Sharp MX-M354N Installation Manual

Sharp MX-M354N Installation Manual

Multifunctional system
Hide thumbs Also See for MX-M354N:
Table of Contents

Advertisement

Transit, Installation (using) environment, Note
[1] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
(MAIN UNIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
(REVERSING SINGLE PASS FEEDER) . . . . . . . . 3-1
[4] MX-VR11 (DOCUMENT COVER). . . . . . . . . . . . . . 4-1
(500/2x500 SHEET PAPER DRAWER) . . . . . . . . . 5-1
[7] MX-FN23 (FINISHER) . . . . . . . . . . . . . . . . . . . . . . 7-1
[8] MX-TE10 (EXIT TRAY UNIT) . . . . . . . . . . . . . . . . . 8-1
[9] MX-TR11 (JOB SEPARATOR) . . . . . . . . . . . . . . . . 9-1
[11] MX-PK11 (PS3 EXPANSION KIT) . . . . . . . . . . . . .11-1
[12] MX-PF10 (BARCODE FONT KIT) . . . . . . . . . . . . 12-1
(NETWORK SCANNER EXPANSION KIT) . . . . . 13-1
[16] AR-SU1 (STAMP UNIT) . . . . . . . . . . . . . . . . . . . . 16-1
[17] MX-FR37U (DATA SECURITY KIT) . . . . . . . . . . . 17-1
(APPLICATION INTEGRATION MODULE) . . . . . 18-1
(APPLICATION COMMUNICATION MODULE) . . 19-1
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
INSTALLATION MANUAL
DIGITAL MULTIFUNCTIONAL
SYSTEM
MX-M264U/M314U/M354U
MX-M264N/M314N/M354N
MODEL
CONTENTS
[22] MX-KB14 (KEYBOARD) . . . . . . . . . . . . . . . . . . . . . 22-1
[23] Dehumidifying heater kit . . . . . . . . . . . . . . . . . . . . . 23-1
[24] IC card reader. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-1

SHARP CORPORATION

CODE: 00ZMXM264/I1E
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

Advertisement

Table of Contents
loading

Summary of Contents for Sharp MX-M354N

  • Page 1: Table Of Contents

    " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. This document has been published to be used SHARP CORPORATION for after sales service only. The contents are subject to change without notice.
  • Page 2 CONTENTS Transit, Installation (using) environment, Note [18] MX-AMX1 (APPLICATION INTEGRATION MODULE) 1. Installing (use) conditions ......i 1.
  • Page 3 Symbols in this manual The lists of symbols used in this manual are shown below. The meaning of each symbol described in the table must be understood for proper servicing. 1. Symbols used for notes and Symbol Meaning OK/GOOD Indicates a correct cautions procedure or result in an adjustment, etc.
  • Page 4 Symbol Meaning (Work content) Symbol Meaning (Work content) Cleaning Indicates that cleaning is Engage the pawl. (Vacuum) performed with a vacuum cleaner. Cleaning Indicates that cleaning is Screw lock Indicates that a screw is (Brush) performed with a brush. secured with adhesive. Indicates that oil is Unlock applied to lubricate.
  • Page 5: Transit, Installation (Using) Environment, Note

    Transit, Installation (using) environment, Note MX-M264U Service Manual * About a main unit illustration, it may differ from a target model. 1. Installing (use) conditions (3) Power frequency, waveform The frequency must be within the range of the specified frequency Before installing the machine, check that the following installing ±2%.
  • Page 6 F. Note for handling PWB and electronic parts Humidity RH When handling the PWB and the electronic parts, be sure to observe the following precautions in order to prevent against dam- age by static electricity. • When in transit or storing, put the parts in an anti-static bag or an anti-static case and do not touch them with bare hands.
  • Page 7: Transit And Delivery

