Yamaha PM5D Owner's Manual page 176

MIDI REMOTE function
5
D BANK SELECT
Of the four banks, select the bank for which you want
to make settings. When you use the A–D buttons to
select a bank, the name of that bank will be displayed in
the field immediately above. You can click the
ton at the left to edit the name of the bank.
E CLEAR BANK
This button erases the currently selected bank (all
MIDI messages will be deleted).
6
8
F MIDI message
From the top, these fields assign MIDI messages to the
ENCODER [ON] keys, encoders, CH [ON] keys, and
faders. Click the to open the MIDI REMOTE
SETUP window, and input the message as hexadeci-
mal values. You can input the following values.
Available
Value
Assignments
00(H)–
All
FF(H)
END All
SW All
ENCODER
ENC ON/
ENCODER
CH ON/
FAD
FADER
Hint
When you click a hexadecimal value, the region interpreted as
a MIDI message that includes that value will be displayed in
red.
176
PM5D/PM5D-RH Owner's Manual
4
but-
7
Content
The MIDI message that is trans-
mitted (hexadecimal).
Indicates the end of the MIDI
message. When you operate the
corresponding controller, the
MIDI message from the begin-
ning until immediately before
END will be transmitted.
Indicates the on/off status of the
encoder [ON] key or the channel
[ON] key. A value of 7F(H) is
transmitted when the key turns
on, and a value of 00(H) is trans-
mitted when the key turns off. If
this is assigned to an ENCODER
or FADER, the current value of
the key will be transmitted when
the encoder or fader is operated.
Indicates the current position of
the encoder. If assigned to an
ENCODER, a value of 00–7F(H)
is transmitted when the encoder
is operated. If assigned to an
ENCODER [ON] key, the current
value of the encoder is transmit-
ted when the key is switched on.
Indicates the current position of
the fader. If assigned to a
FADER, a value of 00–7F(H) is
transmitted when the fader is
operated. If assigned to a CH
[ON] key, the current value of the
fader is transmitted when the key
is switched on.
Reference section
G LEARN
Use this button to assign a received MIDI message to a
controller. When you turn on one of the four LEARN
buttons, the MIDI message received by the PM5D will
be assigned to the corresponding controller. The
LEARN function uses the MIDI messages received at
the input port specified by the MIDI REMOTE OUT-
PUT PORT in the MIDI SETUP screen.
Hint
• MIDI messages assigned using the LEARN button can be a
maximum of 16 bytes long (the 17th and subsequent bytes
are discarded). If the message is less than 16 bytes long,
END will be immediately after the last data value.
• If a control change is received, the third byte will automati-
cally be replaced by FAD (if the assignment destination is
FADER), ENC (if the assignment destination is ENCODER),
or SW (if the assignment destination is ENCODER ON or
CH ON).
• If more than one message is received while a LEARN but-
ton is on, the last message will be used. (If the status byte
was omitted from the last message, the appropriate status
byte will be added.)
H LATCH
If a specific byte is set to "SW" in a message assigned to
an ENCODER [ON] key or CH [ON] key, use the
LATCH button to select one of the following
behaviors.
• If the LATCH button is on
The on/off status will change each time you press the
key (Latched). If you press the key from the Off state, a
MIDI message with 7F(H) as the SW value will be
transmitted, and when you press the same key once
again a MIDI message with 00(H) as the SW value will
be transmitted.
• If the LATCH button is off
The switch will be on only while you are holding it
down, and will turn off when you release it
(Unlatched). Immediately after you press the key, a
MIDI message with 7F(H) as the SW value will be
transmitted; immediately after you release the key, a
MIDI message with a SW value of 00(H) will be
transmitted.
If a specific byte is set to "ENC" (or "FAD") in a mes-
sage assigned to an ENCODER [ON] key or a CH
[ON] key, use the LATCH button to select one of the
following behaviors.
• If the LATCH button is on
If you press the key from the Off state, a MIDI message
with the current setting of the encoder (or fader) as the
ENC (or FAD) value will be transmitted, and when you
press the same key once again a MIDI message with a
value of 00(H) as the ENC (or FAD) value will be
transmitted.
• If the LATCH button is off
The moment you press the key, a MIDI message with
the current setting of the encoder (or fader) as the ENC
(or FAD) value will be transmitted; the moment you
release the key, a MIDI message with 00(H) as the ENC
(or FAD) value will be transmitted.
Note
If SW/ENC/FAD is not specified as the last byte of the MIDI
message, turning the key on or off will transmit the same MIDI
message; i.e., the same message is transmitted when the key
goes off.