Recommended Test Equipment - Anritsu Spectrum Master MS2722C Maintenance Manual

1-3 Recommended Test Equipment

1-3 Recommended Test Equipment
The following test equipment is recommended for use in testing and maintaining Anritsu Models MS2722C,
MS2723C, MS2724C, MS2725C, and MS2726C.
• Table 1-1 is a list of test equipment that is required for verifying the spectrum analyzer functions on
Models MS2722C, MS2723C, and MS2724C.
• Table 1-2 is a list of test equipment that is required for verifying the spectrum analyzer functions on
Models MS2725C, and MS2726C.
• Table 1-3 is a list of test equipment that is required for verifying the functions of installed options on any
MS272xC Model.
• Table 1-4 is a list of replaceable parts for the MS272xC Spectrum Master.
Table 1-1. Test Equipment Required for Verifying Spectrum Analyzer Functions up to 20 GHz
Instrument
Synthesized Signal Generator
Power Meter
Power Sensor
50 ohm Termination
Adapter
Adapter
RF Coaxial Cable
Lowpass Filter
Frequency Reference
Signal Generator
Fixed Attenuator
Fixed Attenuator
Fixed Attenuator
Fixed Attenuator
Power Splitter
Coaxial Cable
a. Note that MG3692A models require Option 15 to achieve power of +16 dBm at 3.5 GHz. MG3692B models do not require
Option 15 to achieve power of +16 dBm at 3.5 GHz.
Factory tests have shown that the equipment that is listed above will provide satisfactory results at
20 GHz (the upper limit of the MS2724C) even though the chart above specifies 18 GHz
Caution (per manufacturers specifications). Many Type N cables have excessive loss for testing the
spectrum analyzer section of the instrument up to 20 GHz. An SMA cable or K cable should
therefore be installed on the MG synthesizer for all spectrum analyzer tests on the MS2724C.
1-2
Critical Specification
Frequency: 0.1 Hz to 20 GHz
Power Output: +16 dBm
Step attenuator installed
Power Range: –70 to +20 dBm
Frequency: 100 kHz to 18 GHz
Power Range: –67 to +20 dB
Frequency: DC to 18 GHz
Frequency: DC to 20 GHz
N(m)-N(m), 50 ohm
Frequency: DC to 20 GHz
K(m)-N(f), 50 ohm
Frequency: DC to 18 GHz
N(m)-N(f), 50 ohm
Frequency: 50 MHz
Frequency: 10 MHz
10 dB Attenuation
20 dB Attenuation
6 dB Attenuation
2 dB Attenuation
Frequency: DC to 18 GHz
BNC(m) to BNC(m), 50 ohm
PN: 10580-00279 Rev. E
Chapter 1 — General Information
Recommended Manufacturer/Model
Anritsu Model MG3692A or MG3692B
with Options 2A, 4, 22, 15x
Anritsu Model ML2438A
Anritsu Model MA2421D or SC7400
(Qty 2)
Anritsu Model 28N50-2
Anritsu Model 34NN50A
Anritsu Model 34RKNF50
Anritsu Model 15NN50-1.5B (Qty 2)
Anritsu Part Number 1030-96
Symmetricom RubiSource T&M
Agilent Model 8648D with Options 1ES
and 1EA
Aeroflex/Weinschel Model 44-10 (Qty 2)
Aeroflex/Weinschel Model 44-20 (Qty 2)
Aeroflex/Weinschel Model 44-6 (Qty 2)
Aeroflex/Weinschel Model 44-2 (Qty 2)
Aeroflex/Weinschel Model 1870A
Any (Qty 2)
a
MS272xC MM