DO IN EMERGENCIES 445 WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
446 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park CAUTION! the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 449
WHAT TO DO IN EMERGENCIES 447 8. Disconnect the opposite end of the positive (+) jumper WARNING! cable from the positive (+) post of the booster battery. Do not connect the cable to the negative post (-) of the 9. Disconnect the positive (+) end of the jumper cable discharged battery.
448 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE NOTE: If your vehicle is equipped with Traction Con- If your vehicle becomes stuck in mud, sand or snow, it trol or Electronic Stability Control (ESC), turn the system can often be moved by a rocking motion. Turn your OFF before attempting to “rock”...
WHAT TO DO IN EMERGENCIES 449 SHIFT LEVER OVERRIDE WARNING! If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the Fast spinning tires can be dangerous. Forces gener- following procedure to temporarily move the shift lever: ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires.
450 WHAT TO DO IN EMERGENCIES 4. Press and maintain firm pressure on the brake pedal. 6. Move the shift lever to the NEUTRAL position. 5. Using a screwdriver, reach into the opening and press 7. The vehicle may then be started in NEUTRAL. and hold the shift override lever down.
Page 453
WHAT TO DO IN EMERGENCIES 451 Towing Condition Wheels OFF 2WD Models 4WD Models the Ground See instructions in “Recreational Tow- ing” under “Starting and Operating” If transmission is operable: • Transmission in PARK • Transmission in NEUTRAL Flat Tow NONE •...
452 WHAT TO DO IN EMERGENCIES If the vehicle’s battery is discharged, refer to “Shift Lever Towing Without The Ignition Key Fob Override” in “What To Do In Emergencies” for instruc- Special care must be taken when the vehicle is towed tions on shifting the automatic transmission out of the with the ignition in the LOCK/OFF position.
Page 455
WHAT TO DO IN EMERGENCIES 453 CAUTION! WARNING! Towing faster than 30 mph (48 km/h) or farther than If the driveshaft is removed, the vehicle can roll even 15 miles (24 km) with rear wheels on the ground can if the transmission is in PARK, which could cause cause severe damage to the transmission.
454 WHAT TO DO IN EMERGENCIES Four-Wheel Drive Models CAUTION! The manufacturer recommends towing with all wheels • Front or rear wheel lifts should not be used. OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and Internal damage to the transmission or transfer the opposite end on a towing dolly.
458 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
MAINTAINING YOUR VEHICLE 459 “Electronic Vehicle Information Center (EVIC)” in “Un- For states that require an Inspection and Mainte- derstanding Your Instrument Panel” for further informa- nance (I/M), this check verifies the “Malfunction tion. Tighten the gas cap until a clicking sound is heard. Indicator Light (MIL)”...
Page 462
460 MAINTAINING YOUR VEHICLE 2. If you crank or start the engine, you will have to start If your OBD II system is not ready, you should see your this test over. authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, 3.
MAINTAINING YOUR VEHICLE 461 REPLACEMENT PARTS WARNING! Use of genuine MOPAR parts for normal/scheduled maintenance and repairs is highly recommended to en- You can be badly injured working on or around a sure the designed performance. Damage or failures motor vehicle. Only do service work for which you caused by the use of non-MOPAR parts for maintenance have the knowledge and the proper equipment.
462 MAINTAINING YOUR VEHICLE Engine Oil CAUTION! • Failure to properly maintain your vehicle or per- Checking Oil Level To assure proper engine lubrication, the engine oil must form repairs and service when necessary could be maintained at the correct level. Check the oil level at result in more costly repairs, damage to other regular intervals, such as every fuel stop.
Page 465
MAINTAINING YOUR VEHICLE 463 Engine Oil Selection CAUTION! For best performance and maximum protection under all types of operating conditions, the manufacturer recom- Overfilling or underfilling the crankcase will cause mends engine oils that are API Certified and meet the aeration or loss of oil pressure.
Page 466
464 MAINTAINING YOUR VEHICLE Synthetic Engine Oils CAUTION! You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- Do not use chemical flushes in your engine oil as the mended maintenance intervals for oil and filter changes chemicals can damage your engine.
