Basic Ip Commands - D-Link xStack DES-3528 Series Cli Reference Manual

xStack® DES-3528/DES-3552 Series Layer 2 Fast Ethernet Managed Switch CLI Reference Guide
B IP C
ASIC OMMANDS
The IP interface commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in
the following table.
Command
config ipif
create ipif
delete ipif
show ipif
enable ipif
disable ipif
enable ipif_ipv6_link_local_auto
disable ipif_ipv6_link_local_auto
show ipif_ipv6_link_local_auto
Each command is listed, in detail, in the following sections.
config ipif
Purpose
Syntax
Description
Parameters
Parameters
<ipif_name 12> [{ipaddress <network_address> | vlan <vlan_name 32> |
proxy_arp [enable | disable] {local [enable | disable]} | state [enable | disable]}
| bootp | dhcp | ipv6 [ipv6address <ipv6networkaddr> | state [enable | disable]]
| ipv4 state [enable | disable] | dhcpv6_client [enable | disable]]
<ipif_name 12> {<network_address>} <vlan_name 32> {state [enable | disable]
| proxy_arp[enable | disable] {local [enable | disable]}}
[<ipif_name 12> {ipv6address <ipv6networkaddr>} | all]
{<ipif_name 12>}
[<ipif_name 12> | all]
[<ipif_name 12> | all ]
[<ipif_name 12> | all]
[<ipif_name 12> | all]
{<ipif_name 12>}
Used to configure the IP interface.
config ipif <ipif_name 12> [{ipaddress <network_address> | vlan <vlan_name 32> |
proxy_arp [enable | disable] {local [enable | disable]} | state [enable | disable]} | bootp |
dhcp | ipv6 [ipv6address <ipv6networkaddr> | state [enable | disable]] | ipv4 state
[enable | disable] | dhcpv6_client [enable | disable]]
This command is used to configure the IP interface on the Switch.
<ipif_name 12> − Enter an alphanumeric string of up to 12 characters to identify this IP
interface.
ipaddress <network_address> − IP address and netmask of the IP interface to be created.
Users can specify the address and mask information using the traditional format (for
example, 10.1.2.3/255.0.0.0) or in CIDR format (10.1.2.3/8).
<vlan_name 32> − The name of the VLAN corresponding to the System IP interface.
state [enable | disable] − Allows users to enable or disable the IP interface.
proxy_arp [enable | disable] – Allows users to enable or disable the proxy ARP function. The
default setting is Disabled.
local [ enable | disable] - Controls whether the system provides the proxy reply for the ARP
packets destined for IP address located in the same subnet as the received interface.When
proxy ARP is enabled for an interface, the system will reply the ARP query destined for IP
address located in a different IP subnet from the interface IP. For ARP packets destined for
IP address located in the same IP subnet as the interface IP, the system will check this
setting to determine whether to reply. The default setting is Disabled.
bootp − Allows the selection of the BOOTP protocol for the assignment of an IP address to
the Switch's System IP interface.
dhcp − Allows the selection of the DHCP protocol for the assignment of an IP address to the
Switch's System IP interface. If users are using the autoconfig feature, the Switch becomes a
DHCP client automatically so it is not necessary to change the ipif settings.
ipv6 – Specifies that IPv6 address will be enabled or disabled.
ipv4 - Specifies that IPv4 address will be enabled or disabled.
160