Cessna TURBO CENTURION T210M 1978 Pilot Operating Handbook page 258

CESSNA 400 NAV/COM
(TYPE RT-485A)
PILOT'S OPERATING HANDBOOK
' SUPPLEMENT
1. COM MEMORY 1, 2
&
3 PUSHBUTTONS - When a COM MEMORY pushbutton is
pressed, the preset selected frequency will appear in the COM frequency window
for use as the selected operating frequency. Each pushbutton will illuminate
white when pressed and the light will go out on the previously selected pushbut-
ton. Three preset frequencies may be stored in MEMORY and selected as desired,
by merely pressing the appropriate COM MEMORY pushbutton to recall the
desired operating frequency. If electrical power to the set's "keep-alive"circuit
has not been interrupted, upon turn-on, the set will automaticaly recall the last
COM MEMORY frequency selected by the MEMORY pushbutton.
If
electrical
power is removed from the set's "keep-alive" circuit (such as radio removal or
battery replacement) for more than 15 seconds, upon turn-on, the COM MEMORY
circuits will have to be reset and COM 1 MEMORY will automatically be selected
with the lowest operating frequency (118.000 MHz) selected.
2. COMMUNICATION OPERATING FREQUENCY READOUT - Indicates COM
frequency in use. Third decimal place not shown.
3. CYCLE BUTTON (C) - Selects last illuminated decimal place on COM frequency
in use. If last decimal place is 2 or 7, pressing Cpushbutton changes number to
5
or
0, respectively.
If
last decimal place is 5 or 0, pressing C pushbutton changes
number to 7 or 2, respectively. When the last illuminated digit on the set is 2 or 7,
the third digit on the set (not shown) will always be 5. When the last illumi:nated
digit on the set is
O
or 5, the third digit on the set (not shown) will always be 0. Also
provides test function by holding C pushbutton pressed for more than 1.7 seconds.
This lights each COM and NA V MEMORY pushbutton in turn, and displays the
corresponding preset frequency in MEMORY.
4. NAVIGATION OPERATING FREQUENCY READOUT - Indicates NAV fre-
quency in use.
5. NAV MEMORY 1, 2
&
3 PUSHBUTTONS - When a NAV MEMORY pushbutton is
pressed, the preset selected frequency will appear in the NA V frequency window
for use as the selected operating frequency. Each pushbutton will illuminate
white when pressed and the light will go out on the previously selected pushl>µt- .
ton. Three preset frequencies may be stored in MEMORY and selected as desi:r.ect, •.,
by merely pressing the appropriate NAV MEMORY pushbutton to recall the
desired operating frequency. If electrical power to the set's "keep-alive" circuit
has not been interrupted, upon turn-on, the set will automatically recall the last
NA V MEMORY frequency selected by the MEMORY pushbutton.
If
electrical
power is removed from the set's "keep-alive" circuit (such as radio removal or
battery replacement) for more than 15 seconds, upon turn-on, the NAV MEMORY
circuits will have to be reset and NAV 1 MEMORY will automatically be selected
with the lowest operating frequency (108.000 MHz) selected.
6. ID-VOX-T SWITCH - In ID position, station identifier signal is audible; in VOX
(Voice) position, identifier signal is suppressed; in T (Momentary On) position,
the self-test function is selected, and the AP/CPLD annunciator illuminates
amber and the XMIT annunciator illuminates green.
7. NAVIGATION RECEIVER FREQUENCY SELECTORS - Outer knob changes
NAV frequency in 1-MHz steps between 108 and 117 MHz; inner knob changes
NAV frequency in .05-MHz steps between .00 and .95 MHz; simultaneously selects
paired glide slope frequency and DME channel.
Figure
1,
Cessna 400 Nav/Com (Type RT-485A), Operating Controls and
Indicators (Sheet 2 of 4)
4
~