AT command
AT+CGDCONT Sets host (APN) accessed when
establishing packet
transmission.
[M]
AT+CGEQMIN
Registers criterion determining
whether to permit QoS (Quality of
Service) sent from network when
establishing packet transmission.
[M]
AT+CGEQREQ Sets QoS (Quality of Service)
requested of network during
packet transmission.
[M]
AT+CGMR
Displays FOMA terminal
version.
*2
[M]
AT+CGREG=
Sets whether to send network
<n>
registration status. Service area
information (inside/outside) is
sent.
*1
[M]
AT+CGSN
Displays the FOMA terminal's
serial number.
[M]
AT+CLIP=<n>
Shows PC calling number when
receiving 64K data
communication.
[M]
AT+CLIR=<n>
Sets whether to send terminal's
phone number when establishing
64K data communication.
[M]
AT+CDIP=<n>
Sets whether to send an incoming
sub-address. Also, check the
status of Multi Number
subscription.
[M]
Overview
Refer to "More on AT commands" (nP. 31). Refer to "More on
*2
Refer to "More on AT commands" (nP. 32). Refer to "More on
*2
Refer to "More on AT commands" (nP. 33). Refer to "More on
*2
―
<n>
0:
1:
<stat>
0:
1:
4:
5:
*2
―
<n>
0:
1:
*1
<m>
0:
1:
2:
<n>
0:
1:
*2
2:
Displays +CLIR:<n>,<m> for AT+CLIR?.
<m>
0:
1:
2:
3:
4:
<n>
0:
1:
<m>
0:
1:
2:
Parameter/Explanation
Does not set (default setting)
Sets
When AT+CGREG=1 is set, information
is sent in the format "+CGREG:<stat>".
0, 1, 4 or 5 can be set for the <stat>
parameter.
Outside area
Inside area (home)
Unknown
Inside area (visitor)
Does not output results (default setting)
Outputs results
Displays +CLIP:<n>,<m> for "AT+CLIP?".
NW setting to not send own number
during transmissions
NW setting to send own number during
transmissions
Unknown
Follows the service agreement
Does not send
Sends (default setting)
CLIR is not running (always send)
CLIR is always running (never send)
Unknown
CLIR temporary mode (default setting is
Do not send)
CLIR temporary mode (default setting is
Send)
Does not display sub-addresses
(default setting)
Displays sub-addresses
Multi Number is not subscribed
Subscribing Multi Number
Unknown
25
Execution
example
AT commands"
(nP. 31).
AT commands"
(nP. 32).
AT commands"
(nP. 33).
AT+CGMRo
12345678901234
56
OK
AT+CGREG=1o
OK
(Set to send)
AT+CGREG?o
+CGREG:1,0
OK
(Indicates outside
area)
+CGREG:1
(Moved from
outside area to
inside area)
AT+CGSNo
123456789012345
OK
AT+CLIP=0o
OK
AT+CLIP?o
+CLIP:0,1
OK
AT+CLIR=0o
OK
AT+CLIR?o
+CLIR:2,3
OK
AT+CDIP=0o
OK
AT+CDIP?o
+CDIP:0,1
OK
Need help?
Do you have a question about the SH-05A and is the answer not in the manual?