Yamaha PM5D Owner's Manual page 124

16
Remote control
When controlling a continuously-variable parameter,
that parameter will be at its minimum value when the
voltage is at low level, and at its maximum value when
the voltage is at high level.
GPI IN FUNCTION column
status
POLARITY column
While the GPI screen is displayed, the GPI IN status
column of the GPI IN area will show a yellow bar
graph to indicate the approximate value of the voltage
being input to each port. (If the bar is not shown, the
voltage is grounded; if the bar is displayed all the way
to the right edge, the voltage is at high level.)
Hint
The voltage value at which the PM5D detects High or Low
level can be adjusted to suit the external controller (except for
external switches) you are using ( ➥ p.125).
4 At the left edge of the FUNCTION column,
click the button to open the GPI IN PORT
ASSIGN window.
In the GPI IN PORT ASSIGN window you can select
the PM5D function that will be controlled by each GPI
IN port.
Use the FUNCTION column to select the type of func-
tion, and use the PARAMETER column to select the
optional parameters. You can select the following func-
tions and parameters.
FUNCTION PARAMETER
NO
—
ASSIGN
DIMMER ON
SOURCE =
MONITOR [monitor
source name]
MONO ON
124
PM5D/PM5D-RH Owner's Manual
PARAMETER
column
PM5D operation
No assignment
Switches the Dimmer func-
tion on/off
Switches the monitor source
Switches the Monitor section
[MONO] key on
Operating section
FUNCTION PARAMETER
Switches the Talkback func-
LATCH
tion on/off (latched operation)
TALK-
Switches the Talkback func-
BACK ON
UNLATCH tion on/off (unlatched opera-
tion)
CH ON- [channel Switches the channel on/off
LATCH name] (latched operation)
CH ON- [channel Switches the channel on/off
UNLATCH name] (unlatched operation)
Modifies the fader value
FADER [channel
(LEVEL parameter) accord-
LEVEL name]
ing to the voltage
Modifies the surround pan-
FRONT-REAR ning (front/rear) of the
PAN [SEL] selected channel according
to the voltage
Modifies the surround pan-
LEFT-RIGHT ning (left/right) of the selected
PAN [SEL] channel according to the volt-
age
Modifies the surround pan-
ning (front/rear) of the
FRONT-REAR
selected odd-numbered
PAN [ODD]
channel according to the volt-
SUR-
age
ROUND
Modifies the surround pan-
PAN
LEFT-RIGHT ning (left/right) of the selected
PAN [ODD] odd-numbered channel
according to the voltage
Modifies the surround pan-
ning (front/rear) of the
FRONT-REAR
selected even-numbered
PAN [EVEN]
channel according to the volt-
age
Modifies the surround pan-
LEFT-RIGHT ning (left/right) of the selected
PAN [EVEN] even-numbered channel
according to the voltage
While the external input is
USER
[User Defined active, executes the same
DEFINED
key bank / key operation as when the
KEY
number] selected User Defined key is
FUNCTION
pressed
USER [User Defined While the external input is
DEFINED key bank / key active, lights the LED of the
KEY LED number] selected User Defined key
PEAK Switches the Peak Hold func-
HOLD ON tion on/off
OSCILLA-
— Switches the Oscillator on/off
TOR ON
Switches the Solo function
SOLO ON
on/off
After you have specified the function and parameter,
click the OK button.
Note
• If latched operation is selected, the port will change between
active/inactive each time a trigger is input from an external
switch. In this case, we recommend that you use a non-lock-
ing type of external switch.
• If unlatched operation is selected, the port will be active only
while the signal from the external switch stays at high level
or low level. In this case, we recommend that you use either
a non-locking or a locking type of external switch as appro-
priate for your situation.
PM5D operation