Knoll Antenna Telescope Installation Instructions Manual page 60

Telescope Return Bases
PREPARE THE RETURN TOP
10. Attach the (2) Main to Return Tie "W"
Brackets (F) to the end of the return top
using (2) ¼-14 x 7/8" pan head machine
screws (M), per bracket, into the pilot
holes.
Note: The midline of the "W" bracket is
intentionally inset from the edge of the
return top.
POSITION THE RETURN ASSEMBLY
11. Set the primary structure to a height
similar to the return structure (typically its
lowest position), and place the Return Rail
Hook Top Bracket (G) over the primary
structure's front rail. The primary table
desk top will need to be loosened to allow
the hook to be installed. Prop or have
someone hold the shorter rail as needed,
and continue.
12. Verify that the return structure is in the
appropriate location for the depth of the
return top, then secure the rail bracket in
place by attaching a Return Rail Clamp
Bottom Bracket (H) with (1) ¼ -20 X 1"
machine screw (K).
Note: The return column is always
centered on the return top depth.
13. Attach the End Cap with Support Tab (I)
to the underside of the primary top with a
#14 x 1" flat head wood screw (L).
©2021 Knoll Inc.
INSTALL THE RETURN TOP
Note: As the rail clamp assembly and
end cap are only pressed into the ends of
the rails, install the tops immediately. DO
NOT attempt to move the station until tops
are in place and the return structure is
completely fastened.
14. Lay the return top on the return base
assembly, sliding the "W" brackets (F)
under the primary top. Be sure to not
disengage the rail clamp assembly (G/H)
from the end of the return rail. Place a
Spacer (P) between the top of each rail
and the underside of the top, centered on
the width of the top. Spacers are attached
to the top using (1) #12 X ¾" flat head
black wood screw (Q) per spacer.
15. Attach return top to base using (4) #14 x
1" flat head wood screws (L) per cradle.
16. Secure the "W" brackets (F) to the
primary top using (2) ¼-14 x 7/8" pan
head wood screws (M), per bracket.
ATTACH THE RETURN ELECTRICAL
COMPONENTS
Note: For optimal performance, the power
supply must connect into the middle leg
in a 3-leg configuration. This will require
three ports at the middle leg; use two
splitters to achieve this.
17. At the leg where the Return attaches
(middle leg) plug two (2) splitters into
the housing outlets and place the power
supply onto the transformer shelf.
Connect the two iDrive cables from each
other leg and the power supply to three of
the four splitter ports.
18. Using (2) #6 x 5/8" wood screws (S)
mount the Handset Control Switch to the
underside of the return top or the primary
top, at the front edge.
RE TUR N BASES
PERFORM A RESET FOR THE THREE
COLUMNS IN EACH STATION
19. Apply approximately 100 lbs of weight to
the station. Press and hold both UP and
DOWN buttons for ten seconds. After
releasing the buttons, press and hold the
DOWN BUTTON until all three columns
bottom out. Press the UP button and the
station will be ready to perform normally.
Remove the weight. Run the station all the
way up and down again to ensure there
are no issues with the columns.
LEVEL TABLES
20. Place the tables in their final positions and
level by extending the leveling glides as
needed.
21. When levelers are extended more than ½",
install the Helical Glide Shroud. See
Helical Glide Installation Instructions.
INSTALL POWER STRIP ACCESSORY
(WHERE APPLICABLE)
See Power Strip Installation Instructions.
INSTALL CLEAT PLATE & CLEAT PLATE
COVER ACCESSORIES (WHERE
APPLICABLE)
See Cleat Plate and Cleat Plate Cover
Installation Instructions.
Antenna Telescope Installation Instructions
60