Yamaha PM5D Owner's Manual page 304

Effects Parameters
❏ REV→PAN
One input, two output reverb and autopan effects in
parallel.
Parameter Range
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
HI. RATIO 0.1–1.0
DIFF. 0–10
DENSITY 0–100%
THRU, 21.2 Hz–
HPF
8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
REV.BAL 0–100%
FREQ. 0.05–40.00 Hz
DEPTH 0–100%
*1
DIR.
WAVE Sine, Tri, Square
SYNC OFF/ON
*2
NOTE
*1. L↔R, L→R, L←R, Turn L, Turn R
*2.
❏ DELAY+ER.
One input, two output delay and early reflections effects in
parallel.
Parameter Range
DELAY L 0.0–1000.0 ms
DELAY R 0.0–1000.0 ms
FB. DLY 0.0–1000.0 ms
FB. GAIN –99 to +99%
HI. RATIO 0.1–1.0
THRU, 21.2 Hz–
HPF
8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
DLY/ER 0–100%
S-Hall, L-Hall, Ran-
TYPE dom, Revers, Plate,
Spring
ROOMSIZE 0.1–20.0
LIVENESS 0–10
INI. DLY 0.0–500.0 ms
DIFF. 0–10
DENSITY 0–100%
ER NUM. 1–19
SYNC OFF/ON
*1
NOTE L
NOTE R 1
NOTE FB 1
*1.
(Maximum value depends on the tempo setting)
304
PM5D/PM5D-RH Owner's Manual
Description
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Spread
Reverb density
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Reverb and panned reverb bal-
ance (0% = all panned reverb,
100% = all reverb)
Modulation speed
Modulation depth
Panning direction
Modulation waveform
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine FREQ.
Description
Left channel delay time
Right channel delay time
Feedback delay time
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
High-frequency feedback ratio
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Delay and early reflections bal-
ance (0% = all delay, 100% = all
early reflections)
Type of early reflection simulation
Reflection spacing
Early reflections decay characteris-
tics (0 = dead, 10 = live)
Initial delay before reverb begins
Spread
Reverb density
Number of early reflections
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine left channel DELAY L
Used in conjunction with TEMPO
to determine right channel DELAY
R
Used in conjunction with TEMPO
to determine FB. DLY
Reference section
❏ DELAY→ER.
One input, two output delay and early reflections effects in
series.
Parameter Range
DELAY L 0.0–1000.0 ms Left channel delay time
DELAY R 0.0–1000.0 ms Right channel delay time
FB. DLY 0.0–1000.0 ms Feedback delay time
Feedback gain (plus values for
FB. GAIN –99 to +99% normal-phase feedback, minus
values for reverse-phase feedback)
HI. RATIO 0.1–1.0 High-frequency feedback ratio
THRU, 21.2 Hz–
HPF High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
Delay and early reflected delay
DLY.BAL 0–100% balance (0% = all early reflected
delay, 100% = all delay)
S-Hall, L-Hall, Ran-
TYPE dom, Revers, Plate, Type of early reflection simulation
Spring
ROOMSIZE 0.1–20.0 Reflection spacing
Early reflections decay characteris-
LIVENESS 0–10
tics (0 = dead, 10 = live)
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
ER NUM. 1–19 Number of early reflections
SYNC OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*1
NOTE L
to determine left channel DELAY L
Used in conjunction with TEMPO
NOTE R 1 to determine right channel DELAY
R
Used in conjunction with TEMPO
NOTE FB 1
to determine FB. DLY
*1.
(Maximum value depends on the tempo setting)
❏ DELAY+REV
One input, two output delay and reverb effects in parallel.
Parameter Range
DELAY L 0.0–1000.0 ms Left channel delay time
DELAY R 0.0–1000.0 ms Right channel delay time
FB. DLY 0.0–1000.0 ms Feedback delay time
Feedback gain (plus values for
FB. GAIN –99 to +99% normal-phase feedback, minus
values for reverse-phase feedback)
Delay high-frequency feedback
DELAY HI 0.1–1.0
ratio
THRU, 21.2 Hz–
HPF High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
Delay and reverb balance (0% =
DLY/REV 0–100%
all delay, 100% = all reverb)
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
REV HI 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
SYNC OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*1
NOTE L
to determine left channel DELAY L
Used in conjunction with TEMPO
NOTE R 1 to determine right channel DELAY
R
Used in conjunction with TEMPO
NOTE FB 1
to determine FB. DLY
*1.
(Maximum value depends on the tempo setting)
Description
Description