Extron electronics NetPA Ultra Series User Manual page 100

Command SIS Command
Function (Host to Device)
Audio Mute
Audio mute
E
Audio unmute
E
Mute status
E
Audio Group Master Commands
NOTES:
•
For information on configuring groups, see
•
A group must have assigned members for these commands to have an effect.
X7$
•
For , a positive (+) value is assumed unless a negative (-) value is specified.
X7$
•
If entering an value outside the valid range for the group or outside the soft limits, the amplifier responds with:
For gains:
For mutes:
E
Set a group fader value
E
Example:
E
Increment a group fader
value
E
Example:
E
Decrement a group fader
value
E
View the group fader
value
Verbose mode 2/3
E
Mute a group
E
Unmute a group
E
View a group mute value
E
Set soft limits
X1&
E
Example:
View soft limits
E
Verbose mode 2/3
KEY:
X1$
=
Group master number
X1^ =
Group fader setting
X1& =
Group fader soft limit
X7@
Target OID
X7$ =
Mute
Response
(Device to Host)
X7@ }
M *1AU DsM
X7@ }
M *0AU DsM
X7@ }
M AU DsM
Groups on page 65.
The maximum upper/lower range of the soft limit or maximum upper/lower range of the group.
X7$
E13 error (invalid parameter
X1$ X1^ }
D * GRPM GrpmD
}
D2*-239GRPM GrpmD 2*-293
X1$ X2) }
D * +GRPM GrpmD
}
D2*30+GRPM GrpmD2*-263
X1$ X2) }
D * - GRPM GrpmD
X1$ } X1^]
D GRPM
GrpmD
X1$ }
D *1GRPM Grpm D
X1$ }
D *0GRPM Grpm D
X1$ }
D GRPM Grpm D
X1$ X1&
L * GrpmL
*
upper
}
lower GRPM
}
L2*60*-60GRPM GrpmL2*60*-60
X1$ } X1&
L GRPM
GrpmL
1 through 32
dB value in 0.1 dB steps, using negative numbers and eliminating decimal places using a 10x multiplier.
-100.0dB to +80.0 dB is represented by -1000 to 800. The valid range depends on the type of gain or trim
block assigned to the group number (
dB value in 0.1 dB steps. Gain uses 10x multiplier (+10 dB = 100+).
See Object ID (OID) Number Tables on page 97.
0 = Unmute
X7@ ]
*1
X7@ ]
*0
X7@ X7$]
*
X1$ X1^
, , and values can be sent without leading zeroes.
X1$ X1^]
*
]
X1$ X1^]
*
]
X1$ X1^]
*
X1$ X1^]
*
X1$ ]
*1
X1$ ]
*0
X1$ X7$]
*
X1$ X1& X1&]
* *
]
X1&]
*
X1$ X1& X1&]
* *
X1$
).
1 = Mute
NetPA Ultra Series • Remote Control and Configuration
Additional Description
X7@
Mute audio at .
X7@
Unmute audio at .
X1^
Set a group fader to a value of
Set group 2 fader control to -29.3 dB.
X1$ X2)
Increase the level of by dB.
Raise the group 2 fader 3 dB from -29.3 dB
(set in example above) to -26.3 dB.
X1$
Decrease the level of the group fader
X2)
by dB.
X1$
Mute all blocks in group .
X1$
Unmute all blocks in group .
X7$
For group masters, is always expressed
as an unsigned or negative value.
X1&
Set the groups soft limits to
upper
X1&
.
lower
Set the upper soft limit for the group 2 fader
to +6.0 dB and the lower limit to -6.0 dB.
.
.
and
93