Xerox Phaser 3635MFP Service Manual page 35

3550 Checkout
Refer to Wiring Diagram 16 (3550) and Wiring Diagram
1. Pull out tray 1. Remove all jammed paper.
2. Check the paper path for damage or obstructions.
3. Remove the tray 1 pickup roll, PL 10.22 Item
necessary, install a new pickup roll,
4. Check the retard pad on tray 1. If necessary, install a new retard pad assembly,
Item 20.
5. Check that the following components are clean and rotate freely:
• Registration roll, PL 8.25 Item 3.
• Registration roll idler, PL 8.25 Item
6. Check that the registration sensor actuator,
aged. If necessary, install a new registration sensor actuator,
7. Enter dC330 Component Control code 08-500. Check the registration sensor (Q08-500).
If necessary, install a new HVPS, PL 1.10 Item
NOTE: The registration sensor is mounted on the HVPS.
8. Enter dC330 Component Control code 04-100 to run the main BLDC motor.
9. Check the wiring between the main BLDC motor and CN22 on the
10. Enter dC330 Component Control code 08-810 to energize the tray 1 pickup solenoid
(SOL8-810), PL 8.25 Item 19. To confirm that the solenoid is functional, listen for a click
from the solenoid as it is switched on. Install a new solenoid if necessary.
11. Check the wiring between the tray 1 pickup solenoid and CN29 on the
12. Check the tray 1 pickup roll, PL 10.22 Item
13. Enter dC330 Component Control
(SOL8-850), PL 8.25 Item 3. To confirm that the solenoid is functional, listen for a click
from the solenoid as it is switched on. Install a new solenoid if necessary.
14. Check the wiring between the registration solenoid and CN29 on the
15. Check that the registration roll, PL 8.25 Item
16. If necessary:
• Install a new front duplex guide assembly,
• Perform OF7 Main PWB Check
Status Indicator RAPs
07-130, 07-210
8. Perform the following:
14. Check that the pickup roll is clean. If
PL 10.22 Item 14.
17.
PL 8.25 Item 14 moves freely and is not dam-
PL 8.25 Item 14.
3.
Main PWB.
Main PWB.
14. If necessary install new roll.
code 08-850 to energize the registration solenoid
Main PWB.
3, If necessary install a new roll.
PL 10.22 Item 15.
RAP.
07-210 Paper Empty at Tray 2 RAP
07-210 The machine has detected that tray 2 is empty.
Procedure
Switch off the electricity to the machine. Disconnect the power cord from the customer
PL 8.10
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 3635 Checkout
• 3550 Checkout
3635 Checkout
Refer to Wiring Diagram 7 (3635),
1. Pull out tray 2. Check that the paper empty actuator,
not damaged.
2. Enter dC330 Component Control
(S07-210), PL 8.17 Item
3. Check the wiring between the paper empty sensor and CN1 on the
sary, install a new paper empty sensor,
4. Check the wiring between CN7 on the
PWB.
5. If necessary:
a. Install a new tray 2 PWB,
b. Perform OF7 Main PWB Check
3550 Checkout
Refer to Wiring Diagram 16
1. Pull out tray 2. Check that the paper empty actuator,
not damaged.
2. Enter dC330 Component Control
(S07-210), PL 8.17 Item
3. Check the wiring between the paper empty sensor and CN1 on the
sary, install a new paper empty sensor,
4. Check the wiring between CN7 on the
PWB.
5. If necessary:
a. Install a new tray 2 PWB,
b. Perform OF7 Main PWB Check
April 2010
2-22
WARNING
Wiring Diagram 11. Perform the following:
PL 8.17 Item 2
code 07-210. Check the tray 2 paper empty sensor
1.
PL 8.17 Item 1.
Tray 2 PWB and CN33 and CN34 on the
PL 8.17 Item 25.
RAP.
(3550), Wiring Diagram 11. Perform the following:
PL 8.17 Item 2
code 07-210. Check the tray 2 paper empty sensor
1.
PL 8.17 Item 1.
Tray 2 PWB and CN35 and CN36 on the
PL 8.17 Item 25.
RAP.
Phaser 3635MFP/WorkCentre 3550
moves freely and is
Tray 2 PWB. If neces-
Main
moves freely and is
Tray 2 PWB. If neces-
Main