MAINTAINING YOUR VEHICLE 465 Engine Oil Filter WARNING! The engine oil filter should be replaced with a new filter at every engine oil change. The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine NOTE: For best access to the oil filter, a drive on hoist backfire.
466 MAINTAINING YOUR VEHICLE Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. • Battery gas is flammable and explosive. Keep You will never have to add water, nor is periodic main- flame or sparks away from the battery. Do not use tenance required.
MAINTAINING YOUR VEHICLE 467 Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer at the start of each warm season. This service should battery that the positive cable is attached to the include cleaning of the condenser fins and a performance positive post and the negative cable is attached to...
468 MAINTAINING YOUR VEHICLE Protection Agency and is an ozone-saving product. How- WARNING! ever, the manufacturer recommends that air conditioning • Use only refrigerants and compressor lubricants service be performed by an authorized dealer or other service facilities using recovery and recycling equipment. approved by the manufacturer for your air condi- tioning system.
MAINTAINING YOUR VEHICLE 469 tailgate, sliding doors and hood hinges, should be lubri- Windshield Wiper Blades cated periodically with a lithium based grease, such as Clean the rubber edges of the wiper blades and the MOPAR Spray White Lube or equivalent, to assure windshield periodically with a sponge or soft cloth and a quiet, easy operation and to protect against rust and mild non-abrasive cleaner or use the washer solvent.
470 MAINTAINING YOUR VEHICLE Adding Washer Fluid WARNING! The windshield and rear window washers share the same fluid reservoir. The fluid reservoir is located in the front Commercially available windshield washer solvents of the engine compartment. Be sure to check the fluid are flammable.
Page 473
MAINTAINING YOUR VEHICLE 471 into the passenger compartment. In addition, inspect the CAUTION! exhaust system each time the vehicle is raised for lubri- • The catalytic converter requires the use of un- cation or oil change. Replace as required. leaded fuel only. Leaded gasoline will destroy the WARNING! effectiveness of the catalyst as an emissions con- trol device and may seriously reduce engine per-...
Page 474
472 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
MAINTAINING YOUR VEHICLE 473 Cooling System accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the WARNING! face of the A/C condenser (if equipped) or the back of the radiator core. •...
Page 476
474 MAINTAINING YOUR VEHICLE Cooling System – Drain, Flush, And Refill CAUTION! If the engine coolant (antifreeze) is dirty or contains a • Mixing of engine coolant (antifreeze) other than considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough specified HOAT engine coolant (antifreeze), may rinsing to remove all deposits and chemicals.
Page 477
MAINTAINING YOUR VEHICLE 475 Please review these recommendations for using Hybrid CAUTION! (Continued) Organic Additive Technology (HOAT) engine coolant • This vehicle has not been designed for use with (antifreeze). When adding engine coolant (antifreeze): Propylene Glycol based engine coolant (anti- •...
Page 478
476 MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to main- WARNING! tain the proper level of protection against freezing ac- • The warning words “DO NOT OPEN HOT” on cording to the temperatures occurring in the area where the vehicle is operated.
Page 479
MAINTAINING YOUR VEHICLE 477 Disposal Of Used Engine Coolant The radiator normally remains completely full, so there is Used ethylene glycol based engine coolant (antifreeze) is no need to remove the radiator cap unless checking for a regulated substance requiring proper disposal. Check coolant freeze point or replacing engine coolant (anti- with your local authorities to determine the disposal freeze).
478 MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be bottle hoses are not kinked or obstructed. safely driven. The vapor will soon dissipate. •...
Page 481
MAINTAINING YOUR VEHICLE 479 should be checked when pads are replaced. However, WARNING! low fluid level may be caused by a leak and a checkup may be needed. Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or Use only manufacturer’s recommended brake fluid.
480 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container.
Page 483
MAINTAINING YOUR VEHICLE 481 CAUTION! CAUTION! Using a transmission fluid other than the manufac- Do not use chemical flushes in your transmission as turer’s recommended fluid may cause deterioration the chemicals can damage your transmission compo- in transmission shift quality and/or torque converter nents.
482 MAINTAINING YOUR VEHICLE Transfer Case CAUTION! Fluid Level Check Using a transmission fluid other than the manufac- The fluid level should be to the bottom edge of the fill turer’s recommended fluid may cause deterioration hole (1) when the vehicle is in a level position. in transmission shift quality and/or torque converter shudder.
