ferrotec Temescal CV-12SLX User Manual page 5

List of Illustrations
Figure Number and Title
Figure 1-1 CV-12SLX HVPS Front Panel ....................................................................................................................... 1-1
Figure 1-2 Filament Power Supply Front Panel ............................................................................................................ 1-2
Figure 1-3 EBC Main Control Unit and Hand-Held Controller ......................................................................................... 1-3
Figure 2-1 Mounting Hole Pattern for FPS Module(s) .................................................................................................... 2-4
Figure 2-2 Facility Low Impedance Grounding Requirements ........................................................................................ 2-5
Figure 2-3 System Low Impedance Grounding Requirements ....................................................................................... 2-6
Figure 2-4 Rear Panel of Single Gun CV-12SLX HVPS ................................................................................................... 2-7
Figure 2-5 Rear Panel of Dual Gun CV-12SLX HVPS ..................................................................................................... 2-7
Figure 2-6 Grounding Studs on FPS Front Panel .......................................................................................................... 2-8
Figure 2-7 Input Power Connections to 208-Volt HVPS Units ...................................................................................... 2-10
Figure 2-8 Input Power Connections to 400-Volt HVPS Units ...................................................................................... 2-10
Figure 2-9 Input Power and HV Connections on FPS Front Panel ................................................................................ 2-11
Figure 2-10 Removing the FPS Conduit Panel .............................................................................................................. 2-12
Figure 2-11 Conduit Properly Secured to FPS Conduit Panel ......................................................................................... 2-12
Figure 2-12 HV Output Cables Secured to Studs inside FPS .......................................................................................... 2-13
Figure 2-13 HV Conduit Bracket Properly Installed on HV Feedthrough ......................................................................... 2-13
Figure 2-14 HV Conduit Properly Secured to Bracket .................................................................................................... 2-14
Figure 2-15 Control/Data Cable Connections on FPS Front Panel .................................................................................. 2-14
Figure 2-16 System I/Os Exchanged via HVPS Rear Panel Connector J4 and the HVPS I/O Cable (PN 0620-6682-0) ....... 2-16
Figure 2-17 System I/Os Exchanged via FPS Front Panel Connector J101 and the FPS I/O Cable (PN 0620-6672-2) ....... 2-18
Figure 3-1 CV-12SLX HVPS Front Panel ....................................................................................................................... 3-1
Figure 3-2 Filament Power Supply Front Panel ............................................................................................................ 3-2
Figure 3-3 EBC's Operations>E-Beam Screen when Beam Is Off .................................................................................. 3-4
Figure 3-4 Operations>E-Beam Screen, Beam On at 0.0 mA ........................................................................................ 3-4
Figure 3-5 Operations>E-Beam Screen when Gun is On and HV is Off .......................................................................... 3-5
Figure 3-6 Operations E-Beam Screen with Numeric Keypad Displayed ......................................................................... 3-5
Figure 3-7 Operations>E-Beam Screen, Beam on at 5% Power .................................................................................... 3-6
Figure 3-8 The EBC's Diagnostics Screen .................................................................................................................... 3-6
Figure 3-9 Remote Controller's LOCAL Screen, Menu 1 Selected, Beam and Sweep Off .................................................. 3-8
Figure 3-10 HVPS Front Panel LEDs: HVPS Powered Up in Nominal State, with HV and FPS Off ........................................ 3-9
Figure 3-11 HVPS Front Panel LEDs when Subthreshold Arcing is Occurring .................................................................. 3-12
Figure 3-12 HVPS Front Panel LEDs when a Latched OUTPUT ARCING Fault Has Occurred ............................................ 3-12
Figure 4-1 Single-Gun CV-12SLX HVPS Rear Panel ....................................................................................................... 4-1
Figure 4-2 Dual-Gun CV-12SLX HVPS Rear Panel ......................................................................................................... 4-2
Figure 4-3 Filament Power Supply (FPS) Module .......................................................................................................... 4-4
Figure 4-4 Component Location in Standard FPS Units (PN 0620-6604-0 and -1) ........................................................... 4-5
Figure 4-5 Top Level Block Diagram for Standard FPS Units (PN 0620-6604-0 and -1) ................................................... 4-6
Figure 4-6 Component Location in FPS Units with PN 0620-6604-2 ............................................................................... 4-7
Figure 4-7 Top Level Block Diagram for FPS Units with PN 0620-6604-2 ....................................................................... 4-7
Figure 4-8 Filament Supply PCB Overview Block Diagram ............................................................................................. 4-8
Figure 4-9 Block Diagram of Filament Supply PCB Control and Power Circuits ............................................................. 4-10
Figure 4-10 Emission Current Ramp Circuit ................................................................................................................. 4-11
Figure 4-11 Autobias Circuit Block Diagram ................................................................................................................. 4-12
Figure 5-1 HVPS Front Panel LEDs .............................................................................................................................. 5-2
Figure 5-2 Status Indicator LEDs ................................................................................................................................ 5-2
Figure 5-3 Sub-Threshold Arcing: Arc/Out Of Regulation and Output Arcing LEDs ......................................................... 5-3
Figure 5-4 Filament Load Fault and Filament Power LEDs ............................................................................................ 5-3
Figure 5-5 HVPS Front Panel LEDs with Latching Fault LEDs Outlined ........................................................................... 5-4
Figure 5-6 Interlocks OK and Rail Undervoltage LEDs .................................................................................................. 5-4
Figure 5-7 HV Overcurrent and HV Overvoltage LEDs .................................................................................................. 5-5
Figure 5-8 Setpoint Overvoltage and Output Arcing LEDs ............................................................................................. 5-5
Figure 5-9 Inverter Overload and Overtemperature LEDs ............................................................................................. 5-5
Figure 5-10 Aux Supply Low and External Control Fault LEDs ......................................................................................... 5-6
0101-8292-0, Rev. C iii
r
Page Numbe
CV-12SLX User Manual