Xerox Phaser 3635MFP Service Manual page 29

05-100 DADF Paper Jam 1 RAP
05-100 The lead edge of the document failed to actuate the scan sensor within the correct time
after registration solenoid actuation.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: The door open switch must be actuated to supply +24V to the motors and solenoids.
Refer to Wiring Diagram 10. Perform the following:
1. Open the DADF door assembly, PL 5.10 Item
2. Check the document path for damage or obstructions.
3. Remove the transport assembly upper cover,
4. Check that the following components are clean and rotate freely:
• Registration roll, PL 5.35 Item 9.
• Registration roll idlers, PL 5.15 Item
5. Check that the DADF scan sensor actuator,
aged.
6. Enter dC330 Component Control code 05-140. Check the scan sensor (Q05-140),
5.35 Item 7. If necessary, install a scan sensor.
7. Check the wiring between the DADF scan sensor and CN1 on the
8. Remove the DADF rear cover, PL 5.10 Item
200. Check that the DADF scan motor,
9. Check the wiring between the DADF scan motor and CN9 on the
NOTE: It is not possible to stack component control codes on 3550 machines.
10. 3635 only. Open the DADF door assembly,
door open sensor, PL 5.40 Item 13. Enter
the DADF scan motor. While the DADF scan motor runs, stack the code 05-310 to ener-
gize the DADF registration solenoid (SOL05-310). Check that the registration roll,
Item 9 rotates.
11. 3550 only. Open the DADF door assembly,
door open sensor, PL 5.40 Item 13. Enter
energize the DADF registration solenoid (SOL05-310). To confirm that the solenoid is
functional, listen for a click from the solenoid as it is switched on. Manually actuate the
DADF registration solenoid (SOL05-310), then enter
200 to run the DADF scan motor and check that the registration roll,
rotates.
12. Check the wiring between the DADF registration solenoid and CN8 on the
13. If necessary, install new components:
• DADF PWB, PL 5.15 Item 16.
• DADF scan motor, PL 5.40 Item
• DADF registration solenoid, PL 5.40 Item
• DADF drive assembly, PL 5.40 Item
• Document transport assembly,
Phaser 3635MFP/WorkCentre 3550
3. Remove all jammed paper.
PL 5.35 Item 13.
8.
PL 5.35 Item 6 moves freely and is not dam-
DADF PWB.
9. Enter dC330 Component Control
PL 5.40 Item 2 runs.
DADF PWB.
PL 5.10 Item 3. Manually actuate the DADF
dC330 Component Control code 05-200 to run
PL 5.10 Item 3. Manually actuate the DADF
dC330 Component Control code 05-310 to
dC330 Component Control
PL 5.35 Item 9
DADF
2.
3.
1.
PL 5.35 Item 14.
05-500 DADF Door Open/Jam 5 RAP
05-500 The machine has detected that the DADF door assembly is open during run.
Procedure
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Refer to Wiring Diagram 10. Perform the following:
1. Open the DADF door assembly,
2. Remove all jammed paper from the DADF exit tray.
3. Open the DADF door assembly,
tor is not damaged.
4. Enter dC330 Component Control
160), PL 5.40 Item 13.
5. Check the wiring between the DADF door open sensor and CN5 on the
necessary, install a new DADF door open sensor,
6. If necessary, install new components:
• DADF PWB, PL 5.15 Item
• Document transport assembly,
PL
code 05-
PL 5.35
code 05-
PWB.
April 2010
2-15
WARNING
PL 5.10 Item 3. Remove all jammed paper.
PL 5.10 Item 3. Check that the door open sensor actua-
code 05-160. Check the DADF door open sensor (Q05-
PL 5.40 Item 13.
16.
PL 5.35 Item 14.
Status Indicator RAPs
05-100, 05-500
DADF PWB. If