Xerox Phaser 3635MFP Service Manual page 204

iv. Low
v. A numeric value with up to four digits e.g. 0020.
6. Touch a component in the component table and then touch Stop to stop that component.
To stop all components touch Stop All.
7. Touch Exit to close the Component Control window.
8. To exit diagnostics mode, GP 1 Diagnostics
3550 Component Control
1. Enter diagnostics, GP 1 Diagnostics
2. For fax component control:
a. Select Fax Diagnostics and press the OK key.
b. Select EDC Mode and press the OK key.
c. Select DC330 CC and press the OK key.
3. For machine component control:
a. Select Machine Diagnostics and press the OK key.
b. Select EDC Mode and press the OK key.
c. Select DC330 Component Control and press the OK key.
4. Select the required control code and press the OK key.
5. Press the OK key to start a component. Press the Stop key to stop the component.
6. Press the Return key to close the Component Control window.
7. Exit diagnostics mode, GP 1 Diagnostics
Input Codes
Table 1 Input codes 01
Code Displayed Name Description
01-100 Front cover inter- Front cover interlock switch (S01-
lock 100), detects if the side cover is
open.
Table 2 Input codes 05
Code Displayed Name Description
05-100 DADF Doc. Detect DADF document detect sensor
Sensor (Q05-100), detects if a document is
present.
05-120 DADF Paper DADF paper length sensor (Q05-
Length Sensor 120), (Q05-100), detects if a docu-
ment is present.
05-130 DADF Registration DADF document registration sen-
Sensor sor (Q05-130), detects if a docu-
ment is present.
05-140 DADF Scan Sensor DADF document scan sensor
(Q05-140), detects if a document is
present.
05-160 DADF Door Open DADF door open sensor (Q05-
Sensor 150), detects if the DADF door is
open.
Phaser 3635MFP/WorkCentre 3550
Entry, select the Call Close Out button.
Entry.
Entry.
General
Closed = front cover closed
Opened = front cover
opened
General
High = document present
Low = no document
High = document present
Low = no document
High = document present
Low = no document
High = document present
Low = no document
High = door open
Low = door closed
Code Displayed Name Description
06-110 LSU Motor Ready Detects if the LSU motor (MOT06-
100) is running at normal speed.
Code Displayed Name Description
07-110 T1 Paper Empty Tray 1 paper empty sensor (Q07-
Sensor 110), detects if there is paper
present in tray 1.
07-210 T2 Paper Empty Tray 2 paper empty sensor (Q07-
Sensor 210), detects if there is paper
present in tray 2.
07-510 Bypass Paper Bypass paper present sensor (Q07-
Empty Sensor 510), detects if there is paper
present in the bypass tray.
Code Displayed Name Description
08-100 Feed Sensor Detects when the lead edge of the
paper is at the feed sensor (Q08-
100).
08-500 Regi. Sensor Detects when the lead edge of
paper is at the registration sensor
(Q08-500).
08-600 Exit Sensor Detects when the lead edge of
paper is at the fuser exit sensor
(Q08-600).
08-700 Duplex Jam 1 Sen- Detects when there is paper at the
sor duplex jam 1 sensor (Q08-700).
08-720 Out-Bin Full Sensor Detects when the paper is at the
out bin full sensor (Q08-720).
Code Displayed Name Description
09-310 THV Bias Read Detects the THV value on the
transfer roller.
Code Displayed Name Description
10-200 Fuser Temperature Measures the fuser temperature at
A the thermistor.
April 2010
6-43
Table 3 Input codes 06
General
High = not running at nor-
mal speed
Low = running at normal
speed
Table 4 Input codes 07
General
High = tray empty
Low = paper present
High = tray empty
Low = paper present
High = Tray empty
Low = Paper present
Table 5 Input codes 08
General
High = paper present
Low = no paper
High = paper present
Low = no paper
High = paper present
Low = no paper
High = paper present
Low = no paper
High = paper present
Low = no paper
Table 6 Input codes 09
General
Displays THV value =
XXX
Table 7 Input codes 10
General
Displays temperature in
degrees C = XXX
General Procedures/Information
dC330