1. Manuals
  2. Brands
  3. NBase-Xyplex Manuals
  4. Server
  5. MAXserver 1608A
  6. Getting started

NBase-Xyplex MAXserver 1608A Getting Started

Access servers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Getting Started
With
MAXserver™ Access Servers
Models 1604, 1608A/B, 1620 and 1640
NBase-Xyplex
295 Foster St.
Littleton, MA 01460
1-800-435-7997 (U.S.)
+978-952-4888 (International)
Email: support@Nbase-Xyplex.com
451-0038D

Advertisement

Table of Contents
loading

Summary of Contents for NBase-Xyplex MAXserver 1608A

  • Page 1 Getting Started With MAXserver™ Access Servers Models 1604, 1608A/B, 1620 and 1640 NBase-Xyplex 295 Foster St. Littleton, MA 01460 1-800-435-7997 (U.S.) +978-952-4888 (International) Email: support@Nbase-Xyplex.com 451-0038D...
  • Page 2 All rights reserved. No part of this publication may be reproduced without the prior written consent of NBase-Xyplex. The information in this document is subject to change without notice and should not be construed as a commitment by NBase-Xyplex. NBase-Xyplex reserves the right to revise this publication, and to make changes in content from time to time, without obligation to provide notification of such revision or changes.
  • Page 3 0038...
  • Page 4 Connect the power cord of the equipment into an outlet on a circuit that is different from that to which the receiver is connected. · Consult the dealer or experienced radio/TV technician for help. Changes or modifications not expressly approved by NBase-Xyplex could void the user's authority to operate the equipment. 0038...
  • Page 5 VCCI Translation: This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

  • Page 7: Table Of Contents

    Table of Contents About the MAXserver ..................13 Supported Communication Speeds ................15 Software Requirements....................15 Downloading Software ....................16 Configuration Options....................17 Related Publications....................19 Installation ...................... 20 Unpack and Inspect the Unit ..................21 Place the Unit on a Flat Surface or Mount on Rack ..........21 Rack Mount Installation (optional) ................
  • Page 8 Flash Cards.....................51 Loading the Image File ....................51 Changing the Software Image Filename..............52 Copying Flash Cards ....................53 Deleting Flash Cards....................53 Displaying the Flash Card Settings ................53 Updating Images ......................55 Rebooting......................57 INITIALIZE DELAY Command ................57 Cabling Considerations .................60 Ordering Cables ......................
  • Page 9 Defining Dumping Methods..................96 Defining IP Addresses....................99 Miscellaneous Unit Configuration ................100 Resetting the Unit’s Load and Dump Protocols to Factory Defaults ....102 Initializing Server and Port Parameters ..............104 Revert to Stored Configuration ................104 Exit Saving Configuration Changes................ 105 Exit Without Saving Configuration Changes ............
  • Page 10 Verifying Memory Installation Using the Configuration Menu ......149 Removing SIMMs...................... 152 Removing SIMMs from the MAXserver ..............153 Technical Specifications................155 Index Figures Figure 1 - Sample SHOW UNIT Display ..............16 Figure 2 - Sample FocalPoint Configuration ............18 Figure 3 - Mounting a MAXserver in Rack ...............
  • Page 11 Figure 33 - Sample Primary Initialization Record Display ........108 Figure 34 - Primary Initialization Record Display..........118 Figure 35 - Sample Error Code Display ..............130 Figure 36 - Typical SIMM ..................144 Figure 37 - Removing the Screws Securing the Cover.......... 145 Figure 38 - Location of SIMM Sockets ..............

  • Page 13: About The Maxserver

    MAXserver 1640. Figure 6 and Figure 8 show rear and front views of the MAXserver 1608A and MAXserver 1604. NOTE: The front and rear panels of the MAXserver 1608A are identical to the MAXserver 1620 and 1640 except for the number of ports available.
  • Page 14 8 MB, using SIMM memory modules. SIMMs should be installed by qualified personnel only. To upgrade your MAXserver, contact your NBase-Xyplex sales representative or distributor. Installation instructions are provided later in this Guide. Concurrent Flow Control and Modem Control Support -- The MAXserver provides concurrent support for RTS/CTS flow control signals and modem control;...

  • Page 15: Supported Communication Speeds

    Getting Started with MAXserver Access Servers Supported Communication Speeds MAXserver Communication Speed MAXserver 1604 50 - 115.2 Kbps MAXserver 1608A/B 50 - 115.2 Kbps MAXserver 1620 50 - 115.2 Kbps MAXserver 1640 50 bps to 57.6 Kbps Software Requirements MAXserver...

  • Page 16: Downloading Software

    Getting Started with MAXserver Access Servers Hardware Type: Hardware Revision: 00.00.00 Rom Revision: 470000 Software Type: Access Server Level 4 Software Revision: V6.1 Protocol Type: LAT, TELNET, RLOGIN, TN3270, ARAP, SNMP, PPP, IPX, XPRINTER Daemon(s): Enabled Feature(s): APD, HELP, INTERNET SECURITY, IP FILTERING, IPX FILTERING, ULI, SECURID, MENU, NESTED MENUS, KERBEROS, RADIUS APD Message:...

  • Page 17: Configuration Options

    FocalPoint automatically ships free of charge on the software and documentation CD with all Network 3000, Route Runners, MAXserver, and 720 Series Access Server modules for the Network 9000. The latest versions of FocalPoint software are also available from the NBase-Xyplex Web Site. 0038...

  • Page 18: Figure 2 - Sample Focalpoint Configuration

    Getting Started with MAXserver Access Servers To use FocalPoint, simply load the software from the CD that was shipped with the MAXserver. From FocalPoint, you can select your MAXserver model and also provide all pertinent information before you can advance to the next step.

  • Page 19: Related Publications

    Related Publications The following publications are useful to persons who install and manage NBase-Xyplex access servers. The following publications were included on the CD with your access server software. To obtain hard copies, contact your NBase-Xyplex sales representative or distributor.

  • Page 20: Installation

    3. If the unit is equipped with a flash card, insert the into the card slot on the front of the unit. NOTE: NBase-Xyplex recommends that you wear a grounded wrist strap when you insert the card. If none is available, ground yourself by placing...

  • Page 21: Unpack And Inspect The Unit

    3. Place all packing materials back into the shipping carton and save the carton. (If you need to return the unit to NBase-Xyplex or your distributor, you should return it in the original carton.) 4. If the unit has been damaged in shipping or any parts are missing, notify your NBase-Xyplex representative or distributor immediately.

  • Page 22: Rack Mount Installation (Optional)

    Getting Started with MAXserver Access Servers To reduce the possibility of dust entering the unit and to allow easy inspection of the unit's front panel lights, make sure that the MAXserver is located at an optimum distance (preferably not less than 18 inches/45 centimeters) from the floor.

  • Page 23: Insert The Flash Card (If Supplied)

    If the unit is supplied with a Flash Card, insert the card into the card slot on the front panel. NBase-Xyplex recommends that you wear a grounded wrist strap when you insert the flash card. If none is available, ground yourself by placing one hand on the...

