Canon Color iR C3480 Service Manual page 581

Chapter 16
Code Main Cause/Detail of Detection
***: Finisher-Z1 ****: Finisher-Y1, Saddle Finisher-Y2 *****: Puncher Unit
8001 The HP sensor fails to be ON within 1500ms after the paper retaining paddle
starts to move to its HP.
8002 The HP sensor fails to be OFF within 1000ms after the paper retaining paddle
starts to move from its HP.
E584 **** Shutter unit error
8001 The shutter open sensor fails to be OFF (The shutter cannot be closed).
8002 The shutter open sensor fails to be ON (The shutter cannot be opened).
E590 ***** Puncher motor error
8001 The puncher HP sensor fails to be detected after the puncher motor is driven
for 200ms.
8002 The puncher fails to detect the puncher HP sensor after the puncher motor
stops during initial operation.
E591 ***** Puncher dust sensor error
8001 Light receiving voltage at the time of light emission is abnormal.
8002 Light receiving voltage at the time of non-light-emission is abnormal.
E592 ***** Puncher side registration sensor error
8001 Light receiving voltage at the time of light emission is abnormal.
8002 Light receiving voltage at the time of non-light-emission is abnormal.
8003 Light receiving voltage at the time of light emission is abnormal.
8004 Light receiving voltage at the time of non-light-emission is abnormal.
8005 Light receiving voltage at the time of light emission is abnormal.
8006 Light receiving voltage at the time of non-light-emission is abnormal.
8007 Light receiving voltage at the time of light emission is abnormal.
8008 Light receiving voltage at the time of non-light-emission is abnormal.
8009 Light receiving voltage at the time of light emission is abnormal.
800A Light receiving voltage at the time of non-light-emission is abnormal.
E593 ***** Puncher shift motor error
8001 The HP sensor fails to be OFF.
8002 The HP sensor fails to be ON.
E5F0 **** Saddle paper positioning error
8001 The paper positioning plate HP sensor fails to be ON after the paper
positioning plate motor is driven for 1.33 sec.
8002 The paper positioning plate HP sensor fails to be OFF after the paper
positioning plate motor is driven for 1 sec.
E5F1 **** Saddle paper folder error
8001 The number of detection pulses for the paper folder motor clock sensor is
below the specific level.
8002 The paper folder HP sensor fails to change after the paper folder motor is
driven for 3 sec.
E5F2 **** Saddle guide error
8001 The guide HP sensor fails to be ON after the guide motor is driven for 0.455
sec.
8002 The HP sensor fails to be OFF after the guide motor is driven for 1 sec.
E5F3 **** Saddle alignment error
8001 The adjuster plate HP sensor fails to be ON after the jog motor is driven for 0.5
sec. (for 1.67 sec. during initial operation)
8002 The adjuster plate HP sensor fails to be OFF after the jog motor is driven for 1
sec.
E5F4 **** Saddle rear side staple error
8001 The stitching HP sensor fails to be ON after the stitcher motor (rear) rotates in
the adverse direction for 0.5 sec. or more.
8002 The stitching HP sensor fails to be OFF after the stitcher motor (rear) rotates
for 0.5 sec. or more.
E5F5 **** Saddle front side staple error
8001 The stitching HP sensor fails to be ON after the stitcher motor (front) rotates
in the adverse direction for 0.5 sec. or more.
8002 The stitching HP sensor fails to be OFF after the stitcher motor (front) rotates
for 0.5 sec. or more.
E5F6 **** Saddle paper push-on error
8001 The paper pressure plate HP sensor fails to be ON after the paper pressure plate
motor is driven for 0.3 sec. or more.
8002 The paper pressure plate HP sensor fails to be OFF after the paper pressure
plate motor is driven for 80ms or more.
8003 The number of detection pulses for the paper pressure plate motor clock sensor
is below the specific level.
16-8
Countermeasures
Replace the paddle HP sensor (SR8) , Replace the paddle motor
(M6)
Replace the stack ejection motor (M32) , Replace the shutter
open/close clutch (CL31), Replace the shutter HP sensor (PI45)
Replace the puncher HP sensor, Replace the puncher motor
Replace the puncher dust sensor
Replace the end sensor
Replace the side registration sensor 1
Replace the side registration sensor 2
Replace the side registration sensor 3
Replace the side registration sensor 4
Replace the HP sensor, Replace the puncher shift motor
Replace the paper positioning plate motor (M4S), Replace the
paper positioning plate HP sensor (PI7S)
Replace the paper folder motor (M2S), Replace the paper folder
motor clock sensor (PI4S)
Replace the guide motor (M3S), Replace the guide HP sensor
(PI13S)
Replace the jog motor (M5S), Replace the adjuster plate HP
sensor (PI5S)
Replace the stitcher motor (rear, M6S), Replace the stitching
HP sensor (rear, MS5S)
Replace the stitcher motor (front, M7S), Replace the stitching
HP sensor (front, MS7S)
Replace the paper pressure plate motor (M8S), Replace the
paper pressure plate HP sensor (PI14S)
Replace the paper pressure plate motor (M8S), Replace the
paper pressure plate motor clock sensor (PI1S)