Sharp MX-M356N Service Manual page 125

: '15/Aug.
1
44-14
Purpose Operation data display
Function (Purpose) Used to display the output level of the tem-
perature and humidity sensor.
Section Process (OPC drum, development)/Fusing/
LSU
Operation/Procedure
The output levels of the fusing temperature sensor, the machine
temperature sensor, and the humidity sensor are displayed.
Item/ Content
Display
TH_UM Fusing upper thermistor main
detection temperature
Fusing upper thermistor main
detection temperature A/D value
TH_US Fusing upper thermistor sub
detection temperature
Fusing upper thermistor sub
detection temperature A/D value
TH_RA Temperature thermistor
Temperature thermistor A/D value
HUD_RA Humidity sensor
Humidity sensor A/D value
44-43
Purpose Data display
Function (Purpose) Used to display the identification informa-
tion of the developing unit.
Section Developing system
Operation/Procedure
The identification number and the identification signal level of the
developing unit are displayed.
Item/Display Content
A DVCH K developing unit
KIND K identification
number
B DV_TYP_ K developing unit
SEL_K identification
detection
C DVCH_ K developing unit
AD_K identification AD
value
Display range
Temperature:
0 - 255 degree C (+/- 1
degree C)
AD value: 0-1023
Temperature:
0 - 255 degree C (+/- 1
degree C)
AD value: 0-1023
Temperature:
- 40.0-60.0 degree C (+/
- 0.1 degree C)
AD value: 0-123
Humidity:
5.0-90.0% (+/- 0.1%)
AD value: 0-1023
Display
NOTE
range
1 - 9 The model
identification number of
the developing unit
which is backed up in
the EEPROM of the
machine.
0 - 1 0 = High (Open)
1 = Low (GND)
0 - 255 AD value of the
developing unit
identification voltage
MX-M316N SIMULATION 6 – 46
46
46-2
Purpose Adjustment (Monochrome copy mode)
Function (Purpose) Used to adjust the copy density in the copy
mode.
Section
Operation/Procedure
1) Select an adjustment target item with scroll key on the touch
panel.
2) Enter the set value with 10-key.
* When the key is pressed, the setting value of each
item can be changed with 1up (1down) collectively.
3) Press [OK] key. (The set value is saved.)
To adjust the copy density in the low density area, select the "LOW"
mode and change the adjustment value. To adjust the copy density
in the high density area, select the "HIGH" mode and change the
adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy den-
sity is decreased.
Item/Display
A AUTO1 Auto 1
B AUTO2 Auto 2
C TEXT Text
D TEXT/PRINTED Text/Printed
PHOTO Photo
E TEXT/PHOTO Text/Photograph
F PRINTED PHOTO Printed Photo
G PHOTOGRAPH Photograph
H MAP Map
I AUTO1 Auto 1 (copy
to copy)
J AUTO2 Auto 2
(copy to copy)
K TEXT Text
(copy to copy)
L TEXT/PRINTED Text printed
PHOTO photo
(copy to copy)
M PRINTED PHOTO Printed photo
(copy to copy)
Setting Default
Content
range value
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
LOW 1 - 99
HIGH 1 - 99
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
1
50
50
50
50
50
50
50
50
50
50