Ikegami HDK-790GX Operation Manual page 89

3
On MENU (3/4), turn the MENU SELECT switch to
position the cursor on "LENS SELECT," and press
the MENU SELECT switch.
The submenu is displayed.
4
Set "NUMBER", "NAME" and "EXTENDER".
Refer to the explanation of corresponding item for how
to set each data.
NO.1 is selected here as an example.
Caution:
If a new le is created with the same le number as an existing le, the data will be overwritten and the old data will be lost.
5
Turn the MENU SELECT switch to position the
cursor on "FILE SET," and press the MENU
SELECT switch.
The cursor moves to the mode selection column.
6
Turn the MENU SELECT switch to select the set
value, and press the MENU SELECT switch.
The value is con rmed, and either of the following
messages is displayed at the bottom of the screen:
- LENS No. x
- PUSH SET -> START : Displayed and ashes when
Go to Step 7 when "AUTO" is selected.
When "MANUAL" is selected, go to Step M1 to obtain
the model name of the lens after lens le items such as
GAIN/FLARE/GAMMA are adjusted by MCP, etc.
7
Press the MENU SELECT switch.
The lens le is created.
8
Set the S11-4 DIP switch of the MPU module back to "OFF".
Note:
- When the camera is powered OFF, the FILE SET settings are turned OFF.
- Before creating lens les, prepare all the lenses to use. Then, create the les under the same condition at a time. If the conditions are
changed, the setting cannot be accurate. Lens les memorize a difference in level between lenses. If the lighting or chart is changed,
it cannot tell whether it is the lighting error, chart error, or lens error.
: Displayed when "MANUAL"
is selected.
"AUTO" is selected.
HDK-790GX 1403 VER1 (U)
5.2 Settings from the Menu
＊＊＊ ＭＥＮＵ （３／４） ＊＊＊
▲
ＳＣＡＮ ＦＯＲＭＡＴ ＳＥＬＥＣＴ
ＣＰＵ ＳＹＳＴＥＭ ＣＯＮＴＲＯＬ
ＡＵＴＯ ＩＲＩＳ ＳＥＴ
ＡＷＢ／ＡＢＢ ＭＯＤＥ
ＬＥＮＳ ＳＥＬＥＣＴ
ＬＥＶＥＬ ＡＤＪＵＳＴ
ＰＲＯＣＥＳＳ ＭＯＤＥ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＭＥＮＵ ＭＯＤＥ
ＬＥＮＳ ＳＥＬＥＣＴ
ＮＵＭＢＥＲ ＮＯ．１
ＮＡＭＥ （ ）
（ＡＢ４０Ｘ１０ ＡＢＣＤ ）
ＥＸＴＥＮＤＥＲ ＯＦＦ
ＡＵＴＯ ＳＥＬ ＯＦＦ
ＦＩＬＥ ＳＥＴ ＯＦＦ
ＬＥＮＳ ＴＹＰＥ ＊＊＊
ＡＵＴＯ Ｘ０．８ ＣＯＮＶ ＯＦＦ
Ｘ０．８ ＣＯＮＶ ＣＯＮＴ ＯＦＦ
ＬＥＮＳ ＳＥＲＩＡＬ Ｉ／Ｆ ＯＦＦ
ＦＩＬＥ ＳＥＴ ＯＦＦ
ＬＥＮＳ ＮＯ．１
ＰＵＳＨ ＳＥＴ→ＳＴＡＲＴ
③
Position the flashing
cursor on "LENS
SELECT" and confirm.
⑤
5
Position the cursor on
"FILE SET" and
confirm.
⑥
Select the set value
and confirm.
⑦
Either message is
displayed or flashes.
77