MAINTAINING YOUR VEHICLE 483 Adding Fluid Frequency Of Fluid Change Fluid should be added only to fill hole until fluid begins Under normal operating conditions, the fluid installed at to run out of the hole. the factory will give satisfactory lubrication for the life of the vehicle.
484 MAINTAINING YOUR VEHICLE • Rear axle lubricant should be 0.5 in (11 mm) below the Sky Slider™ Top Care bottom edge of the oil fill hole when the vehicle is in a Immediate removal of any contaminant is recommended. level position.
Page 487
MAINTAINING YOUR VEHICLE 485 • Allow the top to dry before opening. Vacuuming the General Cleaning Careful vacuuming of the top before washing is helpful top with a wet/dry shop vacuum will decrease the in removing dust and other foreign particles. tops drying time, ensure removal of all dirt, and delete streaks in the material.
486 MAINTAINING YOUR VEHICLE equivalent to the complete stain, extending 2 in (50 mm) Weather Strip Care beyond the stain. With a soft bristle brush, scrub in all Lubricate the weather strips periodically with MOPAR directions over the stain. Avoid heavy scrubbing. Rinse Weather Strip Lubricant or equivalent, to keep them soft the area with warm water.
Page 489
MAINTAINING YOUR VEHICLE 487 The following maintenance recommendations will enable Washing you to obtain maximum benefit from the corrosion • Wash your vehicle regularly. Always wash your ve- resistance built into your vehicle. hicle in the shade using MOPAR Car Wash or equiva- What Causes Corrosion? lent, or a mild car wash soap, and rinse the panels Corrosion is the result of deterioration or removal of...
Page 490
488 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is • Do not use abrasive or strong cleaning materials considered the responsibility of the owner. such as steel wool or scouring powder, which will •...
Page 491
MAINTAINING YOUR VEHICLE 489 Wheel And Wheel Trim Care Stain Repel Fabric Cleaning Procedure – If Equipped • All wheels and wheel trim, especially aluminum and Stain Repel seats may be cleaned in the following man- chrome plated wheels, should be cleaned regularly ner: with a mild soap and water to prevent corrosion.
Page 492
490 MAINTAINING YOUR VEHICLE Interior Care Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt Instrument Panel Cover can act as an abrasive and damage the leather upholstery The instrument panel cover has a low glare surface, and should be removed promptly with a damp cloth.
Page 493
MAINTAINING YOUR VEHICLE 491 Cleaning Headlights quarter window equipped with the radio antenna. Do Your vehicle has plastic headlights that are lighter and not use scrapers or other sharp instruments, which may less susceptible to stone breakage than glass headlights. scratch the elements.
492 MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye, or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the seat belts need cleaning, use a mild soap solution or lukewarm water.
Page 498
496 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse — 15 Amp Exterior Lighting – — 10 Amp Right Horn (Hi/Low) Blue Right Front Park and Side Marker, Right — 10 Amp Left Horn (Hi/Low) Tail and Running Lights —...
Page 499
MAINTAINING YOUR VEHICLE 497 Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse — 10 Amp Powertrain Control — 10 Amp Park Assist Module – Module If Equipped/Climate Control System Mod- — 10 Amp Occupant Classifica- ule – If Equipped/ tion Module Compass Module –...
498 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini- Description CAUTION! (Continued) Fuse Fuse • When replacing a blown fuse, it is important to — 10 Amp Antilock Brakes/ use only a fuse having the correct amperage rating. Stability Control Sys- The use of a fuse with a rating other than indicated tem Module/Stop may result in a dangerous electrical system over- Light Switch/Fuel...
MAINTAINING YOUR VEHICLE 499 3. Firmly grasp the lock ring and rotate it counterclock- LIGHT BULBS – Exterior Bulb No. wise to unlock it. Headlamp ......9008 H13 Front Park/Turn Signal Lamp.
500 MAINTAINING YOUR VEHICLE Front Turn Signal And Front Side Marker Lamp Front Fog Lamp 1. Turn the steering wheel all the way to the right to 1. Open the hood. access the left front turn signal or side marker. Turn the 2.