  • Page 24: Connecting The Ethernet Interface

    Getting Started with MAXserver Access Servers Connecting the Ethernet Interface Connect either a 10Base-T or AUI Ethernet network cable to the appropriate connector on the rear of the MAXserver (See Figure 4 for 20-port and 40-port models; Figure 5 for 8-port and 4-port models.) Connect only one Ethernet cable to the unit.

  • Page 25: Figure 5 - Maxserver 1604/1608B, Rear View

    Getting Started with MAXserver Access Servers Figure 5 - MAXserver 1604/1608B, Rear View Standard (AUI) Connection -- Plug the male cable connector into the 15- pin female AUI socket on the rear of the unit and fasten the slide latch. (The AUI connector signal assignments are shown in Figure 25.) 10Base-T Connection -- Install the Ethernet cable by plugging it into the 10Base-T connector on the rear of the unit.

  • Page 26: Connect The Power Cable

    Getting Started with MAXserver Access Servers Connect the Power Cable You do not need to set the unit for 115V or 230V operation. The power supply automatically adapts to the input voltage. A grounded AC power outlet should be located within six feet of the back of the unit.

  • Page 27: Front Panel Leds - Maxserver 1620/1640

    Getting Started with MAXserver Access Servers Front Panel LEDs - MAXserver 1620/1640 The front panels of the MAXserver 1640 and 1620 access servers are identical, except for the model designation. If, after several minutes, the front panel lights do not behave as indicated, refer to the Troubleshooting section of this guide for instructions.

  • Page 28: Figure 7 - Maxserver 1604 Front Panel

    Getting Started with MAXserver Access Servers Ports 1- 4 These lights indicate port activity. Memory Card Slot Flashing = Activity associated with port. ON = Port connection established. OFF = No port connection established. CONSOLE light - ON when someone is logged on to the unit’s console port via the network.

  • Page 29: Port Status Leds

    Getting Started with MAXserver Access Servers Port Status LEDs The port status LEDs are used in several ways. During the initialization process, the LEDs indicate that self-tests are being performed, and if any self-test fails, they indicate an error code. After the unit has received a load image and parameters, the lights indicate when a port is actively being used.

  • Page 30: Additional Considerations For An Internet Environment

    Getting Started with MAXserver Access Servers NBase-Xyplex recommends that you label all cables with the name of the device to which it connects and the number of the port you have assigned to it. This way, if the cable is removed for any reason, you can reconnect it easily.

  • Page 31: Autobauding Feature

    Getting Started with MAXserver Access Servers Table 1 - Factory Default Settings Configuration Factory Default Setting Initialization Record 1 Enabled Initialization Record 2 Disabled Initialization Record 3 Disabled Parameter file load method NVS, XMOP, MOP, BOOTP, RARP Software Image load method* CARD, XMOP, MOP, BOOTP, RARP, DTFTP* Dump File Method...
  • Page 32 Getting Started with MAXserver Access Servers NOTE: Access servers do not autobaud when the port receives 7-bit characters with EVEN parity from the device until software loading has completed. You must use 8-bit characters with parity set to NONE in order to receive load messages and to enter into the ROM Configuration Menu.

  • Page 33: Reinitializing/Powering Off The Unit

    Getting Started with MAXserver Access Servers Reinitializing/Powering Off the Unit The MAXserver always stores permanent parameters (i.e., those parameters that you change using the DEFINE or PURGE command) in local storage. Some of the DEFINE SERVER Commands require that you reboot the server for the changes to take effect.

  • Page 34: Figure 9 - Monitor Parameter Server Display

    Getting Started with MAXserver Access Servers The following screen displays: Xyplex>> MONITOR PARAMETER SERVER MX1620 V6.0.4S18 Rom 470000 HW 00.00.00 Lat Protocol V5.2 Uptime: 13 18:11:56 Address: 88-00-87-23-33-6B Name: X03346B Number: 21 Dec 1998 10:24:45 Check Timer: Parameter Server Limit: Retransmit Timer: Parameter Servers: Retransmit Limit:...

  • Page 35: Figure 10 - Reset Switch Location

    Getting Started with MAXserver Access Servers XYPLEX MAXSERVER 1600 CARD RUN LAN CONSOLE TERMINAL SERVER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Reset switch -- Press once to put the unit in reset state. Press again to re-initialize the unit.

  • Page 36: Connecting Other Devices

    Getting Started with MAXserver Access Servers Connecting Other Devices If you are connecting a modem, printer, plotter, host computer, or data switch, refer to the following documentation for instructions, as follows: Serial Printers, Plotters -- See the Printer Configuration Guide. Modems, Data Switches –...

  • Page 37: Logging In To The Access Server

    Getting Started with MAXserver Access Servers Logging in to the Access Server When your terminal is properly connected to the unit, turn its power ON, then press <RETURN> (or ENTER) a few times -- until the unit recognizes the terminal. When the unit responds, you see the following message on your screen: WELCOME TO THE XYPLEX ACCESS SERVER.
  • Page 38 Getting Started with MAXserver Access Servers privileged mode. XYPLEX>> See the Commands Reference Guide for the commands that require the user to be in Privileged mode. The unit is now ready to accept any of the commands described in the Commands Reference Guide. You can obtain on- screen information about the access server commands by typing HELP and pressing <RETURN>: XYPLEX>HELP...

  • Page 39: Telneting Into The Access Server Console Port

    Getting Started with MAXserver Access Servers Telneting into the Access Server Console Port Do the following to telnet into the console port on an access server: NOTE: You should issue both the DEFINE and SET commands where they are indicated in the following procedure. Issuing both the DEFINE and SET commands ensures that the parameter change will take effect without rebooting the unit.

  • Page 40: Figure 11 - Sample Show Port 0 Telnet Characteristics Display

    Getting Started with MAXserver Access Servers Configure the Subnet Mask for the access server. The subnet mask must be consistent with the network on which the access server will reside. Use the following commands: define server ip subnet mask [ ip-address ] set server ip subnet mask [ ip-address ] Configure the default first-hop Router/Gateway: define server ip primary gateway address [ ip-address ]...
  • Page 41 Getting Started with MAXserver Access Servers If you are trying to telnet from one NBase-Xyplex device into another NBase-Xyplex access server’s console port, the command you will use is: telnet x.x.x.x:2000 where “x.x.x.x” represents the IP address of the destination access server.

  • Page 42: Changing The Telnet Remote Port

    Getting Started with MAXserver Access Servers Changing the Telnet Remote Port While you are logged into a port in privileged mode, you can change the telnet remote port on port 0 from 2000 to 23. Use the following commands: define port 0 telnet remote 23 logout port 0 Now you can telnet to the IP without a socket number.

