Canon Color iR C3480 Service Manual page 665

Chapter 17
Sub item
ENVP-INT Setting log correction interval of inner machine temperature/humidity/fixing temperature
Setting log collection interval to COPIER>FUNCTION>MISC-P>ENV-PRT and COPIER>DISPLAY>ENVRNT
Settings
0 to 480 <min>
[Factory default/After RAM clear: 60]
Reference Log is not collected when '0' is set.
CNTR-DSP Selecting screen in response to the external controller
Settings
0: The external controllericon is displayed on the control panel of the copier[Factory default/After RAM clear]
(When the color image server is connected.)
1: The control panel of the copier becomes nondisplay mode
(When the control panel-mounted external controller is connected.)
BASE-SW Switching from MEAP-Full model to MEAP-Base model
This is used when trouble originating in the MEAP application has occurred. The MEAP application operation can be
restricted by setting it to "0."
Settings
0: Base model
1: Full model
[Factory setting/value after clearing RAM: 1]
MEMO:
The model can be switched from "1" to "0" only.
SC-L-CNT Switching of sheet size large/small threshold value in scan counter
This sets the https server port when SSL is used by HTTP of MEAP.
0: B4 size sheets are counted as the small size.
1: Letter size sheets are counted as the small size.
[Factory setting/value after clearing RAM: 0]
REPORT-Z Report print attribute flag function control
Switches attribute flags added to report prints.
Setting values
0: PDL text mode
1: PDL photograph mode
2: SCAN text mode
3: SCAN photograph mode
[Factory settings and after RAM clear: 0]
IFXEML-Z Colour iFAX, E-Mail Rx print attribute flag function control
Switches attribute flags added to colour iFAX, E-Mail Rx prints.
Setting values
0: PDL text mode
1: PDL photograph mode
2: SCAN text mode
4: SCAN photograph mode
[Factory settings and after RAM clear: 0]
BMLNKS-Z BMLinks Rx print attribute flag function control
Switches attribute flags added to colour BMLinks Rx prints.
Setting values
0: SCAN photograph mode
1: PDL photograph mode
2: SCAN text mode
3: PDL text mode
[Factory settings and after RAM clear: 0]
DST-POS Setting the switching position for document scanning in DF mode (repeat reading)
Setting the document scanning position compensation when the glass surface is dirty
0: Position #1 + position #2
1: Position #1
2: Position #2
[Factory setting/value after clearing RAM: 0]
Reference:
Position #2 is an open space so floating dirt tends to be reflected on the images.
CCD-LUT Whether data is to be used for CCD gain compensation
This is used to compensate for the deterioration in the images (density differences in the center joins of the images) which
develops over time. Set whether or not to use the values adjusted by selecting COPIER>FUNCTION>CCD>LUT-
ADJ2.
Settings
0: Not used
1: Used
[Factory setting/value after clearing RAM: 0]
ITBB-TMG ITB cleaning band frequency setting
This changes the band image frequency. Lengthening the intervals enables the down time and toner consumption to be
reduced.
Settings
0 to 10 (in increments of 1: One banding per 100 sheets)
No banding at the "0" setting
[Factory setting/value after clearing RAM: 1]
FX-D-TMP Setting of threshold value for starting throughput reduction sequence when small size sheets are passed through
This sets the productivity reduction start temperature for sheets with widths less than A4R and sheets of an undefined
format. It improves the hot offset and productivity of sheets with widths less than A4R and sheets of an undefined format.
Settings
-4 to 4
[Factory setting/value after clearing RAM: 0]
17-62
COPIER>OPTION>BODY
Description level.
1
1
1
1
1
1
1
1
1
1
1