    G. Note for proper drum, developing and fusing unit handling When handling the OPC drum and developing units, observe the following items. Drum unit • To prevent damage to the OPC drum, avoid working on the drum unit in high intensity light areas. •...
  • Page 8: Configuration

    MX-USA0 MX-UN01A MX-UN05A MX-UN10A MX-UN50A MX-UN1HA SHARPDESK 100 LICENSE Sharp OSA Network Scanner Sharp OSA Network Scanner Sharp OSA Network Scanner Sharp OSA Network Scanner Sharp OSA Network Scanner Tool 1 License Kit Tool 5 License Kit Tool 10 License Kit...
  • Page 9: Option List

    SHARPDESK 10 LICENSE KIT MX-US50 SHARPDESK 50 LICENSE KIT MX-USA0 SHARPDESK 100 LICENSE KIT MX-UN01A Sharp OSA Network Scanner Tool 1 License Kit MX-UN05A Sharp OSA Network Scanner Tool 5 License Kit MX-UN10A Sharp OSA Network Scanner Tool 10 License Kit MX-UN50A...
  • Page 10: Mx-M264U/M314U/M354U/M264N/M314N/M354N (Main Unit)

    [2] MX-M264U/M314U/M354U/M264N/M314N/M354N (MAIN UNIT) MX-M264U Service Manual C. Packed items check Unpacking A. Unpacking Name Quantity Operation manual D. Lock release (1) Tray rotation plate lock release Pull out the tray. Turn the fixing material and remove it. B. Fixing tape and protection material removal Remove the caution label.
  • Page 11: Installation

    Installation B. Set the control level for the reference toner density NOTE: When an optional paper feed desk is connected to the machine, unpack and install the paper feed desk, then NOTE: Setting of the reference toner density control level must be unpack the machine.
  • Page 12 C. Paper feed tray setup (1) System setting Press the [SYSTEM SETTINGS] key. Touch the [Paper Tray Settings] key. Touch the [Paper Tray Settings] key to configure the settings. These settings specify the paper type, paper size, and func- tions allowed for each paper tray. When the [Tray Settings] key is touched, a list appears showing the trays and the current settings.
  • Page 13: Mx-Rp15

    [3] MX-RP15 (REVERSING SINGLE PASS FEEDER) MX-M264U Service Manual B. RSPF unit attachment Unpacking Attach the RSPF unit to the main unit. A. Packed items check Name Quantity RSPF unit SPF glass unit Installation NOTE: Before installation, be sure to turn both the operation and Remove the rear upper cabinet cover.
  • Page 14: Mx-Vr11 (Document Cover)

    [4] MX-VR11 (DOCUMENT COVER) MX-M264U Service Manual Unpacking A. Packed items check Name Quantity Document cover unit Installation NOTE: Before installation, be sure to turn both the operation and main power switches off and disconnect the power plug from the power outlet. Make double sure that the data lamp on the operation panel does not light up or blink when per- forming installation.
  • Page 15: Mx-De17/De18 (500/2X500 Sheet Paper Drawer)

    [5] MX-DE17/DE18 (500/2x500 SHEET PAPER DRAWER) MX-M264U Service Manual Unpacking Turn off the main switch of the copier and then remove the power plug of the copier from the outlet. A. Remove the rear cover from the copier Remove the two screws and then remove the rear cover from the copier.
  • Page 16 D. Attach the copier E. Connect the harness Place the copier on the optional paper feed unit and remove Connect the cassette interface harness contained in the the second and third paper trays. optional paper feed unit to the paper feed unit interface PWB. Connect the copier to the paper feed unit using four fixing For two tray type plates and two screws (M4 x 12) for each plate.
  • Page 17 G. Remove the securing fixture for packing the J. Check for center displacement paper feed unit and remove the packing • Set an original on the document glass and copy it using the material paper tray in the copier. Then, copy an original using the attached optional paper feed Remove the securing fixture for packing that fixes the paper unit.
  • Page 18: Mx-Ds16/Ds17 (Low Stand/High Stand)