  • Page 43: Login Password

    Getting Started with MAXserver Access Servers Login Password When you enable the Login Password feature on a server port, a person attempting to log on to that port must enter a password in order to gain access. A single password is used at all ports where the feature is enabled. The login password feature is optional.
  • Page 44 Getting Started with MAXserver Access Servers NBase-Xyplex recommends that you change the default password to restrict access to the commands that: · Change the server’s settings · Affect other users’ ports · Affect access to destinations on the network You might want to change the privilege password periodically, to limit the number of users who can set privileged mode.

  • Page 45: Lost Passwords

    Getting Started with MAXserver Access Servers Lost Passwords NBase-Xyplex access servers are extremely secure. If you should lose your password, reset the unit back to factory defaults and reconfigure as new. New passwords should be properly maintained by the system administrator.

  • Page 46: Prompts

    Getting Started with MAXserver Access Servers Prompts The local command mode prompt changes to indicate that the port is a privileged port (unless the command is issued from a console port). For example, the default local command mode prompt for a non-privileged port is Xyplex>.
  • Page 47 Getting Started with MAXserver Access Servers The default values are, "Enter username>" and "Enter user password>." If the server booted from an existing parameter file, the username prompt is, "Enter username>." For the password prompt, the default value is "Enter user password>." However, if SecurID is enabled on the port, the default password prompt is "Enter PASSCODE:."...

  • Page 48: Privileges

    Getting Started with MAXserver Access Servers Privileges Privilege levels determine which commands users can enter at server ports. The server supports three privilege levels, described in Table 2. The default privilege level for all ports is Nonprivileged. Table 2 - Privilege Levels Privilege Level Description Privilege...
  • Page 49 Getting Started with MAXserver Access Servers The port will have privileged status. This means that the user at the port can set or change operational and permanent parameters for the server, and any or all ports, sessions, or services. When the port is logged out, it will automatically return to a non-privileged status for the next user.
  • Page 50 Getting Started with MAXserver Access Servers Secure ports do not accept commands that affect: · Server settings · Other user's ports · The accessibility of network destinations Use the following command to change the privilege level to Secure. Unless you set the default privilege level of a port to Secure through the following command, a port has the Nonprivileged security level: DEFINE/SET PORT[ port-list ]SECURITY ENABLED 0038...

  • Page 51: Flash Cards

    Getting Started with MAXserver Access Servers Flash Cards This section describes how to use flash cards. Flash cards are readable/writeable and can be updated to a newer software version. See the Software Installation Guide for Xyplex Loaders for instructions. The commands used to update flash cards are located in the Commands Reference Guide.

  • Page 52: Changing The Software Image Filename

    Getting Started with MAXserver Access Servers Use the following command to load the image file: DEFINE SERVER LOAD [PRIMARY] SOFTWARE “FILENAME” [SECONDARY] [TERTIARY] Example This example specifies XPCSRV20 as the filename for the secondary initialization record. XYPLEX>> DEFINE SERVER LOAD SECONDARY SOFTWARE XPCSRV20 Changing the Software Image Filename The software load image filename appears in the Software field on the Loaddump characteristics display (see Figure 33).

  • Page 53: Copying Flash Cards

    Getting Started with MAXserver Access Servers Copying Flash Cards Use this command on units that have flash cards. You can copy the entire contents of one card to another with this command. XYPLES>> SET SERVER CARDCOPY Deleting Flash Cards Use this command on units that have flash cards. You can delete the entire contents of a flash card.
  • Page 54 Description Card Status: Formatted and write enabled. Card Type: Manufacturer - can be anyof the following: Fujitsu Micron Mitsubishi NEC NBase-Xyplex Samsung Toshiba Flash = SERIES 1, Flash2 = SERIES 2 Size of Flash card Card State: Idle Device Type: Manufacturing and size of ROM chips on the Flash card.

  • Page 55: Updating Images

    Getting Started with MAXserver Access Servers Get File Name: Name of file. Get File Area: Area of flash card to put file. Get File Current What the card is currently doing. State: Get File Previous Did previous GET FILE succeed. State: Parameter Area How many times the PARAM Area of the Flash card...
  • Page 56 Getting Started with MAXserver Access Servers AREA The area on the card where the image file is located. Depending on the file’s location, include either the IP address or Ethernet address where the file is located. NOTE: There is no Define command for this option. Examples SET SERVER GET CARD LOADFILE “xpcsrv20.sys”...

  • Page 57: Rebooting

    Getting Started with MAXserver Access Servers Rebooting Use the INITIALIZE SERVER command to reboot the access server, or to cancel a previous INITIALIZE SERVER command. Using the INITIALIZE command, the access server returns to a state which is exactly the same as if you powered up the server (i.e., all settings are restored to the values specified in the permanent database.
  • Page 58 Getting Started with MAXserver Access Servers If you specify INITIALIZE DELAY 0,the server will reboot immediately unless there are unsaved parameters, in which case you will receive the "Warning Configuration Not Saved" error message (message 198). If you specify INITIALIZE DELAY n with a delay value other than 0, and a user changes a permanent parameter (i.e., uses a Define command) before n minutes expire, the initialization is delayed until the parameters are saved.
  • Page 59 Getting Started with MAXserver Access Servers Examples INITIALIZE DELAY 1 NITIALIZE SERVER DELAY 5 INITIALIZE SERVER DELAY 5 OVERRIDE INITIALIZE CANCEL 0038...

  • Page 60: Cabling Considerations

    3 wires and is not suitable for modem-based applications. Standard cabling items available from NBase-Xyplex allow you to connect to any serial device that uses a male or female DB-25 connector. All you need...

  • Page 61: Modem Control/Hardware Flow Control

    Getting Started with MAXserver Access Servers 7-wire MAXserver 1100,1120,1500,1520, 1800, and 1820 Access Servers. 8-wire MAXserver 800, 1600,1604, 1608, 1620, 1640 Access Servers. Network 9000 Access Server 720 RJ-45 I/O Modules (Model 723). See the Modems section of the Basic Configuration Guide for information about modem control and setting up modems.

  • Page 62: Making Your Own Rj-45 Cables

    To use modem control or hardware flow control, you need an input control signal and an output control signal for each. This is important to consider when you decide which NBase-Xyplex unit to use for a particular application, since different NBase-Xyplex units support different wiring schemes, and some units might not have enough signals for the desired application.

  • Page 63: Rj-45 Wiring Considerations

    Getting Started with MAXserver Access Servers Also, NBase-Xyplex recommends that you use different colored wires for straight-through and crossover cables, in order to keep track of the cable type. For example, NBase-Xyplex recommends silver wire for making crossover cables and black wire for making straight-through cables.

  • Page 64: Modular Adapters (Rj-45 To Db-25)

    Modular Adapters (RJ-45 to DB-25) You can obtain adapters with male and female DB-25 connectors from NBase-Xyplex. These adapters direct signals from the RJ-45 connector on the cable to the correct pin on the DB-25 connector. Figure 13 and Figure 14 show how devices are cabled when you use these adapters.

