Panel Operation - Yamaha PM5D Owner's Manual

ALTERNATIVE . . . When you press the [CH 1-24]
or [CH 25-48] key, the opposite
layer will be shown by the
meters in the center of the panel
(if an input channel is selected
in the meter section). When you
press the [STIN 1-4] or
[FXRTN 1-4] key, the opposite
layer will be shown by the
meters in the upper right of the
panel.
Note
• If this is set to SAME or ALTERNATIVE, the meters in the
center of the panel and the meters in the upper right can be
switched independently.
• If the selected layer is switched from the panel, the layer
shown by the meters will also change. However if you switch
the METER SECTION field in the constantly-displayed area
in the upper part of the screen, the layer selected on the
panel will not change.
• FOLLOW MIX MASTER MODE
If this button is on, pressing the MIX section [MIX
MASTER] key will cause the meters in the center of the
panel and the meters in the upper right of the panel to
show the MIX/MATRIX channel levels. Press the MIX
section [MIX SEND] key to return to the original input
channel level display.
5
E PANEL OPERATION
Here you can set the following options for panel
operation.
• AUTO CHANNEL SELECT
This specifies whether the corresponding channel will
be selected when you operate a channel's [ON] key,
fader, or encoder. INPUT CH (input channels) and
OUTPUT CH (output channels) can be turned on/off
separately.
• AUTO DISPLAY
For each of the following items, you can individually
specify whether the related screen will automatically
appear when you use the SELECTED CHANNEL sec-
tion to operate a specific parameter. The following
table shows the parameters corresponding to each but-
ton and the screen that will appear.
Button name
HA
PHASE/ATT
EQUALIZER
DYNAMICS
DELAY
DCA/MUTE/
SAFE
TO MIX/STE-
REO
TO MATRIX
6 7
OUTPUT
MASTER
• MAKE PAIR ON PANEL
If this button is on, you can use the [SEL] keys to set/
defeat pairing. In Horizontal Pair mode, you can set/
defeat pairing by simultaneously pressing the [SEL]
keys of two pairable channels. In Vertical Pair mode,
you can set/defeat pairing by holding down the
[SHIFT] key and pressing the [SEL] key of one of the
channels. (For more about pair modes ➥ p.45)
• DCA/MUTE FLASH INDICATE
If this button is on, the DCA [MUTE] key LED and the
DCA assign LED for channels belonging to that DCA
group will blink when you turn on a DCA [MUTE] key
(DCA section).
• MIX MINUS CONFIRMATION
If this button is on, a confirmation message will appear
when you execute the Mix Minus setting (hold down
the [SEL] key of an input channel and press the [SEL]
key of a MIX channel) from the panel.
• SCENE UP/DOWN KEY
This specifies what the SCENE MEMORY [π]/[†]
keys will do when pressed in the SCENE screen. You
can choose one of the following two operations.
SCENE +1/–1 . . . . . Pressing the SCENE MEMORY
PM5D/PM5D-RH Owner's Manual
Corresponding
Screen that appears
parameters
Input channel head INPUT HA/INSERT
amp gain function screens
Input channel INPUT EQ function ø/
phase/attenuator ATT screen
INPUT EQ/OUTPUT
EQ-related param-
EQ function EQ
eters
PARAM screen
INPUT GATE/COMP
function or OUTPUT
Gate/compressor-
COMP function GATE
related parameters
PARAM or COMP
PARAM screen
INPUT DELAY/OUT-
Delay-related
PUT DELAY function
parameters
screens
INPUT DCA/GROUP
function or OUTPUT
DCA/GROUP func-
DCA group / Mute
tion DCA GROUP
group / Recall safe-
ASSIGN, MUTE
related parameters
GROUP ASSIGN or
RECALL SAFE
screen
PAN/ROUTING func-
tion CH to MIX screen
TO MIX/TO STE-
or SURR PARAM
REO-related
screen, or MATRIX/ST
parameters
function MATRIX/ST
ROUTING screen
MATRIX/ST function
Send level to
MATRIX/ST ROUT-
MATRIX bus
ING screen
OUTPUT VIEW func-
MIX/MATRIX chan-
tion FADER VIEW
nel output level
screen
[π] key will select the next
highest-numbered scene, and
pressing the SCENE MEMORY
[†] key will select the next low-
est-numbered scene. (Key
presses will increment/decre-
ment the scene number.)
Reference section
187