MAINTAINING YOUR VEHICLE 501 5. Install the bulb and socket assembly into the into the fog lamp housing, and rotate the connector clockwise to lock it in place. 6. Close the hood. Rear Tail/Stop, Turn Signal, And Back-Up Lamp 1. Open the liftgate. 2.
502 MAINTAINING YOUR VEHICLE 7. Pull the appropriate bulb(s) out of the back plate and 9. Connect the electrical connector. insert the replacement bulb(s). 10. Install the taillamp housing and screws. 8. Install the back plate and screws into the taillamp 11.
MAINTAINING YOUR VEHICLE 503 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 508
506 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE On Non-EVIC equipped vehicles, “Change Oil” will flash The Scheduled Maintenance services listed in this in the instrument cluster odometer and a single chime manual must be done at the times or mileages specified will sound, indicating that an oil change is necessary. to protect your vehicle warranty and ensure the best Based on engine operation conditions, the oil change vehicle performance and reliability.
Page 509
MAINTENANCE SCHEDULES 507 NOTE: referring to the steps described under “Electronic Vehicle • The oil change indicator message will not monitor the Information Center (EVIC)/Oil Change Required” in time since the last oil change. Change your vehicle’s “Understanding Your Instrument Panel” or under “In- oil if it has been six months since your last oil change, strument Cluster Description/Odometer/Trip Odom- even if the oil change indicator message is NOT...
Page 510
508 MAINTENANCE SCHEDULES Once A Month CAUTION! • Check tire pressure and look for unusual wear or • Failure to perform the required maintenance items damage. may result in damage to the vehicle. • Inspect the battery and clean and tighten the terminals •...
Page 511
MAINTENANCE SCHEDULES 509 8,000 Miles (13,000 km) or 16,000 Miles (26,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
510 MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 32,000 Miles (52,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 513
MAINTENANCE SCHEDULES 511 40,000 Miles (65,000 km) or 48,000 Miles (78,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 514
512 MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). Odometer Reading Date Repair Order #...
Page 515
MAINTENANCE SCHEDULES 513 64,000 Miles (104,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏...
Page 516
514 MAINTENANCE SCHEDULES 72,000 Miles (117,000 km) or 80,000 Miles (130,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 517
MAINTENANCE SCHEDULES 515 88,000 Miles (143,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). Odometer Reading Date Repair Order #...
Page 518
516 MAINTENANCE SCHEDULES 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏...
Page 519
MAINTENANCE SCHEDULES 517 104,000 Miles (169,000 km) or 112,000 Miles (182,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 520
518 MAINTENANCE SCHEDULES 120,000 Miles (195,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏...
Page 521
MAINTENANCE SCHEDULES 519 128,000 Miles (208,000 km) or 96 Months Maintenance Service 136,000 Miles (221,000 km) or Schedule 102 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 522
520 MAINTENANCE SCHEDULES 144,000 Miles (234,000 km) or 108 Months Maintenance Service 152,000 Miles (247,000 km) or Schedule 114 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 523
MAINTENANCE SCHEDULES 521 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Customer Assistance For The Hearing Or Vehicle......525 Speech Impaired (TDD/TTY) .
Page 526
524 IF YOU NEED CONSUMER ASSISTANCE Department Of Transportation Uniform Tire Traction Grades ..... 531 Quality Grades ......531 Temperature Grades .
IF YOU NEED CONSUMER ASSISTANCE 525 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
526 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (877) 426–5337 •...
IF YOU NEED CONSUMER ASSISTANCE 527 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
528 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment WARRANTY INFORMATION when you purchased the vehicle. An authorized dealer See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
IF YOU NEED CONSUMER ASSISTANCE 529 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 532
530 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC ve- maintaining, servicing, and repairing Chrysler Group hicles.
Page 533
IF YOU NEED CONSUMER ASSISTANCE 531 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 534
532 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 556
554 INDEX Voice Recognition System (VR) ....133 Window Fogging ......312 Windows .
Page 557
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use only frequency signals.
Page 558
Chrysler Group LLC Printed in U.S.A. 12KK74-126-AE 5th Edition...