    [6] MX-DS16/DS17 (LOW STAND/HIGH STAND) MX-M264U Service Manual Installation Unpacking Attach the adjusters. Unpack the package, and check to confirm that all the parts are Attach the front adjusters (2 pcs.) as shown in the figure below. provided. Front Machine stand Packed parts add adjuster ( 110)
  • Page 19 Put the copier (or the paper feed unit) on the desk. Connect the copier (or the paper feed unit) and the desk with two screws (P tight) and two screws (S tight) packed together Insert the positioning pins (2 pcs.) of the desk into the position- with the copier.
  • Page 20: Mx-Fn23 (Finisher)

    [7] MX-FN23 (FINISHER) MX-M264U Service Manual Installation Unpacking NOTE: Turn off the main switch of the machine and then remove the power plug of the machine from the outlet. Open the front cover. MEMO: When removing the finisher, put your hand beneath the unit and lift it up as shown below.
  • Page 21 Insert the tray paper presence detection harness into the Open the manual feed tray and the right door. dummy connector on the fan duct. Remove the two screws, and remove the right cabinet. Disengage the pawls in the sequence of (1) and (2) and remove the paper exit dummy cover.
  • Page 22 11) Install the rear cabinet to the original position, and fix it with 15) Engage the finisher connection plate with the notch in the stay screw. at the right bottom of the machine. Slide the connection plate to the bottom, and attach M3 screw as shown.
  • Page 23 18) Press the finisher from the front to slide to the rear together 22) Install the left cabinet to the original position. with the connection plate. 19) Fix the connection plate from the front with the M3 screw which are packed with the finisher. 23) Install the finisher front cover from the left side by sliding, and fix the center of the fulcrum point with the resin clip.
  • Page 24 26) Connect the machine connection connector. Non LPS Do not connect to devices other than specified peripheral devices of our company. 27) Attach the staple position label to the document feed unit. MX-M264U MX-FN23 (FINISHER) 7 – 5...
  • Page 25: Mx-Te10 (Exit Tray Unit)

    [8] MX-TE10 (EXIT TRAY UNIT) MX-M264U Service Manual Parts included Remove two screws and remove the right cabinet unit. NOTE: One of the removed screws is used in the step 6). Paper exit unit Paper exit tray Paper holding arm Harness cover OP Paper exit Right paper...
  • Page 26 Wiring 10) Remove the screw and remove the paper exit fan connector sheet. 11) Install the harness cover OP and tightening the screw. Install the paper exit right cover sub and tightening the screw. 3 x 4 screw (S) 2PCS Install the right paper exit actuator and the paper holding arm.
  • Page 27: Mx-Tr11 (Job Separator)

    [9] MX-TR11 (JOB SEPARATOR) MX-M264U Service Manual Parts included Remove the right cabinet AS. M4 x 10 P tight (2pcs) Second paper Job separator unit Second paper exit unit exit tray holder M4 x 10 (5 pcs.) Mylar *Not used. Installation Install the second paper exit UN.
  • Page 28 Remove the paper holding arm, install it to job separator AS. 12) Install the rear cabinet. (Same as the current state) Paper holding arm Install the second paper exit tray holder. (New part) 13) Job separator setting in simulation 26-1. M4 P tight tightening Install the job separator tray AS.
  • Page 29: Mx-Pb15 (Printer Expansion Kit)

    [10] MX-PB15 (PRINTER EXPANSION KIT) MX-M264U Service Manual Unpacking A. Packed items check Name Quantity CD-ROM Operation manual Installation A. Enable setting of functions Enter the product key to enable the functions. Enter the system setting mode. The machine enters the product key input mode. Enter the product key.
  • Page 30: Mx-Pb15 (Printer Expansion Kit)

