Panasonic AJ-HPD2500 Operating Instructions Manual page 209

Item Message
UNKNOWN DATA!
USER CLIP NAME
Thumbnail MODIFIED!
WRITE PROTECTED! The P2 or SD memory card is write protected.
CANNOT ACCESS
CARD!
CANNOT ACCESS
TARGET!
CANNOT COPY!
FORMAT HDD TO
FAT
CANNOT FORMAT!
CANNOT
RECOGNIZE HDD!
CANNOT SELECT!
MAX.6 PARTITIONS
CARD IS EMPTY!
CANNOT COPY!
FORMAT P2 CARD!
Hard disk
HDD CAPACITY
FULL!
HDD
DISCONNECTED!
MISMATCH
COMPONENT!
P2 CARD IS
UNFORMATTED!
TOO MANY
PARTITIONS!
TOO MANY
TARGETS!
UNKNOWN DEVICE
CONNECTED!
VERIFICATION
FAILED!
CANNOT CHANGE!
On-screen
keyboard
CANNOT SET!
INVALID VALUE!
CANNOT FIND CLIP! Specified clip could not be found.
CANNOT FIND SAME
FORMAT!
CANNOT MOVE!
CANNOT OPERATE
AT "RED" EVENT!
Playlist
CANNOT OPERATE
WITH EXTERNAL
PLAYER
CANNOT OPERATE:
"RED" A.DUB EVENT
INCLUDED
Description
The metadata character code is invalid.
Characters in the clip name had to be deleted in
adding the counter value.
An error occurred during P2 card access.
An error occurred during hard disk access.
Clips cannot be copied to hard disk without
partitions.
The hard disk cannot be initialized.
The destination target cannot be properly
recognized.
It is not possible to mount more than 6 hard disk
partitions simultaneously.
The P2 selected for copying is empty.
Importing is not possible to a P2 card containing
clips.
Not enough space left on the hard disk.
The unit is not connected to a hard disk.
Copying is not possible since the model numbers
of the two cards differ.
The P2 card is not formatted.
There are too many partitions.
Multiple devices are connected.
The connected DVD drive is not compatible.
The compare check after copying failed.
An attempt was made to change PERSON when
no text memo had been entered.
The entered value is invalid.
There are no clips in a matching playlist format.
Move operation is not possible.
Not allowed in a playback disable (marked red)
event.
A.DUB is not available when an external player is
used.
Since the selected events include a red A.DUB
event, operation is not possible.
Use UTF-8 for the metadata character code. Use the
viewer to enter correct characters.
The user clip name plus the counter value can only
contain up to 100 bytes. Characters in the clip name
are automatically deleted when the total exceeds
100 bytes.
Insert write-enabled media.
Check P2 card.
Check hard disk status and connection.
Format using a FAT format or export data from a P2
card to create a partition.
Connect another hard disk drive.
Reboot the hard disk or connect a different hard
disk.
Cancel some of the selected partitions.
Copying is not performed since the card is empty.
Format the P2 card.
There is not enough space on the connected hard
disk. Use a new hard disk or formatted hard disk.
Reconnect the USB cable. If the hard disk does not
operate normally, turn it off and turn it back on again.
Use a P2 card with the same model number or
import video in clip units.
Use a formatted P2 card.
Hard disks can handle up to 23 partitions. Use a new
hard disk or formatted hard disk.
Disconnect devices, turn off the unit and turn it back
on again.
Disconnect devices, turn off the unit and turn it back
on again.
Copy the data again.
First enter a text memo.
Enter a valid value.
Insert the card with the clip.
Use clips that match the playlist format.
Select a consecutive area.
An illegal operation was attempted in a disabled
event. Use a playback enable event or insert a card
with suitable clips.
Select a P2 card as a player.
Remove the red A.DUB event from the selection.
For Long and Trouble-Free Operation: Error Messages
Measure
209