Specifications; Electrical Data; Line Power Supply 1X200-240 V Ac - Danfoss VLT AQUA Drive FC 202 Design Manual

Specifications

7 Specifications

7.1 Electrical Data

7.1.1 Line Power Supply 1x200–240 V AC
Type designation
Typical shaft output [kW]
Typical shaft output at 240 V [hp]
Protection rating IP20/Chassis
Protection rating IP21/Type 1
Protection rating IP55/Type 12
Protection rating IP66/NEMA 4X
Output current
7 7
Continuous (3x200–240 V) [A]
Intermittent (3x200–240 V) [A]
Continuous kVA at 208 V [kVA]
Maximum input current
Continuous (1x200–240 V) [A]
Intermittent (1x200–240 V) [A]
Maximum pre-fuses [A]
Additional specifications
Maximum cable cross-section (line power, motor,
brake)
[mm 2 ] ([AWG])
Maximum cable cross-section
disconnect switch
[mm2] ([AWG])
Maximum cable cross-section
without disconnect switch
[mm2] ([AWG])
Cable insulation temperature rating [°C (°F)]
Estimated power loss
Efficiency 5)
Table 7.1 Line Power Supply 1x200–240 V AC, Normal Overload 110% for 1 Minute, P1K1–P22K
148
®
VLT
2)
for line power with
2) for line power
3) at rated maximum load [W] 4)
Danfoss A/S © 09/2014 All rights reserved.
AQUA Drive FC 202
P1K1 P1K5 P2K2 P3K0
1.1 1.5 2.2 3.0
1.5 2.0 2.9 4.0
A3 - - -
- B1 B1 B1
A5 B1 B1 B1
A5 B1 B1 B1
6.6 7.5 10.6 12.5
7.3 8.3 11.7 13.8
2.4 2.7 3.8 4.5
12.5 15 20.5 24
13.8 16.5 22.6 26.4
20 30 40 40
0.2-4 (4-10)
16 (6) 16 (6) 16 (6) 16 (6)
16 (6) 16 (6) 16 (6) 16 (6)
75 75 75 75
(167) (167) (167) (167)
44 30 44 60
0.98 0.98 0.98 0.98
P3K7 P5K5 P7K5 P15K
3.7 5.5 7.5 15
4.9 7.5 10 20
- - -
B1 B1 B2 C1
B1 B1 B2 C1
B1 B1 B2 C1
16.7 24.2 30.8 59.4
18.4 26.6 33.4 65.3
6.0 8.7 11.1 21.4
32 46 59 111
35.2 50.6 64.9 122.1
60 80 100 150
10 (7) 35 (2) 50 (1/0)
16 (6) 16 (6) 25 (3) 50 (1/0)
16 (6) 16 (6) 25 (3) 50 (1/0)
75
75 (167) 75 (167) 75 (167)
(167)
74 110 150 300
0.98 0.98 0.98 0.98
P22K
22
30
- -
C2
C2
C2
88
96.8
31.7
172
189.2
200
95 (4/0)
2 x 50 (2
9)
x 1/0)
10)
95 (4/0)
75 (167)
440
0.98
MG20N622