Front Driving Mechanism Specifications; Rear Driving Mechanism Specifications; Battery/Charging System Specifications; Ignition System Specifications - Honda 2005-2008 RX500 FA Service Manual

'61HN252' by American Honda Motor Co. - Page 17 of 540
[2005-2008] [TRX500 FA/FGA]

FRONT DRIVING MECHANISM SPECIFICATIONS

Front differ-
ential

REAR DRIVING MECHANISM SPECIFICATIONS

Axle runout
Rear final
drive

BATTERY/CHARGING SYSTEM SPECIFICATIONS

Battery
Alternator

IGNITION SYSTEM SPECIFICATIONS

Spark plug
Spark plug gap
Ignition coil primary peak voltage
Ignition pulse generator peak voltage
Ignition timing (``F`` mark)

ELECTRIC STARTER SPECIFICATIONS

Starter motor brush length
1 of 1
ITEM
Oil capacity After draining
After disas-
sembly
Recommended oil
Gear backlash
Backlash difference
Slip torque
Face cam-to-housing distance
Differential ring gear depth
Cone spring height
ITEM
Oil capacity After draining
After disassembly
Recommended oil
Gear backlash
Backlash difference
Ring gear-to-stop pin clearance
ITEM
Capacity
Current leakage
Voltage Fully charged
(20°C/68°F)
Needs charging
Charging cur- Normal
rent
Quick
Capacity
Charging coil resistance (20°C/68°F)
ITEM
Standard
For cold climate (below 5°C/41°F)
ITEM
http://services.honda.com/ServiceManual/SVC_MNL/61HN253/61HN2...
GENERAL INFORMATION
STANDARD
185 cm (6.3 US oz, 6.5 Imp oz) 3
230 cm (7.8 US oz, 8.1 Imp oz)
3
Hypoid gear oil SAE #80
0.05 0.25 (0.002 0.010)
14 17 N·m (1.45 1.75 kgf·m,
10 13 lbf·ft)
3.3 3.7 (0.13 0.15)
6.55 6.65 (0.258 0.262)
2.8 (0.11)
STANDARD
3
75 cm (2.5 US oz, 2.6 Imp oz)
100 cm (3.4 US oz, 3.5 Imp oz)
3
Hypoid gear oil SAE #80
0.05 0.25 (0.002 0.010)
0.3 0.6 (0.01 0.02)
SPECIFICATIONS
12V 12 Ah
1 mA max.
13.0 13.2 V
Below 12.3 V
1.4 A x 5 10 h
6.0 A x 1.0 h
0.361 kW/5,000 rpm (min
0.1 1.0 Ω
SPECIFICATIONS
IJR7A9 (NGK), VX22BC (DENSO)
IJR6A9 (NGK), VX20BC (DENSO)
0.8 0.9 mm (0.03 0.04 in)
100 V minimum
0.7 V minimum
15° BTDC at idle
STANDARD
12.5 (0.49)
Unit: mm (in)
SERVICE LIMIT
0.4 (0.02)
0.2 (0.01)
12 N·m (1.2
kgf·m, 9 lbf·ft)
3.3 (0.15)
6.6 (0.26)
2.6 (0.10)
Unit: mm (in)
SERVICE LIMIT
3.0 (0.12)
0.4 (0.02)
0.2 (0.01)
)
-1
Unit: mm (in)
SERVICE LIMIT
9.0 (0.35)
1-11
3/9/2008 10:25 PM