Front Panel Lcd Menu Operations; System Settings Menu - Lightware MX2-8x8-HDMI20-L User Manual


  
4. Operation
4.3. Front Panel LCD Menu Operations
The company logo is displayed on the screen
during the boot-up. The main menu is displayed
after about 30 seconds later and the device is
ready to use.
Menu Structure
The front panel has a color LCD that shows the most important
settings and parameters structured in a menu. The jog dial control
knob can be used to navigate between the menu items or change the
value of a parameter. The knob can be pressed to enter a menu or
edit/set a parameter.
System Settings
Network
RS-232
Time and Date
Display Brightness
Buzzer
Power redundancy
Device Info
Enter Standby Mode
Restore Factory Defaults
Input Ports
Port
Video Status
Video Settings
Analog audio
Output Ports
Port
Video Status
Video Settings
Analog audio
EDID
View
Switch
Save
Health
Uptime
Control Panel
Motherboard
IO ports
Presets
Load Preset
Save Preset
Parameter Selection
The blue
selected
green
setting.
TIPS AND TRICKS: The faster
you rotate the jog dial, the faster
the parameter list is scrolled.
Enter the menu/ submenu
Icon before the line indicates the additional submenus. Click with

the rotary to enter.
·
MAIN MENU Icon shows, that there is no submenu or setting possibility.
System Settings
Input Ports
DEVICE INFO
Output Ports
Frame serial number
•
EDID
Hardware versions
Health
Firmware versions
Presets
Menu navigation
«
Back
& change parameter
4.3.1. System Settings Menu
Up Down
Network Submenu
The parameters of the network
connection can be set in this
Menu selection
submenu. The first three lines (IP,
& set parameter
Subnet, and Gateway parameters)
Press
show the current settings. If the
DHCP option is disabled, three
more parameters are listed which
can be set for a static IP address:
▪
▪
▪
ATTENTION! If you change the network settings, always press the
Save option under Network menu (not only in the submenu of the
parameter) to apply the new settings.
MX2-HDMI20 series – User's Manual
OUTPUT MODE
colored line means the
Auto
menu/parameter, the
HDMI
one means the current
DVI
« Back
DEVICE INFO
Frame serial number
95144905
Hardware versions
Firmware versions
« Back
NETWORK
IP 192.168.0.97

Subnet 255.255.255.0
Gateway 192.168.0.1
DHCP Enabled
Link Status 100 Mbps full-duplex
MAC 00:14:2d:2b:43:89
« Back
Static IP,
Static Subnet,
Static Gateway.
RS-232 Submenu
Adjustable parameters of the port:
▪ Control (enable/disable the
device control),
▪ Baud Rate (9600, 19200,
38400, 57600, 115200),
Protocol (LW2, LW3 or P#2
▪
protocol).
Time and Date
The internal clock and date can
be set in this submenu which is
used for logging events.
95144905
Display Brightness
The brightness of the LCD can be
set from 1 to 10 on a scale.
ATTENTION! The lowest value
of the brightness parameter
is 1 when setting via the front
panel. The setting is available
in Lightware Device Controller
software as well, but in that
case, the lowest value is 0,
which means the display is
switched off; see Front Panel
Tab section.
Save
INFO: When the matrix is in Standby mode, the display is switched off.
Buzzer
There is a buzzer (beeper) in the matrix which sounds in certain cases
(during booting, network or parameter change, etc.). It can be enabled/
disabled in this submenu.
21
RS-232
Control Enabled
Baud Rate 57600
Protocol LW3
«
Back
DATE
2019 - 06 - 18
« Back
Save
DISPLAY BRIGHTNESS
9 ☼
☼
0 1 2 3 4 5 6 7 8 9 10
«
Back Save