Panasonic AJ-HPD2500 Operating Instructions Manual page 206

Monitor display
Displayed when a voice-over recording is attempted on a P2 card or when
LACK OF REC
external device is selected for a player of the playlist and the REC button is
CAP.
pressed to start recording, while there is not enough free space on the card.
Displayed for two seconds when a shot mark is added or deleted.
MARK ON/OFF
MAX. EVENTS The number of events that can be registered on the playlist has been reached.
NEED TO REPAIR Displayed when an SD memory card that needs to be repaired is detected.
SD (When an AJ-YCX250G AVCHD codec board (optional) is installed.)
Displayed for the first two seconds when the REC button is pressed to enter the
NO INPUT EE mode and the VIDEO IN (SHIFT + EDIT MODE) or AUDIO IN (SHIFT + VIDEO)
is set to a connector with no input except for analog audio signals.
PL FILE NOT Displayed when a voice-over recording is attempted on a P2 card and there is no
FOUND playlist file.
Displayed when recording cannot continue because there is no space or
REC LIMIT SD because a 12-hour recording has been completed.
(When an AJ-YCX250G AVCHD codec board (optional) is installed.)
Displayed when an SD memory card clip is being repaired.
REPAIRING SD
(When an AJ-YCX250G AVCHD codec board (optional) is installed.)
R-OUT NOT Displayed when an attempt was made to use a recorder OUT point during insert
AVAILABLE editing in playlist mode.
SLOT SEL Displayed when the SLOT SELECT +/– button was pressed while it is not possible
INVALID to switch P2 card recording slot.
TEXT MEMO Displayed for two seconds when a text memo is added.
TEXT MEMO Appears when there are already 100 text memos and no more memos can be
INVALID added.
WRITE Appears when a voice-over recording is attempted on a write-protected P2 card.
PROTECTED
WARNING information
If "E- * * " Iights in the monitor display, hold down the SHIFT button and press the MENU button to open the DIAG-MENU and
read the warning information.
Display
No Character code
10 FAN STOP
21 REC WARNING
CARD
26
ERROR<******>
49 LAN ERROR
50 BATTERY EMPTY
DIR NG
70
CARD<******>
RUNDOWN
71
CARD<******>
◆ NOTE
*1: "E-50" appears when the backup battery is depleted. Consult your supplier for information on a store that can provide you with a new battery
(CR2032 or the equivalent). Be sure to use setup menu No. 069 (CLOCK SET) to set the clock after battery replacement.
*2: Operation continues but normal recording or playback may not be possible.
206
For Long and Trouble-Free Operation: Error Messages
Description
Displayed when the fan motor stops.
Displayed when a video or audio error occurs during recording.
To continue operation, turn the power off and then back on again.
Displayed when data was corrupted due to a P2 card error during recording.
This error is displayed after recording ends and remains on until the start of the next operation. This
error is not displayed during playback. (* indicates the slot number where the error occurred.)
Replace the P2 card in the slot where the error occurred.
Displayed when a LAN connection or disconnection failed. Power off, then power up
again before use.
Should E-49 appear again, consult your supplier.
Displayed when a drop in the backup battery voltage for the internal clock is detected at
power on. Replace the internal battery.
The P2 card directory structure is not supported. (* indicates the slot number where the
error occurred.) Make a quick backup of card data and format the card.
The maximum number of overwrites has been exceeded. (* indicates the slot number
where the error occurred.) This P2 card should be replaced.
Description
*1
Deck operation Counter display
Operation continues CANTADUB
MARK ON /
Operation continues
MARK OFF
Operation continues Counter value
Operation continues ND REP
Operation continues NO INPUT
Operation continues CANTADUB
Operation continues LIMIT SD
Operation continues REPAIR
Operation continues Counter value
Operation continues INVALID
Operation continues TEXT MEMO
Operation continues INVALID
Operation continues CANTADUB
Deck operation
Operation
continues
STOP
STOP
STOP
Operation
continues
Operation
continues
Operation
*2
continues