Yamaha PM5D Owner's Manual page 191

FUNCTION PARAMETER 1
PAGE BACK
PAGE FORWARD
PAGE CHANGE
PAGE BOOKMARK
GEQ PARAM PAGE
EFFECT PARAM PAGE
LAYER SNAPSHOT
DIRECT RECALL/
MODE CHANGE
MUTE MASTER
NEXT BANK
USER DEFINED KEY
PREVIOUS BANK
BANK
DIRECT SELECT
MIDI NOTE
MIDI DIRECT OUT MIDI PGM CHANGE
MIDI CTRL CHANGE
SET LOCATION, RS-422
REC, RS-422 PLAY, RS-422
STOP, RS-422 FF, RS-422
REW, RS-422 LOCATE 1–20
MACHINE CONTROL
MMC REC, MMC PLAY, MMC
STOP, MMC FF, MMC REW,
MMC LOCATE 1–20
GPI OUT CONTROL PORT 1–12
PM5D EDITOR CON-
*5
TROL
*1. The corresponding channel will be selected in the DEFINE field of the MONITOR screen, and the monitor source will switch to
DEFINE.
*2. The LED will light for User Defined keys for which a screen has been memorized. The column in the right of the list in the USER
DEFINE screen shows the name of the memorized screen.
*3. Layers that can be memorized include the following items.
- The layer selected in the INPUT channel strip (CH 1-24, CH 25-48, MIDI REMOTE)
- The layer selected in the ST IN/FX RTN channel strip (ST IN 1-4, FX RTN 1-4, MIDI REMOTE)
- The layer shown by the DCA channel strip (DCA, A–F, GEQ)
- If the DCA channel strip is controlling GEQ, the GEQ module number and band
- The encoder mode selected by ENCODER MODE (SEND, PAN, HA, ATT, ALT)
- The FADER FLIP status
- The currently selected MIX send
- The mode selected in the MIX section (MIX SEND, MIX MASTER)
- The source selected in the METER section (CH 1-24 ST IN, CH 25-48 ST IN, MIX/MATRIX)
*4. The output port and MIDI channel can be specified in the MIDI SETUP screen.
*5. This parameter specifies the PM5D Editor window that you want to control. If the specified window is closed or inactive, the window
will be opened and made active. If the specified window is already open and active, the window will be closed. This function can be
selected if the system software supports PM5D Editor. For details on the most recent system software version, refer to the website.
http://www.yamahaproaudio.com
Note
During PREVIEW mode, the following USER DEFINE functions that affect internal signal processing are disabled;
EVENT LIST, TALKBACK ASSIGN, MONITOR, MIDI DIRECT OUT, MACHINE CONTROL, and GPI OUT CONTROL.
PARAMETER 2
—
GEQ 1–12
EFFECT 1–8
— —
LATCH
UNLATCH
—
BANK A–D
C-2–G 8
1–128
0–119
—
MMC ID= 1–127, ALL
LATCH
UNLATCH
*5
PM5D/PM5D-RH Owner's Manual
Explanation
Display the screen that you used immediately prior to the
current screen
Display the screen that you used immediately after the cur-
rent screen
Memorize the currently selected screen (hold down the key
for two seconds or longer), or display the last-memorized
screen (press and release the key within two seconds)
Display the GEQ PARAM screen
Display the EFFECT PARAM screen
Memorize the state of the layer assigned to the panel (hold
down the key for two seconds or longer), or display the last-
memorized layer (press and release the key within two sec-
*3
onds)
Switch the function of the SCENE MEMORY [1]–[8] keys
(DIRECT RECALL / MUTE MASTER) each time you press
the User Defined key
The SCENE MEMORY [1]–[8] keys will function as DIRECT
RECALL while you hold down the User Defined key
Switch to the next bank of User Defined key assignments
Switch to the previous bank of User Defined key assign-
ments
Switch to the desired bank of User Defined key assignments
When you press the key, transmit a note-on message with
the specified note number and a velocity of 127 When you
release the key, transmit a note-on message of the same
note number with a velocity of 0 (= note-off)
When you press the key, transmit a program change mes-
*4
sage with the specified number
When you press the key, transmit a control change message
with the specified control number and a value of 127 When
you release the key, transmit a control change message of
the same control number with a value of 0
Transmit the specified RS422/MMC command from the
RS422 REMOTE connector or the currently-valid MIDI port
(the SET LOCATION command is common to RS422 and
MMC)
Switch the specified GPI OUT port between active/inactive
each time you press the key
Switch the specified GPI OUT port to inactive while you hold
down the key
Switch windows in PM5D Editor on a PC
Reference section
*2
*4
*4
191