  • Page 65: Figure 13 - Adapter Wiring, Maxserver To Dte

    Getting Started with MAXserver Access Servers MAXserver Modular Adaptor DTE Cable Connector Crossover Cable Female Male Male Female RJ-45 RJ-45 RJ-45 RJ-45 Female To DTE DB-25 Female RJ-45 Female DB-25 MAXserver DTE Device Male RJ-45 Male RJ-45 Connector Connector Connector Pin Signal Connector Connector...

  • Page 66: Figure 14 - Adapter Wiring, Maxserver To Dce

    Getting Started with MAXserver Access Servers MAXserver Modem Cable Modular Adaptor Connector Straight Through Cable Female Male Male Female RJ-45 RJ-45 RJ-45 RJ-45 Male To Modem DB-25 (a) Supports RING: MAXserver Male DB-25 Male RJ-45 DCE Device Male RJ-45 Female RJ-45 Connector Connector Connector...

  • Page 67: Deconnect Rj-45 Cables

    Getting Started with MAXserver Access Servers NOTES: In order to expand the functionality of the serial interface, the MAXserver modular cabling allows you to connect different signals to pin 7 of the MAXserver. (This pin is an input to the MAXserver.) When a DCE device is connected to a MAXserver serial port, the device's DCD output is connected to pin 7.

  • Page 68: Octopus Cables

    Getting Started with MAXserver Access Servers DEConnect Crossover Cable Male MMJ Male RJ-45 Connectors Connector 1 RING/CTS 2 DTR 6 DSR 3 XMT 5 RCV 4 XMTGND 4 RCVGND 5 RCVGND 3 XMTGND 6 RCV 2 XMT 7 DSR/DCD 1 DTR 8 RTS Figure 15 - MAXserver DEConnect Cable NOTE: If you have existing DEConnect cables that you want to use...

  • Page 69: Figure 16 - Octopus Cable With 50-Pin Telco Connector

    Getting Started with MAXserver Access Servers Figure 16 shows an octopus cable with a 50-pin Telco connector: Eight male RJ-45 50-pin Telco connector connectors (male or female) Figure 16 - Octopus Cable with 50-pin Telco Connector Figure 17 shows an octopus cable with a 36-pin female Telco DEConnect connector.

  • Page 70: Connecting To A Distribution Panel

    50-pin Telco connector to 8 male or female DB- 25 connectors. These cables are available from NBase-Xyplex in 3', 10', and 50' lengths. You can connect the unit to the distribution panel via the two octopus cables as shown in Figure 19.

  • Page 71: Figure 19 - Connecting A Maxserver To Db-25 Distribution Panel

    Getting Started with MAXserver Access Servers Octopus cable: 8 DB-25 MAXserver (male or female) to 50-pin 1620/1640 male Telco Octopus cable: 8 RJ-45 to 50-pin female Telco Distribution panel Figure 19 - Connecting a MAXserver to DB-25 Distribution Panel 0038...
  • Page 72 Figure 20 depicts the wiring that you would use to connect the serial port of a NBase-Xyplex unit to a modem or other DCE device. For simplicity, modular cables are shown in the figure; but there are other wiring options available with this cabling scheme.

  • Page 73: Figure 20 - Modular Cables For Connecting A Modem (6-Wire)

    DSR modem control signal for modem control, as well as DSRLOGOUT, SIGNAL CHECK, and hardware flow control applications. NBase-Xyplex 7-Wire Cabling This cabling scheme provides XMT, RCV, DCD/DSR, DTR, RING, and separate transmit and receive ground wires. This cabling is provided through RJ-45 connectors (pin 8 of the connector is not used).

  • Page 74: Figure 21 - Modular Cables For Connecting A Modem (7-Wire)

    (i.e., those which do not require RTS/CTS hardware flow control). Figure 22 shows the wiring for applications which require RTS/CTS flow control. You can purchase modular cables and adapters shown in the figure from NBase-Xyplex, or make your own cables based on the wiring diagram. Standard Modem Connection...

  • Page 75: Figure 22 - Modular Cables For Rts/Cts Flow Control (7-Wire)

    Adaptor Wiring - MX-320-0211 (Flow Control) Figure 22 - Modular Cables for RTS/CTS Flow Control (7-Wire) NBase-Xyplex 8-Wire Cabling This cabling scheme provides XMT, RCV, DCD/DSR, DTR, RTS, CTS/RNG, and separate transmit and receive ground wires. This cabling is provided through RJ-45 connectors.

  • Page 76: Figure 23 - Modular Cables For Connecting A Modem (Eight-Wire)

    Getting Started with MAXserver Access Servers This scheme is useful with the following applications: · Terminal emulation and file transfer applications, such as Kermit, Xmodem, Microphone, etc. · Applications such as SLIP and PPP using low speed modems. · Applications such as SLIP and PPP using high speed modems. ·...

  • Page 77: Figure 24 - Modular Cables For Rts/Cts Flow Control (Eight-Wire)

    NBase-Xyplex 3-Wire Cabling This cabling scheme provides XMT, RCV, and ground wires. This cabling scheme is used with NBase-Xyplex MX-TSERV-J16 and MX-TSRVL-J16 ACCESS SERVER cards. This wiring scheme can only be used for applications which do not require modem control signalling.

  • Page 78: Pin Assignments

    Getting Started with MAXserver Access Servers Pin Assignments Ethernet Transceiver Cable Figure 25 shows the standard 15-pin AUI connector signal assignments. Signal Chassis Ground Collision + Transmit + Chassis Ground Receive + Power Return Not Used Not Used Collision - Transmit - Chassis Ground Receive -...

  • Page 79: Rj-45 And Db-25 Pins

    Getting Started with MAXserver Access Servers 1 2 3 4 5 6 7 8 Signal Figure 26 - 10Base-T Connector Assignments RJ-45 and DB-25 Pins Figure 27 shows RJ-45 and DB-25 pin assignments. 1 2 3 4 5 6 7 8 8 7 6 5 4 3 2 1 RJ-45 Jack (Female)

  • Page 80: Using The Configuration Menu

    Getting Started with MAXserver Access Servers Using the Configuration Menu This section explains each parameter in an intialization record and how to change the configuration parameters for the access server using the Configuration Menu, or you can enter the appropriate command at the Xyplex prompt instead of using the menus.

  • Page 81: Loading Software Image And Parameters

    Getting Started with MAXserver Access Servers Loading Software Image and Parameters When you initialize an access server, it obtains the software load image and parameter file using the information in an initialization record. The NVS for the access server maintains three initialization records. The access server first attempts to load software using the information in the primary initialization record, if it is enabled.

  • Page 82: Loading Protocols

    TFTP, XMOP, BOOTP/TFTP, MOP, and RARP/TFTP. The protocols are: · Flash Card - For MAXservers, use FlashCard (card) to load image only. · Use XMOP for loading from a NBase-Xyplex load server. · Use MOP for loading from a VAX/VMS host. ·...

