Drive Specifications - YASKAWA FSDrive-MV1000 Series Instructions For Use Manual

A.2 Drive Specifications
A.2 Drive Specifications
Item
Efficiency
Power Factor
Cooling Method
Control Method
Main Circuit
Frequency Control
Range
Frequency Control
Accuracy
Analog Input
Resolution
Accel/Decel Time
Torque Accuracy
Overload Tolerance
Momentary Power
Loss Compensation
Time
<2>
Main Control
Functions
Protective Functions
PLC Functions (Optional)
Maintenance Tools
Communications
(Optional)
<3>
Input Transformer
Temperature Protection
Control Panel
Main Circuit
Protection Design
Ambient
Temperature,
Relative Humidity
Storage Temperature -20°C to +60°C (for very short term when handling)
Atmosphere
Painting
Form
Applicable Standards
<1> Adjustments (e.g., to parameters) are required after auto-tuning.
<2> When using the momentary power loss compensation function, an uninterruptible power supply unit option is required for the control power
supply.
<3> An option card and additional wiring are required to use the communications function. For CP-215 communication, an optional expansion PLC
board is required.
<4> Refer to Long Term Storage of Drives on page 71
<5> Refer to European Standards on page 220
218
Table A.6 Drive Specifications
Approx. 97% (At rated motor speed, 100% load)
Min. 0.95 (At motor rated speed, 100% load)
Forced air-cooling by fan (with failure detection)
Open Loop Vector Control (OLV), Closed Loop Vector Control (CLV), V/f control (for multiple motor
operation), Closed Loop Control for SM (optional)
Voltage-type PWM control with multiple outputs connected in series
(Power Cell: 3-level output)
0.01 to 120 Hz
±0.5%
0.03 Hz
0.1 to 6000 s
±5% (OLV), ±3% (CLV)
<1>
Continuous rated current 100%, overload tolerance 110% for 1 minute and 120% for 15 seconds
Max. 2 seconds
Torque control, Droop control, Speed/torque control switch, Momentary power loss compensation, Speed
search, Overtorque detection, Torque limit, 17-step speed (max.), Accel/decel time switch, S-curve accel/decel,
Auto-tuning (rotational, stationary), Dwell, Cooling fan on/ off, Slip compensation, Torque compensation,
Frequency jump, Upper/lower limits for frequency reference, DC injection braking at start and stop, PID
control (with sleep function), MEMOBUS communication (RS-485, max. 115.2 kbps), Fault retry
Overcurrent, Overvoltage, Undervoltage, Output ground fault, Output open-phase, Overload, Cooling-fan
error, Transformer overheat, Motor overheat, etc.
Expansion PLC board
USB: DriveWizard Plus MV
• RS-485: MEMOBUS (Modbus)
• One of the following hardware; PROFIBUS-DP, DeviceNet, Ethernet, or CP-215 can be installed.
Class H dry type, -5%/N/+5% tap, secondary multi-phase winding
Power Cells: protected by thermistor for temperature
Transformer: protected by temperature monitor (PT100 Ω) and thermo switches
Status display, Fault display, Parameter setting, Parameter reference
Power Cell construction
IP40 (simplified dustproof type)
-5°C to +40°C with derating, 85% RH maximum (no condensation)
General environmental conditions, free from dust and corrosive gases
Altitude: 0 to 2000 m
Munsel 5Y7/1 semi gloss for inner and outer faces
Made of enclosing steel sheets, vertical standalone type, front maintenance type
JIS, JEM, JEC
<5>
for details on the long term storage of the drives.
for details on compliance with CE standards.
Specifications
<4>
YASKAWA ELECTRIC TOEP C710687 02B FSDrive-MV1000 Instructions