Table of Contents
Advertisement
Section 5 OTHER CONVENIENT FUNCTIONS
3 Selecting between 1-sided or 2-sided copies
This procedure selects the type of finished copies to be made
between 1-sided and 2-sided.
1
With the content of the "Basic" tab displayed, touch the "1
sided/2 sided" key. The "1 sided/2 sided" screen will be
displayed.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Job Build - Step1
1-sided
1 sided copy
11x8
1
/
"
2
Select
Original
1 sided/
paper
type
2 sided
None
AMS
Back Edge
Reduce
Orig. set
Finished
/Enlarge
direction
Basic
Quality
Edit
Metric specifications
Ready to Job build.
Set original. Press Start key.
Job Build
-Step 1
1-sided
1-sided Copy
Select
Original
1-sided/
paper
type
2-sided
Back Edge
None
AMS
Reduce/
Orig. set
Finished
Enlarge
direction
Basic
Quality
Edit
NOTE
The setting in regard to making either 1-sided or 2-sided copies can
only be made in the first step of the job build mode and will apply to
all steps in the copy job.
2
Touch the "1 sided" key or the "2 sided" key, as appropriate,
and then select the binding direction you want for the
finished copies.
Follow the instructions on the right side of the touch panel
and verify the direction in which the originals were set.
Inch specifications
Ready to Job build.
Place originals then press Start key.
1 sided/ 2 sided copy
Finished
1 sided
Open from
copy
left
2 sided
Open from
copy
right
Open from
top
Metric specifications
Ready to Job build.
Set original. Press Start key.
1-sided / 2-sided Copy
Finished
1-sided
Left
Copy
binding
2-sided
Right
Copy
binding
Top
binding
IMPORTANT!
If the designation for the direction that the originals are set is not
correct, copying may be accomplished incorrectly.
5-64
4 Selecting how to finished up the copy sets
If the optional Document Finisher is installed on your copier, this
procedure lets you select whether to staple or hole punch the finished
copy sets.
Set
End
Insert
page
1 sided copy-Left
Finished page #:0
Set
End
Insert
blank page
1-sided Copy-Left
Finished page #: 0
The setting in regard to how the copy sets will be finished can only be
made in the first step of the job build mode and will apply to all steps
in the copy job.
Set
Back
Close
Check direction
Check direction of
original top side.
Left top
Back Edge
corner
Set
Back
Close
Check direction
Check direction of original.
Left top
Back Edge
corner
3
Touch the "Close" key. The touch panel will return to the
screen in step 1.
1
With the content of the "Basic" tab displayed, touch the
"Finished" key. The "Finished" screen will be displayed.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Job Build - Step1
1-sided
1 sided copy
11x8
1
/
"
2
Select
Original
1 sided/
paper
type
2 sided
None
AMS
Back Edge
Reduce
Orig. set
Finished
/Enlarge
direction
Basic
Quality
Edit
Metric specifications
Ready to Job build.
Set original. Press Start key.
Job Build
-Step 1
1-sided
1-sided Copy
Select
Original
1-sided/
paper
type
2-sided
Back Edge
None
AMS
Reduce/
Orig. set
Finished
Enlarge
direction
Basic
Quality
Edit
NOTE
2
Select how you want the copy sets to be finished by touching
the "Staple mode" key, the "Saddle Stitch" ["Center Staple" ]
key or the "Punch mode" key, as appropriate.
Follow the instructions on the right side of the touch panel
and verify the direction in which the originals were set.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Finished
Sorting
Staple
No cover
Staple
None
mode
1 set
Saddle
Stitch
Metric specifications
Ready to Job build.
Set original. Press Start key.
Finished
Group
Staple
Group
None
Staple
None
None
Mode
1 set
1 set
Center
Staple
Set
End
Insert
page
1 sided copy-Left
Finished page #:0
Set
End
Insert
blank page
1-sided Copy-Left
Finished page #: 0
Set
Back
Close
Punch
Check direction
Check direction of
No cover
original top side.
Punch
mode
Left top
Back Edge
corner
Set
Back
Close
Punch
Check direction
Check direction of original.
None
Punch
Mode
Left top
Back Edge
corner
Advertisement
Table of Contents
