YOKOGAWA WT1600FC User Manual page 41

Command
:IMPedance[:STATe]
:IMPedance:SUPerpose?
:IMPedance:SUPerpose:AMPLitude
:IMPedance:SUPerpose:DETaile?
:IMPedance:SUPerpose:DETaile:HOLD
:IMPedance:SUPerpose:DETaile:LIMit
:IMPedance:SUPerpose:DETaile:RATio
:IMPedance:SUPerpose:DETaile:WAVeform
:IMPedance:SUPerpose:FREQuency?
:IMPedance:SUPerpose:FREQuency:RANGe
:IMPedance:SUPerpose:FREQuency:VALue
:IMPedance:SUPerpose:OFFSet
:IMPedance:SUPerpose:OUTPut?
:IMPedance:SUPerpose:OUTPut[:STATe]
:IMPedance:SUPerpose:OUTPut:TYPE Sets the output type of the load current for impedance measurements or
:IMPedance:VOLTage?
:IMPedance:VOLTage:ESTimate?
:IMPedance:VOLTage:ESTimate[:ALL]
:IMPedance:VOLTage:ESTimate:ELEMent<x>
:IMPedance:VOLTage:INITialize
:IMPedance:VOLTage:MRANge?
:IMPedance:VOLTage:RANGe?
:IMPedance:VOLTage:RANGe[:ALL]
:IMPedance:VOLTage:RANGe:ELEMent<x>
IM 760151-17E
Function
Turns ON/OFF the impedance measurement mode or queries the
current setting.
Queries all settings related to the load current for impedance measurements. 5-43
Sets the amplitude of the load current for impedance measurements or
queries the current setting.
Queries all settings related to the detailed settings of the load current for
impedance measurements.
Sets the action taken by the WT1600FC (handling of the control signal to
the impedance measurement electronic load device) when hold is activated
or queries the current setting.
Sets the range of the load current for impedance measurements or queries
the current setting.
Sets the current value per volt of the control signal to the impedance
measurement electronic load device or queries the current setting.
Sets the waveform of the load current for impedance measurements or
queries the current setting.
Queries all settings related to the frequency of the load current for
impedance measurements.
Sets the frequency range of the load current for impedance measurements
or queries the current setting.
Sets the frequency of the load current for impedance measurements
or queries the current setting.
Sets the magnitude of the DC component of the load current for
impedance measurements or queries the current setting.
Queries all settings related to the output of the load current for
impedance measurements.
Turns ON/OFF the load current for impedance measurements or queries
the current setting.
queries the current setting.
Queries all settings related to the voltage sensing input of impedance
measurements.
Queries the impedance estimates of all impedance measurement elements. 5-44
Sets the impedance estimates of all impedance measurement elements
collectively.
Sets the impedance estimate of the impedance measurement element or
queries the current setting.
Sets the voltage range to the initial range.
Queries the present voltage measurement range.
Queries the voltage range mode of all impedance measurement elements.
Sets the voltage range mode of all impedance measurement elements
collectively.
Sets the voltage range mode of the impedance measurement element
or queries the current setting.
5.1 Command List
Page
5-43
5-43
5-43
5-43
5-43
5
5-43
5-43
5-43
5-44
5-44
5-44
5-44
5-44
5-44
5-44
5-44
5-45
5-45
5-45
5-45
5-45
5-45
5-5