  • Page 83: Accessing The Configuration Menu

    Then all lights will go off in sequence from left to right. Then port lights 9 and 10 will go on (for MAXserver 1620/1640; ports lights 7 and 8 for the MAXserver 1608A, 1608B, and 1604). When this sequence has completed, you can release the RESET switch.

  • Page 84: About The Configuration Menu

    Getting Started with MAXserver Access Servers RETURN. The unit displays the menu shown in Figure 28. Welcome to the Configuration Menu. Access server Configuration Menu 1. Display unit configuration 2. Modify unit configuration 3. Initialize server and port parameters 4. Revert to stored configuration S.

  • Page 85: Displaying Initialization Records

    Getting Started with MAXserver Access Servers To Display the Unit Configuration Menu, complete the following steps: 1. Type 1 at the "Enter menu selection" prompt on the Access server Configuration Menu and press Return. The unit displays the Display Unit Configuration Menu, as shown in Figure 29. Display Unit Configuration Menu 1.

  • Page 86: Figure 30 - Sample Unit Configuration Display

    Getting Started with MAXserver Access Servers configuration. If there are still no service offers, the unit will wait and then try again, beginning with the primary configuration. Only the primary default initialization configuration is enabled at the factory. To display the settings for an initialization record, complete the following steps: Type 1, 2, or 3 at the Display Unit Configuration Menu.

  • Page 87: Displaying Miscellaneous Unit Configurations

    Getting Started with MAXserver Access Servers Displaying Miscellaneous Unit Configurations The Miscellaneous Unit Configuration option lets you view the current and new configuration information for the following configuration values: · Whether the unit is configured to load status messages · The amount of memory configured ·...

  • Page 88: Loading And Dumping Protocols

    Getting Started with MAXserver Access Servers Loading and Dumping Protocols Each initialization record has several loading and dumping protocols enabled by default if the access server attempts to obtain software and parameters from the network.The enabled protocols determine where the access server obtains the files.
  • Page 89 Getting Started with MAXserver Access Servers Table 5 - Default Protocols Software Load Image Parameter File Dump file CARD (default) NVS (default) XMOP XMOP XMOP BOOTP BOOTP BOOTP RARP RARP RARP DTFTP* *Not enabled by default. The access server first attempts to load software from the flash card using the CARD protocol, because this is the default.

  • Page 90: Modify Unit Configuration

    Getting Started with MAXserver Access Servers because NBase-Xyplex flash cards do not function as dump servers due to size limitation. The NVS protocol is also not applicable to load image files. The XMOP and MOP Protocols The XMOP and MOP protocols look for a software load image file, a parameter file, or a dump server.

  • Page 91: Figure 32 - The Modify Unit Configuration Menu

    Getting Started with MAXserver Access Servers To modify the access server configuration, complete the following steps: 1. Type 2 at the "Enter menu selection" prompt of the Access server Configuration Menu. The unit displays the Modify Unit Configuration Menu, as shown Figure 32. Modify Unit Configuration Menu 1.

  • Page 92: Creating A Customized Configuration

    Getting Started with MAXserver Access Servers ‘N’ - Disables the specified initialization configuration and lets you create your own configuration. See “Creating a Customized Configuration” to continue. Creating a Customized Configuration This section explains how to create a custom configuration for the MAXserver access server.
  • Page 93 Getting Started with MAXserver Access Servers The following table lists the factory-default protocol settings: Table 6 - Default Protocols Software Load Image Parameter File Dump file CARD XMOP XMOP XMOP BOOTP BOOTP BOOTP RARP RARP RARP DTFTP* *Not enabled by default. Software Load Images The following load image protocols are enabled at the factory.
  • Page 94 Getting Started with MAXserver Access Servers The following table lists the six methods available for loading images. Table 7 - Image Loading Methods ¼ ¼ Method Loads softare from Flash card. TFTP. Xyplex MAXserver Manager or from another unit that has a flash card and the proper load image.

  • Page 95: Defining Parameter Loading Methods

    Getting Started with MAXserver Access Servers Defining Parameter Loading Methods This section describes how to specify the unit’s parameter loading methods. All MAXserver units are configured at the factory to store configuration data (parameters) locally in Non-volatile storage (NVS). Alternatively, you can use DEFINE SERVER commands to change the parameter loading method.

  • Page 96: Defining Dumping Methods

    Getting Started with MAXserver Access Servers image. From the MOP -DEC Maintenance Operations Protocol (DEC MOP) loader protocol. B (Bootstrap Protocol) At a BOOTP/TFTP host. R (RARP From Reverse Address Resolution Protocol (RARP/TFTP). 1. Select specific protocol(s) by removing letters from or adding letters to the brackets.
  • Page 97 Getting Started with MAXserver Access Servers Table 9 - Dumping Methods Value Description Dumps its memory contents to a MAXserver Manager when a crash occurs (you cannot enable dumping to a flash card). Dumps memory contents via the DEC MOP loader protocol.
  • Page 98 Getting Started with MAXserver Access Servers This section describes how to define the image filename if you selected CARD, XMOP or MOP as the loading method. Once you have selected the dumping methods and pressed RETURN, the unit displays the following prompt (if you selected CARD, XMOP or MOP as the unit’s loading method).

  • Page 99: Defining Ip Addresses

    VAX/VMS load server, or via client entries on a Xyplex loader. This is the default. 2 through 4 Reserved for use by NBase-Xyplex Requires a load server to ignore the load request -- unless the load server's client database contains a node entry for the requesting access server.

  • Page 100: Miscellaneous Unit Configuration

    Getting Started with MAXserver Access Servers 1. Enter the access server’s IP address, or press RETURN to accept the default address, 0.0.0.0. You must supply a non-zero IP address if you have specified all image loading protocols or DTFTP as an image loading method.
  • Page 101 Getting Started with MAXserver Access Servers Enabling/Disabling Status Message Display To enable or disable loading status messages, complete the following steps: 1. Type M at the Enter Menu Selection prompt on the Access server Configuration menu and press RETURN. The unit prompts: DISPLAY LOAD STATUS MESSAGES (Y,N) [Y]: 2.

  • Page 102: Resetting The Unit's Load And Dump Protocols To Factory Defaults

    Getting Started with MAXserver Access Servers instructions later in this guide to install and remove SIMM modules. The unit automatically detects added memory. Therefore, you do not need to increase the "installed memory" value when you install additional memory. If you want to increase the value, install the additional memory first. If you do, the unit will generate the following warning message: WARNING: AFTER SAVING THE NEW CONFIGURATION, YOU MUST...
  • Page 103 Getting Started with MAXserver Access Servers To choose this option, complete the following steps: 1. Enter ROM configuration mode. At the # prompt, enter the word access. The Terminal Server Configuration Menu is displayed. 2. Choose Option 2 (“Modify Unit Configuration”) from the Terminal Server Configuration Menu.

  • Page 104: Initializing Server And Port Parameters

    Getting Started with MAXserver Access Servers Initializing Server and Port Parameters The Initialize Server and Port Parameters option instructs the operating software, once loaded, to use factory default values for all server and port parameters. All current server and port parameters will be lost when you exit from the menu (using Option S "Exit saving configuration changes").

