Xerox Phaser 3635MFP Service Manual page 198

Table 5 NVM chain 20
Location NVM Name NVM Description
20-520 Error Rate Adjusts the error rate.
20-530 Dial Tone Detect Detects dial tone prior to
sending.
20-540 Loop Current Detects if loop current is
Detect present prior to sending.
20-550 Busy Signal Detects a busy signal to
Detect allow redials.
20-700 Line Monitor Audio line monitor.
Setting
20-800 Modem Speed Select modem start
speed.
20-810 Fax Transmis- Adjusts the fax transmis-
sion Level sion level
20-830 Auto Dial Time- Adjusts the auto dial tim-
out eout
20-840 FAX Batch Send Fax batch send enable
Enable
20-900 FAX Total Send Total of sent fax pages.
Counter
20-910 FAX Total Total of received fax
Receive Counter pages.
Phaser 3635MFP/WorkCentre 3550
Value Default
Off (0) / 5% (1) / 10% (2) / 0
20% (3)
Off (0) 0
On (1)
Off (0) 0
On (1)
Off (0) 0
On (1)
Off (0) 0
On (1)
Comm (2)
Modem_V21_300bps (0) 0
Modem_V27_2400bps (1)
Modem_V27_4800bps (2)
Modem_V29_7200bps (3)
Modem_V29_9600bps (4)
Modem_V33_12000bps (5)
Modem_V33_14400bps (6)
Modem_V17_7200bps (7)
Modem_V17_9600bps (8)
Modem_V17_12000bps (9)
Modem_V17_14400bps (10)
Modem_V34_2400bps (11)
Modem_V34_4800bps (12)
Modem_V34_7200bps (13)
Modem_V34_9600bps (14)
Modem_V34_12000bps (15)
Modem_V34_14400bps (16)
Modem_V34_16800bps (17)
Modem_V34_19200bps (18)
Modem_V34_21600bps (19)
Modem_V34_24000bps (20)
Modem_V34_26400bps (21)
Modem_V34_28800bps (22)
Modem_V34_31200bps (23)
Modem_V34_33600bps (24)
0 to 15dBm 12
10 to 100 seconds 55
Off (0) 0
On (1)
0-0xffffffff 0
0-0xffffffff 0
April 2010
6-37
3550 NVM Read/Write
1. Enter diagnostics, GP 1 Diagnostics
2. For Fax NVM Routines, select DC131 NVM Read/Write - Fax and press the OK key.
3. For machine NVM Routines:
a. Select Machine Diagnostics and press the OK key.
b. Select EDC Mode and press the OK key.
c. Select DC131 NVM Read/Write and press the OK key.
4. Use the up/down keys to select the NVM chain to be viewed and press the OK key.
5. Refer to the tables that follow for NVM chain locations and parameters:
• Table 6 NVM chain 6
• Table 7 NVM chain 7
• Table 8 NVM chain 9
• Table 9 NVM chain 10
• Table 10 NVM chain 20
6. When the values of an editable NVM have been changed, switch off the machine, then
switch on the machine, to check and evaluate the changes made to the NVM.
NOTE: Selecting Reset by pressing the Menu key will cause the selected NVM location to be
reset to its default value. Pressing the return key Cancel closes the window and cancels any
changes made in the now closed window.
NOTE: The CSE cannot read or modify any NVM that contains customer administrative or
accounting data.
Table 6 NVM chain 6
Location NVM Name NVM Description
06-100 Vertical Magnifi- The changed dimension of the
cation vertical direction magnitude.
06-110 Horizontal Magni- The changed dimension of the
fication horizontal direction magnitude.
Table 7 NVM chain 7
Location NVM Name NVM Description
07-100 Top Registration The changed dimension of tray
Tray 1 Simplex 1 top registration in simplex.
07-110 Side Registration The changed dimension of tray
Tray 1 Simplex 1 side registration in simplex.
07-120 Top Registration The changed dimension of tray
Tray 1 Dup_long 1 top registration of 2nd side in
(2nd sid)e duplex long.
07-130 Side Registration The changed dimension of tray
Tray 1 Dup_long 1 side registration of 2nd side
(2nd sid)e in duplex long.
Entry.
Value Default
0mm to 6mm 0
(13 steps /
0.5mm seg.)
0mm to 6mm 0
(13 steps /
0.5mm seg.)
Value Default
0 to 60 (13 steps 30
/ 0.5mm seg.)
0mm to 6mm 3
(13 steps /
0.5mm seg.)
0mm to 6mm 3
(13 steps /
0.5mm seg.)
0mm to 6mm 3
(13 steps /
0.5mm seg.)
General Procedures/Information
dC131