Advertisement
46-19
Purpose
Setting
Function (Purpose) Used to set the operating conditions for the
density scanning (exposure) of mono-
chrome auto copy mode documents.
Section
Operation/Procedure
Select an item to be set with touch panel.
When an item is selected, it is highlighted and the setting change is
saved.
Item/Display
Content
AE_MODE
Auto exposure mode
AE_STOP_COPY
Auto B/W exposure
Stop (for copy)
AE_STOP_FAX
Auto B/W exposure
Stop (for FAX)
AE_STOP_SCAN
Auto B/W exposure
Stop (for scanner)
AE_FILTER
Auto exposure filter
setting
AE_WIDTH
AE exposure width
46-30
Purpose
Adjustment/Setup
Function (Purpose) Used to adjust the resolution in the sub
scanning direction in the copy mode.
Section
Operation/Procedure
1)
Refer to the following table, and enter the set value corre-
sponding to the resolution mode with 10-key.
2)
Press [OK] key. (The set value is saved.)
Item/Display
A
SCAN
Scan resolution
RESOLUTION
selection
SW
(COPY: COLOR)
Resolution in the sub scanning direction (DPI)
Scan
25-99%
Mode
mode
[Magnification
ratio]
Mode1
OC
600
RSPF
600
Mode2
OC
300
RSPF
400
Set value
MODE1, MODE2
MODE2
REALTIME/
STOP
STOP/
PRESCAN
ON/OFF
ON
REALTIME/
STOP
STOP/
PRESCAN
SOFT
NORMAL
NORMAL
SHARP
FULL/PART
FULL
Setting
Content
range
Mode1
0 - 1
0
Mode2
1
100-200%
201-400%
[Magnification
[Magnification
ratio]
ratio]
600
1200
600
600
1200
600
MX-M316N SIMULATION 6 – 48
46-32
Purpose
Function (Purpose) Used to adjust the document background
Section
Operation/Procedure
1)
Select a target item of setting with scroll key on the touch
panel.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
Default
When the adjustment value is increased, reproducibility of the
value
background and the low density image is increased. When the
adjustment value is decreased, reproducibility of the background
and the low density image is decreased.
Item/Display
A
COPY : OC
B
COPY : RSPF
C
SCAN : OC
D
SCAN : RSPF
E
FAX : OC
F
FAX : RSPF
46-37
Purpose
Function (Purpose) Used to adjust the reproduction capability
Section
Operation/Procedure
1)
Select a target item with scroll keys on the touch panel.
2)
Enter the set value with 10-key.
3)
Press [EXECUTE] key.
4)
Press [YES] key.
This is to adjust the reproduction capability of red and yellow
Default
images when copying color documents with red and yellow images
value
in the monochrome mode.
0
Applied to the copy mode only.
Item/Display
A
R-Ratio
B
G-Ratio
B-Ratio
-
* B-Ratio: The value of gray making setting (B) is obtained from
-
the formula below.
1000-R-Ratio - G-Ratio
When [DEFAULT] key is pressed, the values are set to the initial
values (Default).
When the adjustment value of the adjustment item A is increased,
the copy density of red images is decreased. When the adjustment
value is decreased, the density is increased.
When the adjustment value of the adjustment item B is increased,
the copy density of yellow images is increased. When the adjust-
ment value is decreased, the density in also decreased.
Adjustment/Setup
density reproducibility in the monochrome
auto copy mode.
Content
Copy mode (for OC)
Copy mode (for RSPF)
Scanner mode (for OC)
Scanner mode (for RSPF)
FAX mode (for OC)
FAX mode (for RSPF)
Adjustment/Setup
of monochrome mode color.
Content
Gray making setting (R)
Gray making setting (G)
Gray making setting (B)
(1000-R-Ratio - G-Ratio)
Setting
Default
range
value
1 - 250
196
1 - 250
196
1 - 250
196
1 - 250
196
1 - 250
196
1 - 250
196
Setting
Default
range
value
0 - 1000
108
0 - 1000
678
Advertisement
