Table of Contents
Advertisement
Figures
Figure 1: Front Panels of the x950 Switches ........................................................................................................................16
Figure 2: Rear Panel of the x950 Switches ..........................................................................................................................17
Figure 3: Link and Activity LEDs for Ports 1 to 24 ................................................................................................................21
Figure 4: Link and Activity LEDs for Ports 1 to 24 on the AT-x950-28XTQm Switch ...........................................................23
Figure 5: QSFP-4SFP10G-3CU and QSFP-4SFP10G-5CU Copper Breakout Cables........................................................24
Figure 6: ET3-MPO08-4LC-5 and ET3-MPO08-4LC-10 Fiber Optic Breakout Cables ........................................................25
Figure 7: LEDs for Ports 25 to 37 .........................................................................................................................................25
Figure 8: XEM2 Ethernet Line Cards....................................................................................................................................28
Figure 9: AT-XEM2-12XT Line Card.....................................................................................................................................30
Figure 10: AT-XEM2-12XTm Line Card................................................................................................................................32
Figure 11: AT-XEM2-12XS Line Card ..................................................................................................................................34
Figure 12: AT-XEM2-4QS Line Card ....................................................................................................................................36
Figure 13: AT-XEM2-1CQ Line Card....................................................................................................................................38
Figure 14: Management Panel .............................................................................................................................................40
Figure 15: Switch ID LED with the eco-friendly Mode Disabled ...........................................................................................43
Figure 16: Switch ID LED with the eco-friendly Mode Enabled ............................................................................................43
Figure 17: AT-PWR600 Power Supply .................................................................................................................................46
Figure 18: AT-FAN05 Fan Module........................................................................................................................................48
Figure 19: PORT Parameter in the Command Line Interface...............................................................................................49
Figure 20: Slot Numbers for Port Numbering on Stand-alone Switches...............................................................................50
Figure 21: Installation Options ..............................................................................................................................................59
Figure 22: Removing Accessories ........................................................................................................................................61
Figure 23: Removing the Shipping Box Partition ..................................................................................................................62
Figure 24: Lifting the Switch from the Shipping Box .............................................................................................................63
Figure 25: Removing the Switch from the Shipping End-caps and Protective Bag ..............................................................63
Figure 26: Accessory Kit.......................................................................................................................................................65
Figure 27: Removing the Power Cord and Documents from the AT-PWR600 AC Power Supply........................................67
Figure 28: Removing the Partition from the AT-PWR600 AC Power Supply Shipping Box .................................................68
Figure 29: Removing the Power Supply from the Shipping Box...........................................................................................69
Figure 30: Removing the Power Supply from the Shipping End-caps and Protective Bag ..................................................69
Figure 31: Removing the Blank Power Supply Panel from Slot PSU B................................................................................73
Figure 32: Sliding the AT-PWR600 AC Power Supply into the Chassis...............................................................................74
Figure 33: Seating the Power Supply on the Internal Connector..........................................................................................75
Figure 34: Removing the Blank Line Card Cover .................................................................................................................76
Figure 35: Removing the Ethernet Line Card from the Anti-static Bag.................................................................................77
Figure 36: Sliding the Ethernet Line Card into the Slot.........................................................................................................77
Figure 37: Seating the Ethernet Line Card in the Expansion Slot ........................................................................................78
Figure 38: Tightening the Two Captive Screws on the Ethernet Line Card..........................................................................79
Figure 39: Parts of the Bumper Feet ....................................................................................................................................81
Figure 40: Holes for Bumper Feet ........................................................................................................................................82
Figure 41: Inserting the Rivet Housing into the Bumper Foot...............................................................................................82
Figure 42: Placing the Bumper Foot on a Base Corner Hole ...............................................................................................83
Figure 43: Inserting the Rivet into the Bumper Foot .............................................................................................................83
Figure 44: Bracket Holes on the Switch................................................................................................................................86
Figure 45: Switch Orientations in an Equipment Rack .........................................................................................................87
Figure 46: Removing the Bumper Feet.................................................................................................................................88
Figure 47: Attaching the Equipment Rack Brackets .............................................................................................................90
Figure 48: Installing the Switch in an Equipment Rack.........................................................................................................90
Figure 49: Positions of the Switch on the Wall .....................................................................................................................94
7
Advertisement
Table of Contents