    [11] MX-PK11 (PS3 EXPANSION KIT) MX-M264U Service Manual Unpacking A. Packed items check Name Quantity CD-ROM (For Screen Font) Product key sheet Installation NOTE: To install the MX-PK11 (PS3 EXPANSION KIT), the MX- PB15 (PRINTER EXPANSION KIT) is required. A. Enable setting of functions Enter the product key to enable the functions.
  • Page 31: Mx-Pf10 (Barcode Font Kit)

    [12] MX-PF10 (BARCODE FONT KIT) MX-M264U Service Manual Unpacking A. Packed items check Name Quantity CD-ROM Product key sheet Installation NOTE: To install the MX-PK11 (PS3 EXPANSION KIT), the MX- PB15 (PRINTER EXPANSION KIT) is required. A. Enable setting of functions Enter the product key to enable the functions.
  • Page 32: Mx-Nsx1

    [13] MX-NSX1 (NETWORK SCANNER EXPANSION KIT) MX-M264U Service Manual Unpacking A. Packed items check Name Quantity CD-ROM Operation manual Installation A. Enable setting of functions Enter the product key to enable the functions. Enter the system setting mode. The machine enters the product key input mode. Enter the product key.
  • Page 33: Mx-Fx11 (Facsimile Expansion Kit)

    [14] MX-FX11 (FACSIMILE EXPANSION KIT) MX-M264U Service Manual Unpacking Remove the left cabinet. A. Packed items check Germany Australia France B. I/F cable connection For othe destinations Pass the I/F cable through the hole in the frame to connect to the connector.
  • Page 34 C. Left cabinet and rear cabinet attachment E. Turn ON the power of the main unit Remove the notch in the left cabinet, and attach the left cabi- Connect the power plug of the machine to the power outlet, net. and turn ON the main power switch and the operation panel power switch.
  • Page 35: Mx-Fwx1 (Internet Fax Expansion Kit)

    [15] MX-FWX1 (INTERNET FAX EXPANSION KIT) MX-M264U Service Manual Unpacking A. Packed items check Name Quantity CD-ROM Product key sheet Installation NOTE: To install the MX-FR37/FR37U (DATA SECURITY KIT), the MX-HD12 (HARD DISK EXPANSION KIT) is required. NOTE: In order to specify the address of the Internet Fax with the PC-FAX driver, the PC-FAX driver must be updated by the Internet Fax expansion kit.
  • Page 36: Ar-Su1 (Stamp Unit)

    [16] AR-SU1 (STAMP UNIT) MX-M264U Service Manual Unpacking Put the RSPF unit on a stable table with the OC mat upside. A. Packed items check Name Quantity Stamp unit B. Stamp unit attachment Stamp cartridge replacement procedure Open the OC mat. Stamp cartridge Installing screw *1: When replacing the stamp cartridge, Refer to “Stamp cartridge...
  • Page 37 D. Finish stamp cartridge attachment Install the sensor cover. Open the left cover, and open the document tray. Attach the finish stamp cartridge. Close the OC mat. E. Turn ON the power of the main unit Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch.
  • Page 38: Mx-Fr37U (Data Security Kit)

    [17] MX-FR37U (DATA SECURITY KIT) MX-M264U Service Manual Unpacking Remove the shield plate. A. Packed items check Name Quantity Program ROM Product key sheet User manual (CD-ROM) Installation NOTE: To install the MX-FR37U (DATA SECURITY KIT), the MX- HD12 (HARD DISK EXPANSION KIT) is required. NOTE: Before installing the data security kit, be sure to perform B.
  • Page 39 C. Shield plate and rear cabinet attachment Attach the shield plate. Attach the rear cabinet. D. Turn ON the power of the main unit Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch.
  • Page 40: Mx-Amx1

    [18] MX-AMX1 (APPLICATION INTEGRATION MODULE) MX-M264U Service Manual Unpacking A. Packed items check Name Quantity CD-ROM MX-AMX1 GETTING STARTED GUIDE Sharpdesk license kit Operation Manual Installation A. Enable setting of functions Enter the product key to enable the functions. Enter the system setting mode. The machine enters the product key input mode.
  • Page 41: Mx-Amx2