  • Page 105: Exit Saving Configuration Changes

    Getting Started with MAXserver Access Servers 2. Type N and press RETURN to return to the Configuration menu, or type Y and press RETURN. The unit displays the following message: CONFIGURATION RESET TO STORED VALUES. (TYPE ANY KEY TO CONTINUE) 3.
  • Page 106 Getting Started with MAXserver Access Servers The Exit Without Saving Configuration Changes option on the Configuration menu lets you exit without saving the configuration changes that you have made (i.e., use the configuration that was last saved). 1. To select this option, type X at the "Enter menu selection" prompt. If you have made changes, the configuration menu prompts: Exit without saving changes (Y/N) [N]? 2.

  • Page 107: Command Line Interface

    Getting Started with MAXserver Access Servers Command Line Interface This section describes the commands you can use to configure the MAXserver from the command line: · Viewing Initialization Parameters · Changing the name of the software image file · Assigning IP addresses to the network host, access server, gateway, and the network host where the image file resides ·...

  • Page 108: Figure 33 - Sample Primary Initialization Record Display

    Getting Started with MAXserver Access Servers Figure 33 shows a sample display. Primary Record: Enabled Internet Load Address 0.0.0.0 Internet Load Host 0.0.0.0 Internet Load Gateway 0.0.0.0 Internet Load File None Software: XPCSRV20 Image Load Protocols Enabled: Card, XMOP, MOP, BOOTP, RARP Dump Protocols Enabled: XMOP, MOP, BOOTP, RARP Parameter Protocols Enabled:...

  • Page 109: Enabling/Disabling Image And Parameter Protocols

    Getting Started with MAXserver Access Servers Enabling/Disabling Image and Parameter Protocols Use the following command to enable or disable software load image protocols and operational parameter protocols: Use this command to specify one or all load protocols to use when the access server searches for a software load image file or a parameter file.
  • Page 110 Getting Started with MAXserver Access Servers Syntax DEFINE SERVER LOAD[ record ][ usage ]PROTOCOL[ protocol-name ][ENABLED] [DISABLED] Where Means record Use one or more of the following initialization records: PRIMARY SECONDARY TERTIARY The PRIMARY initialization record is the default. usage Use one of the following keywords, which indicate whether you are specifying a protocol for a software load image or a parameter file:...
  • Page 111 Getting Started with MAXserver Access Servers protocol Specify one of the following keywords which represent different protocols: Protocol Means NonVolatile Storage protocol for the parameter file CARD Local memory card protocol for the load image XMOP Xyplex MOP Protocol Digital Equipment Corporation Maintenance Operations Protocol BOOTP Bootstrap protocol...

  • Page 112: Naming Load Files

    Getting Started with MAXserver Access Servers ENABLED Enable the protocol in the initialization records you specify. You can enable only one protocol in the command line, unless you use the keyword ALL to enable all protocols. DISABLED Disable the protocol in the initialization records you specify.

  • Page 113: Retrieving Image Files From Host

    Use this command to retrieve a load image from a host on the LAN to a flash card in an access server, either through TFTP or XMOP (use XMOP to get the image from another NBase-Xyplex unit). GET CARD LOAD FILE [ image-name ] ADDRESS [ ip-address ]...

  • Page 114: Assigning Ip Addresses

    Getting Started with MAXserver Access Servers Example The following command shows how to disable RARP as a dump protocol in the primary initialization record: XYPLEX>> DEFINE SERVER DUMP PRIMARY PROTOCOL RARP DISABLED Assigning IP Addresses You need to configure the following IP addresses to establish Internet access for MAXservers.
  • Page 115 Getting Started with MAXserver Access Servers Example The following example shows the command that specifies an IP address for an Internet load host in the primary initialization record: DEFINE SERVER LOAD PRIMARY IP HOST 140.179.119.3 Access Server IP Address The Internet load address specifies the Internet address for the access server.
  • Page 116 Getting Started with MAXserver Access Servers Example The following example specifies the Internet Load File in the primary initialization record: XYPLEX>> DEFINE SERVER LOAD PRIMARY INTERNET FILE "/USR/XYPLEX/IMAGES/XPCSRV20.SYS" Internet Load Gateway The Internet load gateway specifies the IP address of a gateway on the network which the access server uses to gain access to the Internet load host.

  • Page 117: Resetting Initialization Parameters To Default Values

    Getting Started with MAXserver Access Servers Resetting Initialization Parameters To Default Values If you want to reset the values of parameters in one or more initialization records after you have changed them, you can do so with one command, rather than resetting each value individually. Initialization parameters include the status of the initialization record, the protocols, the CARD/XMOP/MOP load image filename, and the Internet settings for DTFTP loading.

  • Page 118: Displaying The Software Load Host

    Getting Started with MAXserver Access Servers Use the following command to display the current parameters: LIST|MONITOR SERVER LOADDUMP [ RECORD |ALL] CHARACTERISTICS Example This sample display shows the primary initialization record. XYPLEX> LIST SERVER LOADDUMP PRIMARY CHARACTERISTICS Primary Record: Enabled Internet Load Address 140.179.80.133 Internet Load Host...

  • Page 119: Protocols

    Getting Started with MAXserver Access Servers By default, all available dump protocols and parameter file protocols are enabled, and all available software load image protocols are enabled except DTFTP. The access server attempts to load software using the CARD protocol first, because this is the default.
  • Page 120 Getting Started with MAXserver Access Servers Enabling/Disabling Loading Protocols The DEFINE SERVER LOAD PROTOCOL command specifies one or all load protocols to use when the access server searches for a software load image file or a parameter file. You specify whether the protocol applies to the software load image or the parameter file in the command line.
  • Page 121 Getting Started with MAXserver Access Servers This example enables MOP as the protocol to use when loading the parameter file from the primary initialization record. XYPLEX>> DEFINE SERVER LOAD PRIMARY PARAMETERS PROTOCOL MOP ENABLED This example disables the RARP protocol for use when loading the parameter file from the secondary initialization record.
  • Page 122 Getting Started with MAXserver Access Servers Examples This command disables the primary initialization record. With this record disabled, the access server first attempts to load or dump using information in the secondary initialization record. XYPLEX>> DEFINE SERVER LOADDUMP PRIMARY DISABLED This command enables all initialization records.

  • Page 123: Setting Up Maxserver Ports For Out-Of-Band Management Of Console Port Devices

    Getting Started with MAXserver Access Servers Setting Up MaxServer Ports for Out-of-band Management of Console Port Devices This section describes how to set up MaxServer ports for out-of-band management of console port devices. NOTE: The commands described in this section can only be executed in Privileged mode.
  • Page 124 Getting Started with MAXserver Access Servers attached console port device. 5. Set up the flow control for the destination port: DEFINE/SET PORT < port-number > FLOW CONTROL < flow-control-setting > The flow control setting must match the flow control setting on the attached console port device.
  • Page 125 Getting Started with MAXserver Access Servers After you have completed this procedure, you are ready to access the out-of- band management console port. Refer to the following section, “Accessing the Out-of-band Management Console Port”, for more information on accessing the out-of-band management console port. 0038...

