ADTRAN Total Access 850 System Manual page 104

Section 4 User Interface Guide
I (FXS) > C
NTERFACES
Sets the TX direction level points. This signal will change the volume of the voice. TX (dB) is the signal
that is transmitted out the T1, with 0 dB being the strongest. If the volume is too loud across the T1, this
number should be increased. A higher number indicates more attenuation which equals lower volume. The
value entered must be less than 10 dB. Default is
I (FXS) > C
NTERFACES
Sets the RX direction level points. This signal will change the volume of the voice. A higher number
indicates more attenuation which equals lower volume. The value entered must be less than 10 dB. Default
is . The maximum signal is
3.0 dB
I (FXS) > C
NTERFACES
Indicates whether the module is
been mapped. For proper operation, the port must be mapped using the
S .
ERVICE
I (FXS) > C
NTERFACES
Sets the line impedance. Choices are
. The line impedance of each port is based on the size of the network. Default is
A
UTO
I (FXS) > C
NTERFACES
This is better referred to as On-Hook Message Waiting. When this is set to
open, even in On-Hook conditions, in order for these FSK message tones to pass through. Default is
D . Enabling on-hook message waiting will allow message lamp usage but will cause a lower
ISABLE
on-hook voltage. Disabling this feature will allow higher on-hook voltage but will not allow on-hook
messaging other than caller ID.
I (FXS) > C
NTERFACES
Sets the port to use E&M signaling on the T-Span and either loop start or ground start supervision on the
analog 2-wire interface. To access submenus for this item, use the arrow keys to scroll to the
column for the corresponding module, and then press
I (FXS) > C
NTERFACES
Sets the port to either
L
I (FXS) > C
NTERFACES
Sets the supervision method used to either
I (FXS) > C
NTERFACES
Used to enable or disable the on-board dial tone generation. Dial Tone is supplied for 5 sec; then it drops.
It cannot be broken when dialing digits. Default is
I (FXS) > C
NTERFACES
Used to enable or disable the option of generating ring back tone towards the T-span. Default is
104
> T ( B)
d
ONFIG X
> R ( B)
d
ONFIG X
.
0.0 dB
> S M
ONFIG VC ODE
I S or
N ERVICE
> L Z
ONFIG INE
600
OHMS
> M I
ONFIG SG ND
> T
ONFIG ANDEM
> T
ONFIG ANDEM
or
S G
OOP TART ROUND
> T
ONFIG ANDEM
I
MMEDIATE
> T
ONFIG ANDEM
> T
ONFIG ANDEM
© 2004 ADTRAN, Inc.
.
6.0 dB
O S . This does not indicate whether the port has
UT OF VC
, 900 , 600
OHMS OHMS
.
<E >
NTER
> C M
ONVERSION ODE
mode. Default is
S
TART
> S
UPERVISION
or W . Default is
INK
> D T
IAL ONE
.
D
ISABLE
> R B
ING ACK
Total Access 850 System Manual
menu. Default is
DS0 M
APS
µ
+ 2.16 F, 900 + 2.16
OHMS
600
OHMS
talk path is always
E ,
NABLE
T
.
L S
OOP TART
I .
MMEDIATE
I
N
µ and
F,
.
ANDEM
D .
ISABLE
64203376L1-1B