    [19] MX-AMX2 (APPLICATION COMMUNICATION MODULE) MX-M264U Service Manual Unpacking A. Packed items check Name Quantity CD-ROM Operation manual Installation A. Enable setting of functions Enter the product key to enable the functions. Enter the system setting mode. The machine enters the product key input mode. Enter the product key.
  • Page 42: Mx-Amx3 (External Account Module)

    [20] MX-AMX3 (EXTERNAL ACCOUNT MODULE) MX-M264U Service Manual Unpacking A. Packed items check Name Quantity CD-ROM Operation manual Installation A. Enable setting of functions Enter the product key to enable the functions. Enter the system setting mode. The machine enters the product key input mode. Enter the product key.
  • Page 43: Mx-Hd12 (Hard Disk Expansion Kit)

    [21] MX-HD12 (HARD DISK EXPANSION KIT) MX-M264U Service Manual Installation Unpacking NOTE: Before installation, be sure to turn both the operation and A. Packed items check main power switches off and disconnect the power plug from the power outlet. Make double sure that the data lamp on the operation panel does not light up or blink when per- forming installation.
  • Page 44 B. MFP PWB unit removal D. MFP PWB unit attachment Disconnect the connector and remove the MFP PWB unit. Attach the MFP PWB unit and connect the connector. C. HDD attachment E. Replace the SD card Remove the HDD from the HDD mounting plate. Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch.
  • Page 45: User Data Restore

    Turn ON the main power switch and the operation panel power Attach the rear cabinet. switch. Check to confirm that the machine is booted normally. Check to confirm that the E7-03 error does not occur. Wait until the display of "Wait for a while" disappears. NOTE: While "Wait for a while"...
  • Page 46: Mx-Kb14 (Keyboard)

    [22] MX-KB14 (KEYBOARD) MX-M264U Service Manual Unpacking Remove the operation panel base plate B from the operation panel base plate A. A. Check the packed items MEMO: When attaching the keyboard, the operation panel base plate B is not used. Name Quantity Keyboard unit...
  • Page 47 E. External fixture attachment Attach the keyboard unit and fix it with the fixing screw (M4 x 8 S-tight, M3 x 8 S-tight). Attach the operation panel base plate. Connect the connector. NOTE: Attach the keyboard unit so that the flat cable is above the keyboard unit.
  • Page 48: Dehumidifying Heater Kit

    [23] Dehumidifying heater kit MX-M264U Service Manual Parts list Kit name Kit code Part name Part code Q'ty Remarks Heater electric DKIT-0425FCZZ Dehumidifier heater control switch QSW-C9294QCZZ component kit Dehumidifier heater control switch label TLABZ5256FCZZ Supporter LSUPP0140FCPZ 3 本のみ使用 WH PWB CPWBF1935FCE1 WH harness DHAI-4701FCPZ...
  • Page 49: Installation

    Installation (2) WH PWB attachment Attach the supporter, and attach the WH PWB. NOTE: Before installation, be sure to turn both the operation and main power switches off and disconnect the power plug from the power outlet. Make double sure that the data lamp on the operation panel does not light up or blink when per- forming installation.
  • Page 50 B. Scanner heater kit installation (4) External fixture attachment Attach the paper exit tray (1) Scanner heater unit assembly Secure the marking position on the harness of the scanner heater to the heater fixing plate with the banding band. Attach the left cabinet. Extend the harness, and secure the other position of it with banding band.
  • Page 51 (2) Table glass removal Attach the scanner heater and secure it with the screw (M4 x 6 Bind machine screw). Pass the harness through the clamp. Remove the glass holder. Remove the table glass and the SPF glass. NOTE: The convex part of the scanner heater must be inserted into the hole of the scanner frame.
  • Page 52 (4) Table glass attachment Attach the SPF glass and the table glass. Attach the glass holder. NOTE: When installing the glass holder, slide it to the left until it clicks, and fix it with screws. C. Operation check after installation Turn on the dehumidifier heater switch.
  • Page 53: [24] Ic Card Reader

