Table of Contents
Advertisement
Inverter
tics
> Statistics
onsumpti.
> Lifetime
ufficien.
> Partial
from grid
> Today
to grid
> Last 7 days
to load
> Last 30 days
to load
> Last 365 days
r.
> User Period
gs
> Settings
d 0000
Password 0000
me
> Vstart
sh
> Input mode
S485 com
> Input UV Delay
y Select
> Service
ssword
> Remote ON/OFF
> MPPT Scan
*
ate Info
> Power Limit.
Policy
> Reactive Power
es
> Autotest
> Alarms
> Backup
> Info
> Part No.
> Serial No.
> Firmware
• Configurable alarm with reset at the end of the alarm signalling
process (display text "Alarm Conf.")
INVERTER RUN
Display
Relay State: Idle
SELECTED
> Settings
ERROR/WARNING
OCCURENCY
Password 0000
> Backlight
ERROR MESSAGE
t=15s
> Contrast
Relay State: Switched
> Buzzer
GRID RECONNECTION
t=based on Country Standard
> Power Graph
Relay State: Idle
> Language
ERROR/WARNING
Yes
STILL
PRESENT
Selectable alarms for which the relay is activated
E001
E002
E007
E009
E014
E015
E020
E021
E026
E027
E032
E033
E046
E050
E057
E058
E089
W001
**
W006
W007
W047
W048
For the configurable relay operating mode "Alarm Conf.", the following
considerations are valid:
If the alarm condition is persistent, the alarm contact cyclically switches
from its resting state to its activated state.
In the presence of W002 signalling (Input UV – input voltage below the
limit of operation), the alarm contact switches to then reset itself at the
end of the alarm signal. This means that during the reduced input voltage
(display message "Waiting Sun") the alarm contact remains in its resting
position.
In the presence of W003, W004, W005, W006, W007 signalling, the
alarm contact switches to then reset itself at the end of the alarm signal.
- 135 -
Скачано с сайта интернет магазина https://axiomplus.com.ua/
****
Meter
N.C.
The relay is activated (status: switched)
N.O.
whenever an error (code Exxx) or a war-
> Settings
ning (code Wxxx) is among those se-
lected from the list in the dedicated
Password 0000
submenu Alarm Config. The contact re-
> Meter model
turns to its resting position when the alarm
N.C.
> Meter Address
signal ends, i.e. before the inverter checks
N.O.
the grid after the alarm state. This is be-
> Meter com
cause grid control state is not an alarm
> Info
state but a state of normal operation.
N.C.
> Type
N.O.
> Part No.
No
> Serial No.
> FW Rel.
> Measures
> Voltage
E003
E004
> Active Power
E010
E011
E016
E017
> Line current
E022
E023
> Load current
E028
E029
E034
> Frequency
E035
E053
E054
E077
E078
W002
W003
W009
W011
W051
W058
7 - Operation
****
Battery
> General
> Settings
Password 000
> Battery Mo
> Battery Pa
> Info
> Nom. Cap
> Measures
> Ibat
> Vbat
> Pbat
> RE
E005
E006
> SOC
E012
E013
E018
E019
> SOH
E024
E025
> RT
E030
E031
E036
> Pack 1
E037
E055
E056
> Statistics
E081
E084
> Energy disc
W004
W005
W015
W046
> E-day
W059
> E-7d
> E-30d
> E-365
> E-tot
> Settings
Password 000
> Pack 1 ena
> Smoke Sens
> Info
> Device Nam
> Serial No.
> FW Rel.
> Nom. Capac
Advertisement
Table of Contents