  • Page 126: Accessing The Out-Of-Band Management Console Port

    Getting Started with MAXserver Access Servers Accessing the Out-of-band Management Console Port There are two methods for accessing the out-of-band management console port. This sections describes both methods. Accessing from an Ethernet-attached Station Use the following command to access the out-of-band management console port from an Ethernet-attached station: telnet 192.168.5.1:<...
  • Page 127 Getting Started with MAXserver Access Servers 5. Enter the following command: TELNET 192.168.5.1: < logical-port-number > In the above command, logical-port-number is the logical port number of the out-of-band management console port. To determine the logical port number, multiple the physical port number by 100 and add 2,000. For example, the logical port number for physical port number 1 is 2100.

  • Page 128: Troubleshooting

    Getting Started with MAXserver Access Servers Troubleshooting Refer to this section if you experience a problem with your MAXserver. This section describes: · How to troubleshoot startup and loading problems · What to do if the LAN light on the front panel goes out ·...

  • Page 129: Startup Error Codes

    Getting Started with MAXserver Access Servers 13. The CARD light goes ON for approximately 15 seconds if the unit is loading from a flash card. (The MAXserver is accessing the flash card. Do not remove the card while the CARD light is ON.) 14.

  • Page 130: Figure 35 - Sample Error Code Display

    Getting Started with MAXserver Access Servers Self-test failure occurs. LEDs flash 10 times, very quickly. User records First Error Code error code 78 LEDs flash sequentially User records Second Error Code error code 24678 Sequence repeats continuously 0 = Off 1 = On Figure 35 - Sample Error Code Display 0038...

  • Page 131: Common Error Codes

    Getting Started with MAXserver Access Servers Write down the numbers of the error code (the lights that are ON) and contact your NBase-Xyplex Customer Support representative. (In the U.S., call 1-800-435-7997. For International calls, the number is 978-952-4888). Your representative will provide further instructions on how to handle the condition.

  • Page 132: Power Up And Re-Initialization Problems

    Getting Started with MAXserver Access Servers XYPLEX>>INITIALIZE DELAY 0 Power Up and Re-initialization Problems The following list describes the problems you might encounter when you power up or re-initialize a MAXserver. The list includes descriptions of correct operations and possible solutions. CARD light does not go ON Problem: You are trying to load from a Memory card and the CARD light does not go ON.

  • Page 133: Network Loading Problems

    Getting Started with MAXserver Access Servers Use the following command to display the contents of the SYSTEM directory: SHOW SYSTEM PARAMETERS Network Loading Problems Problem: The MAXserver does not appear to load from the network, or is slow to load from the network. Correct Operation: The load server downloads a software image and (optionally) parameters to the MAXserver, over the network, whenever the unit is powered on or re-initialized.

  • Page 134: Loading Problems

    If this message does not appear after you type several <RETURN>s, the MAXserver unit could be at fault. Call NBase-Xyplex Customer Support. (In the U.S., call 1-800-435-7997. For International calls, the number is 978- 952-4888).

  • Page 135: Load Server Errors

    Getting Started with MAXserver Access Servers Solution: Check that the MAXserver is in the RUN state and that the Ethernet transceiver cable or 10BASE-T network cable is properly installed. Load Server Errors A message similar to the following one is displayed if the MAXserver has received a load offer from a load server: EVALUATING SERVICE OFFERS If you typed a <CTRL><T>...
  • Page 136 Error: Error Server xx-xx-xx-xx-xx-xx; File error: not executable. Problem: No 680xx CPU identifier appears in the file header. This is a NBase-Xyplex file, but it cannot be executed by the server. Solution: Resolve this problem by installing the proper file in the load server.
  • Page 137 (approximately 60 bytes) to a server that is configured to accept a dump file. The dump file can be analyzed by NBase-Xyplex to assist you in resolving the fault. Call NBase-Xyplex Customer Support for assistance.
  • Page 138 Getting Started with MAXserver Access Servers This type of message displays while the MAXserver waits for a response to its dump request. If this message displays for more than 30 seconds after you type several <RETURN>s, the MAXserver is not configured on a dump server, or the MAXserver cannot communicate to a dump server.
  • Page 139 Getting Started with MAXserver Access Servers If a failure occurs during the dump process, the MAXserver will abort the dump and attempt to dump to the next dump server, until the dump server list is exhausted. After the dump process completes, the MAXserver selects the load server with the next highest merit value on the load offer list.
  • Page 140 Getting Started with MAXserver Access Servers Link L1 refers to the Ethernet transceiver cable or 10BASE-T network cable; that is, the server is loading parameters via the LAN. If the message count remains at zero after you type several <RETURN>s, the load server is properly configured, but does not have a defined parameter file.
  • Page 141 If none of these checks indicate a problem and the LAN light is still not ON, contact your NBase-Xyplex Customer Support representative for assistance. (In the U.S., call NBase-Xyplex Customer Support at 1-800-435-7997. For International calls, the number is 987-952-4888).

  • Page 142: Simms Installation

    The MAXserver accepts 30-pin 70 ns. (or faster) 1M x 8 SIMMs with tin contacts. (Do not use SIMMs with gold contacts.). The order code for a 2MB SIMM memory upgrade kit is MX-500-5744. Contact your NBase-Xyplex sales representative to order this kit.
  • Page 143 30 pins, 80 ns or faster, 1M x 8 SIMMs with tin contacts (NOT GOLD). · Manufacturer's Part No. NEC MC-421000A8B-80OKIMSC2313A-80YS8 Toshiba THM81000AS-80 Samsung KMM581000A-8 Micron MT8D18M-8 Mitsubishi MH1M08B0J-8 Fujitsu MB85230A-80PS NBase-Xyplex offers SIMM Upgrade kits for all MAXserver units. Contact your NBase-Xyplex sales representative for ordering information. 0038...

  • Page 144: Maxserver Memory Requirements

    Getting Started with MAXserver Access Servers MAXserver Memory Requirements Each SIMM provides 1 Megabyte of memory. SIMMs must be installed or removed in pairs; you can install either two, four, or six SIMMs (i.e., 2, 4, or 6 Megabytes of memory). This means that the MAXserver can be configured with a total of 4, 6, or 8 Megabytes of memory.

  • Page 145: Figure 37 - Removing The Screws Securing The Cover

    Getting Started with MAXserver Access Servers 2. Set the MAXserver on a grounded workbench or other flat, stable surface. 3. Attach an anti-static strap to your wrist, and connect the strap to a well grounded object. If a well grounded object is not available, connect the strap to the MAXserver chassis after you remove the cover.