    [24] IC card reader MX-M264U Service Manual Installation Preparation NOTE: Before installation, be sure to turn both the operation and A. Supported IC card readers main power switches off and disconnect the power plug from the power outlet. Make double sure that the data lamp on the operation panel does not light up or blink when per- forming installation.
  • Page 54 B. Attachment to the IC card reader holder Attach the IC card reader to the IC card reader holder accord- ing to the attachment reference ribs. Attach the card reader fixing tape to the IC card reader holder referring to the notches as the reference. NOTE: The attachment reference position differs depending on the kind of the IC card reader.
  • Page 55 Holder type C Bind up the cables of the card reader. Y591-EHID-201 v01 NOTE: Cable length is differs depending on type of card (No reference position) reader, bind up the cable followed by the following instructions. Adjust the bind length of card reader cable and bind up it with banding band.
  • Page 56 F. System setting modification Attach the front cabinet upper. IC card reader device registration Device registration Enter the card reader setting menu as shown below. System Settings→Administrator Login→User Control→ Card Setting→Card Reader Device Registration Press [Read] button. Disconnect the connector which links the machine and the IC card reader, and then insert it back.
  • Page 57: Setting File For Hid Card Reading

    Setting file for HID card reading (2) Setting of the HID setting file A. Overview Section name Description Decoding\Facility Decode setting of the facility code. This manual describes the following setting procedures for reading Code (* If the facility code is not used, there is no need to data from an IC card by using the HID card reading function: describe this item.) •...
  • Page 58 D. Card reading test After importing the user area setting to the machine, a test can be executed to confirm that the cars is properly read. (* User control > Card area setting > Card reading test (* Only the system settings of the machine)) Execute "User control >...
  • Page 59: Remote Operation Panel Function Enable Setting

    [25] Remote operation panel function Enable setting MX-M264U Service Manual General To use the remote operation panel function, the password for the remote operation panel function must be entered on the password input menu displayed on the VNC boot screen. Note that, therefore, the password must be set in advance to use the remote operation panel function.
  • Page 60: Setting, Adjustments, Operation Check

    [26] Setting, Adjustments, Operation check MX-M264U Service Manual Firmware version check and version After installation of all the options to the machine, use SIM22-5 to check the version of each firmware. If it is not the latest version, upgrade it to the latest one. Function and operation check Check that the following operations are normal.
  • Page 61: [27] Setup And Adjustment Data Recording

    [27] Setup and adjustment data recording MX-M264U Service Manual Print the various setup data and the adjustment data (list) with SIM22-6 and keep the data. • In case of a memory trouble, if the data are not kept, all the adjustments must be made again.
  • Page 62: [28] Necessary Works Before Moving The Machine

    [28] Necessary works before moving the machine MX-M264U Service Manual Remove the following consumable parts from the machine. • Paper • Toner cartridges • Development cartridge Lock the following sections. • Scanner (Optical section) • Paper cassette lift plate NOTE: Since the hard disk drive is built in the machine, use care not to exert vibrations or shocks to the machine when in transit.
  • Page 63 LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: <Solder composition code of lead-free solder> Solder composition Solder composition code Solder composition...
  • Page 64 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
  • Page 65 Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated. • PCL is a registered trademark of the Hewlett-Packard Company. • Sharpdesk is a trademark of Sharp Corporation. • All other trademarks and copyrights are the property of their respective owners. SHARP CORPORATION...

This manual is also suitable for:

Mx-m314nMx-m264nMx-m354uMx-m314uMx-m264u

Table of Contents