Yamaha PM5D Owner's Manual page 184

MIDI REMOTE function
❏ Initiating communication between the
PM5D and the DME series unit
To select the port used for audio signal transmission/recep-
tion between the PM5D and the DME series unit, and to
initiate communication, proceed as follows.
Connect the PM5D and the DME series unit.
1
In the DISPLAY ACCESS section, press the
2
[MIDI/REMOTE] key several times to access the
DME CONTROL screen.
In the component selection area at the upper
3
left of the screen, select SETUP.
A screen like the following will appear.
1
3 4
The SETUP screen contains the following items.
A CONNECT
This button initiates or terminates the connection
between the PM5D and the DME series unit.
B MIDI PGM CHANGE (MIDI program
change)
If this button is on, a program change message will be
transmitted to the DME via the I/O card (MY16-C) or
via the CASCADE IN/OUT connectors when a scene is
recalled on the PM5D. This allows scenes to be recalled
on the DME in tandem with scene recall operations on
the PM5D.
C INPUT PORT
Here you can select the PM5D port that will receive
audio signals from the DME.
D MONITOR PORT
Here you can select the PM5D port that will receive
monitor signals from the DME. Since this monitor sig-
nal is sent to the PM5D's CUE bus, the DME's monitor
function can be controlled from the PM5D just like the
PM5D's own cue function (EXTERNAL CUE
function).
E MIXER SETUP (show the MIXER SETUP
screen)
This button displays the SYS/W.CLOCK function
MIXER SETUP screen.
F OUTPUT PORT
Here you can select the PM5D port that will output
audio signals to the DME.
184
PM5D/PM5D-RH Owner's Manual
2
5
6
Reference section
In the INPUT PORT area
4
located at the lower left
of the screen, select the
PM5D port that will
receive audio signals from
the DME series unit.
The types of port that can be
selected here will depend on
the port that is currently selected for cascade input
(MIXER SETUP screen CASCADE IN PORT SELECT
field), as follows.
Setting in the CAS-
CADE IN PORT Items available in the INPUT
SELECT field (MIXER PORT field
SETUP screen)
CASCADE IN ----, SLOT1–SLOT4
SLOT4 ----, CASCADE IN, SLOT1–SLOT3
SLOT3/4 ----, CASCADE IN, SLOT1–SLOT2
SLOT1-4 [CH1-8] ----, CASCADE IN
SLOT1-4 [CH9-16] ----, CASCADE IN
Note
You cannot switch the cascade input port setting from the
DME CONTROL screen. If necessary, click the MIXER
SETUP button to access the MIXER SETUP screen (SYS/
W.CLOCK function), and change the port you will use for cas-
cade input.
In the MONITOR PORT field, select the PM5D
5
port that will receive monitor signals from the
DME series unit.
The following ports can be selected.
---- . . . . . . . . . . . . . . . . . .No assignment
SLOT1-1–SLOT4-16 . . .The desired port of slot 1–4
CASCADE 1–32 . . . . . . .CASCADE IN ports 1–32
In the OUTPUT PORT field
6
located in the lower right
of the screen, select the
PM5D port that will trans-
mit audio signals to the
DME.
The types of port that can be
selected here will depend on
the port that is currently selected for cascade output
(MIXER SETUP screen CASCADE OUT PORT
SELECT field), as follows.
Setting in the CAS-
CADE OUT PORT Items available in the OUTPUT
SELECT field (MIXER PORT field
SETUP screen)
CASCADE OUT ----, SLOT1–SLOT4
SLOT3/4
----, SLOT1–SLOT4, CASCADE
SLOT1-4 [CH1-8]
OUT
SLOT1-4 [CH9-16]
Note
You cannot switch the cascade output port setting from the
DME CONTROL screen. If necessary, click the MIXER
SETUP button to access the MIXER SETUP screen (SYS/
W.CLOCK function), and change the port you will use for cas-
cade output.