  • Page 146: Figure 38 - Location Of Simm Sockets

    Getting Started with MAXserver Access Servers (REAR) Power Supply Memory Card Slot Retainers SIMM Sockets Figure 38 - Location of SIMM Sockets 0038...
  • Page 147 Getting Started with MAXserver Access Servers 6. Install two SIMMs at a time, and install them into the sockets in the following order: 1 and 2, then 3 and 4, then 5 and 6. (It is easier to install each pair of SIMMs by installing the SIMM in the odd-numbered sockets first.) 7.

  • Page 148: Figure 39 - Inserting Simm Into Socket

    Getting Started with MAXserver Access Servers 1. Insert SIMM at 30° angle. Press down. 2. Press forward, until SIMM snaps into place. Figure 39 - Inserting SIMM into Socket 10. Make sure that the SIMMs are secure within the retainers. 11.

  • Page 149: Verifying Memory Installation Using Commands

    Getting Started with MAXserver Access Servers 12. Return the unit to the rack or flat surface from which you removed it, and plug it back in. 13. When you apply power, the MAXserver performs a self test of its circuitry and then proceeds to load its software. When the unit has finished loading its software, the RUN light flashes slowly and the LAN light flashes as Ethernet packets are received.
  • Page 150 Getting Started with MAXserver Access Servers the memory installation by following these steps: 1. Using a straightened paper clip, press the MAXserver RESET switch once to enter reset mode. All lights on the front panel should illuminate. 2. Press the RESET switch again, and hold the switch in. With the switch held in, observe the port lights.

  • Page 151: Figure 40 - Maxserver Access Server Configuration Menu

    Getting Started with MAXserver Access Servers Welcome to the Configuration Menu. Access server Configuration Menu 1. Display unit configuration 2. Modify unit configuration 3. Initialize server and port parameters 4. Revert to stored configuration S. Exit saving configuration changes X. Exit without saving configuration changes Enter menu selection [X]: Figure 40 - MAXserver Access server Configuration Menu 5.

  • Page 152: Removing Simms

    Getting Started with MAXserver Access Servers 6. Type 'M' and press <RETURN>. The unit displays a screen similar to Figure 42. Stored Configuration New Configuration Load status messages: Enabled Enabled Memory installed: 4 Megabytes 4 Megabytes (Found 4 Megabytes) (Type any key to continue) Figure 42 - Sample Miscellaneous Configuration Display The display indicates the amount of installed memory detected by the MAXserver.

  • Page 153: Removing Simms From The Maxserver

    Getting Started with MAXserver Access Servers To remove memory from the MAXserver, complete the following steps: 1. Select Option 2 from the Configuration Menu and press <RETURN>. The unit displays the Modify Unit Configuration Menu. 2. Select option M and press <RETURN>. The MAXserver displays a series of prompts.

  • Page 154: Figure 43 - Removing Simms

    Getting Started with MAXserver Access Servers 2. To remove the SIMMs from the sockets, pull the retainers that hold the SIMM outward (see Figure 43). Pull retainers outward. Figure 43 - Removing SIMMs 3. Pull the SIMM toward you, then up. (Basically, you reverse the steps shown in Figure 37.) 4.

  • Page 155: Technical Specifications

    MAXserver 1604/1608/1620 - 50 to 115.2 Kbps MAXserver 1640 - 50 bps to 56.7 Kbps Number of Serial MAXserver 1604 - 4 ports Ports MAXserver 1608A/B - 8 ports MAXserver 1620 - 20 ports MAXserver 1640 - 40 ports 0038...
  • Page 156 25W, 110Btu/hr 0.7A at 120V (typ), 0.3A at 220V 1608B/1604 (typ) Minimum Software Access Server Software, V5.3 or later for Requirements MAXserver 1608A, 1620 and 1640. V6.0.3 or later for MAXserver 1604 and 1608B. Ethernet Interface Ethernet/IEEE 802.3 Connection -- 10BASE-T or AUI Transceiver 0038...

  • Page 157: Index

    Index BOOTP enabling as a dump protocol, 119 bootstrap protocol (BOOTP), 16 10Base-T connector, 25 broadcasts 10Base-T connectors, 79 for delays, 57 10Base-T network cable, 20 10BASE-T network cable, 141 cables, 21 checking connections, 140 AC line cords, 26 connecting to RJ-45 jacks, 29 AC power outlets, 26 DEConnect compatible, 68 AC power receptacle, 26...
  • Page 158 Index (continued) communication speeds, 15 DEConnect cabling, 68 communication speeds. See also baud DEConnect connector, 69, 70 rates., 140 DECserver 200 load file, 136 configuration default prompt settings, 46 current unit settings, 85 default settings, 30 customizing, 92 defaults reverting to last saved values, 104 gateway IP address, 116 using ControlPoint, 18 image protocols, 93...
  • Page 159 Index (continued) dump files naming conventions, 98 problems with, 138, 139 TFTP loading, 100 dump protocols, 88, 108, 113 flash cards, 51 enablind/disabling, 119 areas, 113 dump requests, 138 copying contents to another card, 53 dump servers, 137 current settings, 53, 54 dumping methods, 96, 97 deleting contents, 53 loading images, 55...
  • Page 160 Index (continued) image load methods, 89 network hosts, 114 image loading IP Addresses terminating, 113 for internet access, 30 image loading methods, 92, 94 IP load address, 115 INIT DELAY command, 33, 57, 58 IP load file, 115 initialization records, 81 IP load hosts, 114 initialization records creating, 85...
  • Page 161 Index (continued) description of, 20 modify unit configuration, 91 load servesr, 133 modular adapter, 68 loading MONITOR PARAMETER SERVER problems with, 134 command, 34 loading image files, 55, 56 MOP (Maintenance Operations loading parameters, 139 Protocol), 98 loading protocols, 82 MOP loading, 90 loading the image files, 52 MOP protocol, 16...
  • Page 162 Index (continued) parameter load requests, 139 privileged mode, 38 parameter loading methods, 95 privileged password, 43 parameter server, 139 privileges, 37, 49 parameter servers description of, 48 loading from a network host, 95 restoring, 48 names and locations, 119 prompts names and locations, 88 changing defaults, 46 parameter service, 90...
  • Page 163 Index (continued) reset initialization records, 91 software filenames, 108 RESET switch, 34, 35, 83, 150 software loading, 133 resetting parameters, 102, 117 software requirements, 15 Reverse Address Resolution Protocol speeds, 155 (RARP), 16 cable lengths, 155 reverse octopus cable, 70 startup and loading problems, 128 RJ-45 connectors, 63, 68 status messages, 81...
  • Page 164 Index (continued) XMT, RCV, DCD, DTR, RING, 72 wiring schemes, 60 XMOP loading, 90 crossover cables, 64 XMOP,, 89 for RJ-45, 63 XPCSRV20 images, 52 straight-through cables, 64 wrist straps, 20 0038...

This manual is also suitable for:

Maxserver 1608bMaxserver 1604Maxserver 1640Maxserver 1620

Table of Contents