Knoll Antenna Telescope Installation Instructions Manual page 61

Telescope Y-Base Adjustable Height Tables
Pattern Numbers Represented:
Telescope Y-Base Table, Rectangular,
Height-Adjustable Standard Electric, YKTS_ _YES_ _
Telescope Y-Base Table, Track,
Height-Adjustable Standard Electric, YKTT_ _ YES_ _
Telescope Y-Base Table, Bullet,
Height-Adjustable Standard Electric, YKTB_ _ YES_ _
Parts List:
Glide Assembly (A)
Square Tube End Cap (B)
Housing Cover (C)
Transformer Shelf (D)
Top Support Bracket, Left Hand (E)
Top Support Bracket, Right Hand (F)
Cable Clip (G)
/ -18 x 1.5" Hex Socket Cap Screw (H)
5
16
¼-20 x ¾" Flat Head Machine Screw (I)
¼-20 x / " Flat Head Machine Screw (J)
5
8
/ – 18 x 2.25" Flat Head Machine Screw (K)
5
16
10-24 x ¾" Flat Head Machine Screw (L)
#14 x 1" Flat Head Wood Screw (M)
#6 x / " Wood Screw (N)
5
8
Column Leg Assembly
Hub Weldment
Spoke
Dual Base Stretcher
Handset Control
iDrive Cable Kit
Power Supply w/ Splitter: KR3AF5045
Power Cord
Splitter: KR3AF5044
Table Top, Veneer or Laminate
P Clamp Kit
Tools Needed:
Power Driver
Phillips #2, #3 and #4 Bits
¼" Allen Wrench / Hex Bit and Ratchet
Rubber Mallet
STEPS
PREPARE LEGS
1. Attach a Hub Weldment to the bottom of
each Column Leg Assembly with (3) 5/16-18
x 1.5" Hex Socket Machine Screw (H) each.
2. Affix (2) Spokes to the two outboard arms
of each Hub Weldment, and position (1)
Dual Base Stretcher on the remaining arms,
connecting the column leg assemblies.
Attach the spokes and stretcher using (2)
¼-20 x ¾" flat head machine screws (I) at
each connection point.
©2021 Knoll Inc.
(A) 3AB4242
(D) 3AF4002
(G) 3AF4070
(J) 7189140
(M) 7491140
3. Install a Glide Assembly (A) into the bottom
of each spoke.
4. Insert an end cap (B) into the end of each
spoke, using a rubber mallet to ensure the
cap is inserted fully.
5. Attach a Top Support Bracket, Left Hand
(E), and a Top Support Bracket, Right Hand
(F) to the long sides of each housing, using
(2) 5/16 – 18 x 2.25" Phillips head machine
screws (K) per bracket.
Y- BASE AD JUSTABLE- HEIGHT BASES
(B) 3AB9008 (C) 3AF4003
(E) 3AF4100L (F) 3AF4100R
(H) 4A22202 (I) 7418440
(K) 3AF4089 (L) 4A21722
(N) 7528496
6. Attach a Housing Cover (C) to the outboard
end of each housing, using (2) ¼-20 x 5/8"
flat head machine screws (J) per cover.
7. Attach a Transformer Shelf (D) to the inboard
side of each housing, using (2) ¼-20 x 5/8"
flat head machine screws (J) per shelf.
8. Attach a Cable Clip (G) beneath each Top
Support Bracket (E/F) using (1) 10-24 x ¾"
Flat Head Machine Screw (L) per clip.
Antenna Telescope Installation Instructions
61