Setting 5: Air Compressor Application - YASKAWA U1000 Series Technical Manual

4.6 Application Selection
No.
b1-01 Frequency Reference Selection 1
b1-02 Run Command Selection 1
b1-03 Stopping Method Selection
b1-04 Reverse Operation Selection
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
C6-02 Carrier Frequency Selection
d2-01 Frequency Reference Upper Limit
 Setting 5: Air Compressor Application
No.
A1-02 Control Method Selection
b1-04 Reverse Operation Selection
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
C6-01 Drive Duty Model Selection
E1-03 V/f Pattern Selection
L2-01 Momentary Power Loss Operation Selection
No.
b1-01 Frequency Reference Selection 1
b1-02 Run Command Selection 1
b1-04 Reverse Operation Selection
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
 Setting 6: Hoist Application
Note: 1. Read the instructions listed on page
2. Perform Auto-Tuning after selecting the Hoist Application Preset.
No.
A1-02 Control Method Selection
b1-01 Frequency Reference Selection 1
b6-01 Dwell Reference at Start
b6-02 Dwell Time at Start
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
C6-01 Drive Duty Mode Selection
C6-02 Carrier Frequency Selection
d1-01 Frequency Reference 1
d1-02 Frequency Reference 2
d1-03 Frequency Reference 3
E1-03 V/f Pattern Selection
H2-01 Terminals M1-M2 Function Selection
H2-02 Terminals M3-M4 Function Selection
H3-06 Terminal A3 Function Selection
L2-03 Momentary Power Loss Minimum Baseblock Time
L3-04 Momentary Power Loss Voltage Recovery Ramp Time
L4-01 Speed Agreement Detection Level
L4-02 Speed Agreement Detection Width
L6-01 Torque Detection Selection 1
L6-02 Torque Detection Level 1
L6-03 Torque Detection Time 1
L8-07 Output Phase Loss Protection Selection
L8-38 Carrier Frequency Reduction Selection
L8-41 High Current Alarm Selection
<1> Max. setting value varies by the drive model selection (o2-04).
112
Table 4.13 HVAC Fan: User Parameters (A2-01 to A2-16)
Parameter Name
Table 4.14 Compressor: Parameter Settings
Parameter Name
Table 4.15 Compressor: User Parameters (A2-01 to A2-16):
Parameter Name
113 when using Hoist Application Preset
Table 4.16 Hoist: Parameters and Settings
Parameter Name
No.
d2-02 Frequency Reference Lower Limit
E1-03 V/f Pattern Selection
E1-04 Maximum Output Frequency
E2-01 Motor Rated Current
H3-11 Terminal A2 Gain Setting
H3-12 Terminal A2 Bias Setting
L2-01 Momentary Power Loss Operation Selection
o4-12 kWh Monitor Initialization
0: V/f Control
1: Reverse Prohibited
5.0 s
5.0 s
0: Heavy Duty (HD)
F: Custom V/f pattern
1: Enabled
No.
E1-03 V/f Pattern Selection
E1-07 Middle Output Frequency
E1-08 Middle Output Frequency Voltage
E2-01 Motor Rated Current

2: Open Loop Vector Control
0: Operator
3.0 Hz
0.3 s
3.0 s
3.0 s
0: Heavy Duty (HD)
2: 6.0 kHz
<1>
6.0 Hz
30.0 Hz
50. 0 Hz
F: Custom V/f pattern
5: Frequency Detection 2
37: During Frequency Output
1F: Through mode
0.3 s
0: Disabled
2.0 Hz
0.0 Hz
8: UL3, UL4 at speed agree (fault)
2%
0.5 s
1: Enabled
1: Enabled below 6 Hz
1: Enabled (alarm is output)
YASKAWA ELECTRIC SIEP C710636 03A YASKAWA U1000 Technical Manual
Parameter Name
Default Setting
Parameter Name

Default Setting