Advertisement
Quick Links
k.
base
™
Grounded
outlet
Grounding
pin
These instructions are suitable for Knoll k.base KBCE(X) A series frame assemblies and KHATT series worksurfaces or similar
© Knoll, Inc.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed, including
the following:
Read all instructions before using this product.
DANGER – To reduce the risk of electric shock:
1. Always unplug this furnishing from the electrical outlet before cleaning.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking off parts.
2. Close supervision is necessary when this product is used by, or near children, invalids, or
disabled persons.
3. Use this product only for its intended use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
4. Never operate this product if it has a damaged cord or plug, if it is not working properly,
if it has been dropped or damaged, or dropped into water. Return the product to a ser-
vice center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any opening.
8. Do not use outdoors.
9. Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
10. Max Load Ratings - "Max 250 lbs. load"
11. ELECTRICAL RATINGS: 100-120VAC, 60Hz, 4.2A at duty cycle 2 min/18 min
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS:
This product is for use on a nominal 120-volt circuit and has
a grounding plug that looks like the plug illustrated below.
Make sure that the product is connected to an outlet having
the same configuration as the plug. No adapter should be
used with this product.
Installation Instructions
1 of 9
Advertisement
Related Manuals for Knoll k. base
Summary of Contents for Knoll k. base
- Page 1 Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Grounding These instructions are suitable for Knoll k.base KBCE(X) A series frame assemblies and KHATT series worksurfaces or similar © Knoll, Inc. 1 of 9...
- Page 2 (rather than relying on the double stick tape, which can fall off) is recommended. Tools Phillips Screw Driver or Drill O — Hex NO IMPACT DRIVERS Wrench (Not Included) Step 1. Adjust the width of the frame assembly. A — Frame End x2 B — Crossbar (Pre-Installed) © Knoll, Inc. 2 of 9...
- Page 3 Step 2. Attach legs to the frame. C — Lifting Column x2 J— Countersunk Screw x8 P — Hex Wrench Tighten screws in an “X-Direction.” © Knoll, Inc. 3 of 9...
- Page 4 " from the back edge Note: Max allowable overhang is 15" L —Set Screws (Pre-Installed) M— Worksurface O — Hex Wrench Washer goes here between head and worksurfaces CAUTION NO IMPACT DRIVERS OR OTHER HIGH TORQUE EQUIPMENT ARE TO BE USED. © Knoll, Inc. 4 of 9...
-
Page 5: Step 4. Attach Feet
Step 4. Attach feet. D — Feet x2 I —Machine Screw x8 P — Hex Wrench Tighten screws in an “X-Direction.” © Knoll, Inc. 5 of 9... -
Page 6: Step 5. Install The Handset
Step 5. Install the handset. Digital Handset (“F”) can be mounted on the Left or Right Side. Left Side Right Side F — Programmable Digital Handset K — Wood Screw x2 © Knoll, Inc. 6 of 9... - Page 7 Step 6. Attach control box to underside of the worksurface. E — Control Box x1 K — Wood Screw x2 © Knoll, Inc. 7 of 9...
-
Page 8: Step 7. Attach Cables
Step 7. Attach cables. G — Leg Cable G — Leg Cable H — Power Cable H — Power Cable F — Programmable Digital Handset Note: Orient and install Control Box to avoid G — Leg Cable “F” bending cables. “G” “G” Step 8. Carefully flip the table over. © Knoll, Inc. 8 of 9... -
Page 9: Step 9. Set Up Handset
Do not sit or stand on the desk frame. Do not crawl or lie Specs under the desk frame. k. base Adjustable Height Standing Desk — Frame Only Do not open or modify any of the components, including the Lifting Columns, Control Box, or Handset. Doing so risks Frame width min/max: 36"–64"...