Knoll Antenna Telescope Installation Instructions Manual page 67

End Panels
Telescope End Panels for Dual Tables
Pattern Numbers Represented:
Telescope End Panel, YEP____
Parts List:
End Panel Connector Link (A)
Dovetail Linking Bracket (B)
End Panel Block (C)
End Panel Leg Brace, Right Hand (D)
End Panel Leg Brace, Left Hand (E)
NOTE: Handedness is determined as you
face the end of the desk base
Polyurethane Grip Tape (F)
¼-20 x .75" Flat Head Machine Screw (G)
¼-20 x 1.25" Flat Head Machine Screw (H)
¼-20 x .5" Black Flat Head Screw (I)
End Panel with Glides
Adjustable Dual Table (With Intermediate or End
Application Base)
Tools Needed:
Right-Angle Ratcheting Power
Driver with #3 Phillips Bit
STEPS
NOTE
: Before attaching an End Panel, the
adjustable dual table (with intermediate
or end application base) should be fully
assembled (see previous installation guide
pages).
The crossbar adjacent to the end panel
must be a "mid-crossbar" type, with
dovetail linking brackets already installed,
to accept connector links.
The connector link that came with
the table base will be too wide to
properly connect the End Panel to
the base and should be discarded
for this end-panel application.
1. Slide the (2) End Panel Connector Links
(A) down onto the linking brackets
previously attached to the crossbar.
Do not fasten from below yet.
2. Attach (2) Dovetail Linking Brackets (B)
to the predrilled holes in the center of
the end panel, using (2) ¼ -20 x .75" Flat
Head Machine Screws (G) per bracket.
©2021 Knoll Inc.
(A) 3AF4111*
(E) 3AF4112L* (F) 6AA4233
(I) 3AB4190
3. Attach (2) End Panel Blocks (C) to the
predrilled holes on the bottom of the
end panel, using (2) ¼-20 x 1.25" Flat
Head Machine Screws (H) per block.
4. Apply a strip of Polyurethane Grip Tape
(F) to the inside curved surface of both
the Right-Hand End Panel Leg Brace (D)
and Left-Hand End Panel Leg Brace (E).
5. Place the End Panel in position,
located so that the Dovetail Linking
Brackets (B) are in line with the
End Panel Connector Links (A).
6. Position the Right-Hand End Panel Leg
Brace (D), just above the corresponding
End Panel Block (B) on the End Panel
with the curved (taped) surface against
the inner (toward the other column)
surface of the column. Slide the
brace down to engage the End Panel
Block (B), and attach using a ¼-20
x .5", Black Flat Head Screw (I). 3
(B) 3AF4009 (C) 3AF4114
(G) 7418440
7. Repeat step 6 for the Left-
Hand End Panel Brace (D).
8. Raise both End Panel Connector Links
(E) off the linking brackets on the
crossbar, and reposition them as to
engage both sets of Dovetail Linking
Brackets (B), i.e.: the brackets on the
crossbar and on the End Panel.
9. Extend the glides in the End Panel to
level the panel so that the End Panel
Connector Links (E) rest on the bottom
flanges of both pairs of Dovetail Linking
Brackets (B). Fasten the connector links to
the linking brackets with ¼ - 20 x .75" flat
head machine screws (G), from below.
Antenna Telescope Installation Instructions
END PA NELS 67
(D) 3AF4112R* (D)
(H) 7197100