Download Print this page
Knoll Hipso Assembly Instructions Manual

Knoll Hipso Assembly Instructions Manual

Height-adjustable desk
Hide thumbs Also See for Hipso:

Advertisement

Quick Links

Hipso
Height-Adjustable Desk
Assembly Instructions
Thanks for choosing a Hipso Desk! Be sure to follow these assembly instructions.
To begin, you will build the base. Next, you will add the worksurface.
Finally, you will power the desk.
For step-by-step video
instructions, visit knoll.com
Knoll, Inc.
1235 Water Street
East Greenville, PA 18041

Advertisement

loading
Need help?

Need help?

Do you have a question about the Hipso and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Knoll Hipso

  • Page 1 Height-Adjustable Desk ™ Assembly Instructions Thanks for choosing a Hipso Desk! Be sure to follow these assembly instructions. To begin, you will build the base. Next, you will add the worksurface. Finally, you will power the desk. For step-by-step video instructions, visit knoll.com...
  • Page 2 • #2 Phillips Head Screwdriver Handset recommended • #3 Phillips Head Screwdriver recommended • Blanket or Other Floor Protection required • A Friend required Feet Side Brackets Adjustable Crossbars (shown facing opposite directions) © Knoll, Inc. Page 2 of 12...
  • Page 3 • For a 57" wide top extend each crossbar to 52 " long Helpful hint: This step is especially important for 45" wide Loosen set screws tops. Below is a guide to identifying " on a tape measure. " Required: Small Allen Wrench © Knoll, Inc. Page 3 of 12...
  • Page 4 Set screw feel like the screw is going in crooked, remove the screw and start again. Required: Large Allen Wrench (4) Screw Socket Flat Head M8 x 16 ZN © Knoll, Inc. Page 4 of 12...
  • Page 5 Required: #3 Phillips Head Screwdriver or the Offset Screwdriver. (4) ¼-20 x Under-cut Flathead, 100 degree screws #3 Phillips Head You are about halfway done! © Knoll, Inc. Page 5 of 12...
  • Page 6 Move your base to the side but keep it nearby while you can get the top situated. You’ll need it in the next step. © Knoll, Inc. Page 6 of 12...
  • Page 7 Helpful Hint: You can loosen the set screws to readjust the width of your base if you find the holes are not lining up properly. Be sure to tighten the set screws when you're done. Handset holes / front of worksurface © Knoll, Inc. Page 7 of 12...
  • Page 8 13. Attach the side brackets to the worksurface using four (4) #10 x 1" wood screws (D). Required: #2 Phillips Head Screwdriver or the Offset Screwdriver. (4) 10 x 1" wood screws #2 Phillips Head © Knoll, Inc. Page 8 of 12...
  • Page 9 45"-wide top. The 51"-wide top will use an additional two (2) #10 x 2½" wood screws (E). A 57"-wide top will use an additional four (4) #10 x 2½" wood screws (E). © Knoll, Inc. Page 9 of 12...
  • Page 10 17. Secure the control box to the underside of the desk with the provided wood screws. The label will be visible when installed correctly. Required: #2 Phillips Head Screwdriver or the Offset Screwdriver Control box with provided wood screws © Knoll, Inc. Page 10 of 12...
  • Page 11 19. Before standing the table upright, use the P-Clips to manage electrical cables. Required: #2 Phillips Head Screwdriver or the Offset Screwdriver P-clips and screws Manage cables with Zip Ties and P-clips, provided © Knoll, Inc. Page 11 of 12...
  • Page 12 ™ 11. Carefully turn table right side up. Connect to power and perform a reset. To perform a reset, rmly press and hold the Up and Down Get ready to use your Hipso desk. ™ Button for 8 seconds then release and immediately press and hold the down button until the table travels to its lowest limit, stops mov- ing, and then moves up a little.