Removing And Installing The Ac-Input Power Supplies - Cisco 6503 - Catalyst Firewall Security Sys Installation Manual

Removing and Installing the AC-Input Power Supplies

The switch can bring up only an identical replacement module online. To support OIR of an identical
module, the module configuration is not removed from the running-config file when you remove a
module.
If the replacement module is different from the removed module, you must configure it before the switch
can bring it online.
Layer 2MAC addresses are stored in an EEPROM, which allows modules to be replaced online without
requiring the system to update switching tables and data structures. Regardless of the types of modules
installed, the Layer 2 MAC addresses do not change unless you replace the supervisor engine. If you do
replace the supervisor engine, the Layer 2 addresses of all ports change to those specified in the address
allocator on the new supervisor engine.
For instructions on installing and replacing modules, refer to the Catalyst 6500 Series Ethernet Modules
Installation Guide.
Removing and Installing the AC-Input Power Supplies
This section describes how to remove and install AC power supplies in the Catalyst 6500 series chassis.
The AC-input power supplies have three different form factors, which are not interchangeable between
the Catalyst 6500 series chassis.
supported on, and the corresponding removal and replacement procedures.
Table 4-1 Catalyst 6500 Series AC-Input Power Supplies Removal and Installation Procedures
Power Supply
950 W (PWR-950-AC)
1400 W (PWR-1400-AC)
2700 W (PWR-2700W-AC)
1000 W (WS-CAC-1000W)
1300 W (WS-CAC-1300W)
2500 W (WS-CAC-2500W)
3000 W (WS-CAC-3000W)
4000 W (WS-CAC-4000W)
6000 W (WS-CAC-6000W)
1
8700 W (WS-CAC-8700W-E)
1. While the 8700 W power supply can be installed in any Catalyst 6500 series chassis with the exception of the 3-slot and the 4-slot chassis, the power
supply's form-factor is slightly different from the other power supplies listed. The form-factor difference requires you to move the system ground from
the chassis ground pad on the Catalyst 6506, Catalyst 6509, or Catalyst 6509-NEB chassis to the power supply system ground lugs.
2. The 2500 W AC-input power supply is not supported on the Catalyst 6513-E switch chassis.
Catalyst 6500 Series Switches Installation Guide
4-2
Table 4-1
Chassis Supported
Catalyst 6503
Catalyst 6503-E
Catalyst 6504-E
Catalyst 6506
Catalyst 6509
Catalyst 6509-NEB
Catalyst 6506
Catalyst 6506-E
Catalyst 6509
Catalyst 6509-E
Catalyst 6509-NEB
Catalyst 6509-NEB-A
Catalyst 6509-V-E
Catalyst 6513
2
Catalyst 6513-E
Chapter 4
lists the AC-input power supplies, the chassis that they are
Removal and Installation Procedure
"Removing and Installing the 950 W and
1400 W AC-Input Power Supplies" section on
page 4-3
"Removing and Installing the 2700 W
AC-Input Power Supply" section on page 4-6
"Removing and Installing the 1000 W,
1300 W, 2500 W, 3000 W, 4000 W, 6000 W,
and 8700 W AC-Input Power Supplies" section
on page 4-9
"Removing and Installing the 1000 W,
1300 W, 2500 W, 3000 W, 4000 W, 6000 W,
and 8700 W AC-Input Power Supplies" section
on page 4-9
Removal and Replacement Procedures
OL-5781-08